Dukane Projector 8120WIA User Manual

							91
Presentation tools
• When the Interactive Function is in use, it is recommended that you 
make use of input signals from the  COMPUTER IN1, COMPUTER IN2, HDMI1/
MHL and HDMI2 ports. 
• Noise through the USB cable may trigger a malfunction depending on the 
computer and projector you are using. When this occurs, check to ensure that 
the power cables of the computer and projector are grounded. Malfunction may 
occur if the cables are not grounded.
• The pen sensor may be blocked if the projector is placed directly on the 
floor. It is recommended the projector be mounted on the wall or ceiling. The 
Interactive Function does not work during rear projection.
• Set the resolution to 1280 x 800 when connecting to a laptop computer . 
Otherwise, the Interactive Function may not operate properly.
• Holding out the hand in front of the camera lens causes malfunction.
• Don't make anything with magnetic force of a magnet approach in the camera 
unit. It'll be sometimes obstruction of the operation with the normal interactive 
function. NOTE
Interactive Function (continued)
►Be careful of the wired cables. Tripping over the cables may
result in injury or damage the projector or computer. CAUTION 
						

							92
Presentation tools
Interactive Function (continued)
The Interactive Function can be set in IWB CALIBRATE of the EASY MENU or 
IWB of the ADVANCED MENU.
USER SETTING
ItemDescription
AUTO 
CALIBRATE Performs the initial setting of the Interactive Function 
automatically.
• The following pattern image is displayed while executing 
AUTO CALIBRATE. The pattern image disappears when AUTO 
CALIBRATE is completed.
• Try adjusting by MANUAL CALIBRATE if the position of pen 
does not coincide with the drawn line after executing AUTO 
CALIBRATE.
(continued on next page)
• Accuracy of AUTO CALIBRATE might decrease if you execute AUTO 
CALIBRATE just after turning on the projector. Wait more than 2 minutes after turning on 
the projector to execute AUTO CALIBRATE.
• Stay away from the projector until AUTO CALIBRATE is completed.
• AUTO CALIBRATE may fail when interfering light falls on the image of the 
projector. Be sure not to let the light fall directly on the screen.
• AUTO CALIBRATE may fail depending on the installation environment. In this 
case, try adjusting by MANUAL CALIBRATE.
• AUTO CALIBRATE may fail with the board or screen of dark color. NOTE 
						

							93
Presentation tools
Interactive Function (continued)
ItemDescription
MANUAL
CALIBRATE Using bundled pen performs the initial setting of the Interactive 
Function.
Click on the center of the marker displayed in the image from 
the projector with a bundled pen.
Every time you click with a bundled pen, the position of the 
marker changes. MANUAL CALIBRATE is completed when 
clicking 16 markers in total.
• CALIBRATE is required again when installation situation of the 
projector is changed or display region of the image is changed by the functions 
such as D-ZOOM/D-SHIFT etc.  NOTE
(continued on next page) 
						

							94
Presentation tools
Interactive Function (continued)
ItemDescription
IWB SETUPSelect this item and press the ► cursor button or ENTER 
button to display IWB SETUP menu.
Select an item using the ▲/▼ cursor buttons.
IWB MODE
Press the ► cursor button or ENTER button to set IWB MODE.
(1)Select the input port to change setting using the ▲/▼ cursor 
button.
(2)Select IWB MODE using the ◄/► cursor button.
    PC INTERACTIVE 
⇔ PC LESS INTERACTIVE 
⇔ OFF
PC INTERACTIVE : PJ internal Painter mode, PJ operation mode, and PC 
operation mode of Interactive tool  (
100) are available.
PC LESS INTERACTIVE : PJ operation mode and PJ internal Painter mode of 
Interactive tool are available.
OFF : Interactive tool is unavailable.
FINGER TOUCH
Select ON/OFF of FINGER TOUCH function using the ◄/► 
cursor button.
    ON  ⇔ OFF
・ Select ON if you use FINGER TOUCH UNIT(Optional parts
：
FT-01B) for interactive operation by finger. 
・ Select OFF if you operate by bundled pen.
(continued on next page) 
						

							95
Presentation tools
Interactive Function (continued)
ItemDescription
IWB SETUP
(Continued) CAMERA VIEW
Press the ► cursor button or ENTER button to display OSD 
menu of CAMERA VIEW. Camera image is displayed on the 
menu.
・ This function is for the adjustment of FINGER TOUCH 
UNIT(Optional parts ：FT-01B) .
For more information, refer to the manual of FINGER TOUCH 
UNIT.
MOUSE TYPE
Select MOUSE TYPE using the ◄/► cursor button.
    MULTI  ⇔ SINGLE
・ When selecting MULTI, whether multi touch is supported or 
not by connected computer is judged automatically.
When using PC operation mode of Interactive tool (
100), you 
can use multi touch if your computer supports multi touch.
・ When selecting SINGLE, you cannot use multi touch of PC 
operation mode.
NOTE
・ Select SINGLE if mouse operating of PC operation mode 
does not work well with selecting MULTI.
(continued on next page) 
						

