DELL 2350d User Manual

							Upgrade the network firmware in the printer or print server.
To ignore the message and continue printing, press the  Back button 
. The current job may not print
correctly.
To cancel the print job, press the  Cancel button 
.
56 Standard Parallel Port Disabled
The printer discards any data received through the parallel port.
To ignore the message and continue printing, press the  Back button 
. The current job may not print
correctly.
To cancel the print job, press the  Cancel button 
.
Ensure that the Parallel Buffer menu item is not set to Disabled. For more information see  Parallel
Buffer .
56 Standard USB Port Disabled
The printer discards any data received through the USB port.
To ignore the message and continue printing, press the  Back button 
. The current job may not print
correctly.
To cancel the print job, press the  Cancel button 
.
Ensure that the USB Buffer menu item is not set to Disabled. For more information, see  USB Buffer
.
58 Too Many Flash Options 
						

							Remove the memory from your printer. Your printer supports up to 160 MB for a non-network printer and
288 MB for a network printer.
58 Too Many Trays Attached Turn the printer off.
Unplug the power cord from the wall outlet.
Remove the excess trays.
Turn the printer back on.
59 Unsupported Tray 
Remove the specified tray, and wait for the message to clear. You must remove the unsupported tray in
order to print.
Turn the printer off.
Unplug the power cord from the wall outlet.
Remove the unsupported tray.
Connect the power cord to a properly grounded outlet.
Turn the printer back on.
81 Engine Code CRC FailureTo ignore the message and continue printing, press the  Back button 
. The current job may not print
correctly. 
						

							To cancel the print job, press the  Cancel button 
.
84 Imaging Drum Life Warning/PC Unit Life Warning
NOTE: You receive the imaging drum life warning only if you have the Toner Alarm set to On.
To ignore the message and continue printing, press the  Back button 
. The current job may not print
correctly.
To cancel the print job, press the  Cancel button 
.
Print a Printer Settings configuration sheet to determine the imaging drum level. For more information,
see  Menu Settings Page
.
Replace the imaging drum, and then reset the counter.
84 Replace Imaging Drum/Replace PC UnitYour printer will not print any more pages until the imaging drum has been replaced.
Replace the imaging drum, and reset the counter.
88 Toner LowRemove the toner cartridge, and firmly shake it to redistribute the toner within the cartridge.
Replace the toner cartridge.
88 Replace Toner Cartridge 
						

							Replace the specified toner cartridge.
To ignore the message and continue printing, press the  Back button 
. The remainder of the print job
may not print correctly.
To cancel the print job, press the  Cancel button 
.
200 Paper Jam
There is a paper jam at the printer input sensor.
Open the front cover by pressing the button on the right side of the printer and lowering the cover.
1.Pull the toner cartridge assembly out of the printer by pulling on the toner cartridge handle.
NOTE: Do not press the button on the toner cartridge assembly.
CAUTION: The inside of the printer might be hot. To reduce the risk of injury from a hot
component, allow the surface to cool before touching it.
2.Remove the jammed paper.
3. 
						

							3.
Install the toner cartridge assembly into the printer.
4.Close the front cover.
5.
201 Paper Jam
There is a paper jam between the printer input and paper exit sensors.
Open the front cover by pressing the button on the right side of the printer and lowering the cover.
1.Pull the toner cartridge assembly out of the printer by pulling on the toner cartridge handle.
NOTE: Do not press the button on the toner cartridge assembly.
2. 
						

							CAUTION: The inside of the printer might be hot. To reduce the risk of injury from a hot
component, allow the surface to cool before touching it. 2.
Remove the jammed paper. 3.Install the toner cartridge assembly into the printer.
4.Close the front cover.
5.
202 Paper Jam
There is a paper jam at the printer exit sensor.
Open the rear exit.
1. 
						

							1.
Remove the jammed paper.
2.Close the rear exit.
3.
231 Paper Jam - Check Duplex
There is a paper jam in the rear of the duplex paper path.
Open the rear exit.
1.Remove the jammed paper.
2.
3. 
						

							2.
Close the rear exit.
3.
233 Paper Jam - Check Duplex
There is a paper jam in the front of the duplex unit.
Remove Tray 1, and then depress the lever in the duplex paper path area.
CAUTION: The inside of the printer might be hot. To reduce the risk of injury from a hot
component, allow the surface to cool before touching it.
1.Remove the jammed paper.
2.Replace Tray 1.
3. 
						

							3.
234 Paper Jam - Check Duplex
There is a paper jam in the duplex unit, but the printer cannot identify the location.
Remove Tray 1, and then depress the lever in the duplex paper path area..
CAUTION: The inside of the printer might be hot. To reduce the risk of injury from a hot
component, allow the surface to cool before touching it.
1.Remove any jammed paper.
2.Replace Tray 1.
3. 
						

							3.
Open the rear exit.
4.Remove any jammed paper.
5.Close the rear exit.
6.
235 Paper Jam - Check Duplex
There is a paper jam at the output bin because the paper used was too narrow for the duplex unit.
Open the rear exit.
1.