							96
Presentation tools
Interactive Function (continued)
ItemDescription
CALIBRATE 
SETUP Select this item and press the ► cursor button or ENTER 
button to display CALIBRATE SETUP menu.
Select an item using the ▲/▼ cursor buttons.
SCREEN TYPE
Select SCREEN TYPE using the ◄/► cursor button.
    16:10 
⇔ 4:3 
・ The area of screen is set according to the selected 
SCREEN 
TYPE(ratio of height and width).
・ The guide of setting area of screen is displayed.
NOTE
・ When changing SCREEN TYPE, execute AUTO CALIBRATE 
(
92) or MANUAL CALIBRATE (93).
・ After executing calibration, display calibration pattern and 
adjust according to SCREEN TYPE. 
・ The position of pen is followed automatically if setting of 
resolution or aspect (
46) of input signal is changed.  So you 
don't have to execute calibration again.  
・ When a part of image is displayed going beyond the set area, 
the function does not work even if touching the point in the 
area by pen.
(continued on next page) 
						

							97
Presentation tools
Interactive Function (continued)
ItemDescription
CALIBRATE 
SETUP
(Continued) IWB AREA SETUP
Press the 
▶ cursor button or ENTER button to set IWB AREA SETUP.
Select AUTO or MANUAL using the ▲ / ▼ cursor button.
    AUTO  ⇔ MANUAL
・ When selecting AUTO, the area of mouse cursor with PC operation 
mode of Interactive tool 
(101) is adjusted automatically .
・ When selecting MANUAL, Adjust the area of mouse cursor with PC 
operation mode by manual operation.
Adjusting the area of mouse cursor by manual operation
・ Select MANUAL and press the 
▶ cursor button or ENTER 
button to move mouse cursor on the screen.
・C lick the position of mouse cursor by the pen at the upper left 
and then click at the lower right similarly.
NOTE
・ Adjusting by manual operation is unavailable if there is no 
signal.
・ Try again if adjusting by manual operation is failed.
・ When selecting AUTO, if following trouble happens 
depending on computer, select MANUAL. Though the position 
of pen coincides with the drawn line with PJ internal Painter 
mode of Interactive tool, the position of pen does not coincide 
with the cursor of mouse operating with PC operation mode.
(continued on next page) 
						

							98
Presentation tools
Interactive Function (continued)
ItemDescription
MULTI 
DISPLAY Select ON/OFF of MULTI DISPLAY using the 
▲ / ▼ cursor 
button.
    ON  ⇔ OFF
・ Select ON if using MULTI DISPLAY function.
・ Select OFF if not using MULTI DISPLAY function.
NOTE
・ When selecting ON, IWB MODE 
(
94) is not able to be set.
・ When selecting ON, Interactive tool 
(
100) is unavailable.
MEMORY  ACCESS Select MEMORY ACCESS setting using the 
▲ / ▼ cursor 
button.
    PROJECTOR  ⇔ COMPUTER
・ Select PROJECTOR to display template data which stored 
inside memory of projector on thumbnail of USB TYPE A.
・ Select COMPUTER to operate internal memory of projector 
as USB memory by the computer connected to USB TYPE B 
port.
NOTE
・ Select PROJECTOR to use USB Display 
(
126).
(continued on next page) 
						

							99
Presentation tools
When selecting PC INTERACTIVE mode or PC LESS INTERACTIVE mode of the 
IWB MODE, you can use internal paint tool of the projector.
Main Functions
It offers effective features for making classroom and business presentations more
fun and easier to understand.
Drawing on projected images
You can draw pictures or text on images projected by our projectors.
Saving and displaying drawn images
You can save images with pictures or text drawn on them to a USB memory 
device and then call out the saved images and display them again later.
Using as a simple mouse
The product can be used in place of the mouse of a computer connected to a 
projector. Interactive Function (continued)
• The authorization by the copyright owner(s) is required pursuant to 
applicable laws for the use of works including visual images, if such works are 
copyrighted works.
• Drawing with the Interactive Function is not possible with some image signals. NOTE
• A USB memory device is necessary to utilize this function.
• Copyright protected images cannot be saved. NOTE
• To use this function, a USB cable is required to connect the computer 
and the projector.
NOTE 
						

							100
Presentation tools
Using Interactive tool.
Touch the projected image using the bundled pen to display initial operation tool 
bar and use Interactive Function. 
   PC operation mode： 
Shifts to PC operation mode.
   PJ internal Painter mode： 
Shifts to PJ internal Painter mode.
   PJ operation mode： 
Shifts to PJ operation mode.
  Deletes tool bar and exits Interactive Function.
  Minimizes tool bar display. 
Touch minimized icon to return the tool bar display.
NOTE ・When selecting ON of MULTI DISPLAY (
98), this tool is unavailable.
・Tool bar disappears automatically if there is no operation for several seconds.
・Multi touch with PC operation mode and PJ internal Painter mode supports to  6 pens.
Interactive Function (continued)