Eiki Eip-1 Multimedia Projector Owners Instruction Manual

							20
5.4 Display (Video mode) 
 
 
 
 
Submenu   Purpose   Using 
Keystone  To modify the biased 
image resulting from the 
improper angle of 
projector. Press 
						

							21  
User Blue 
To adjust the Blue color.Press 
						

							22
5.5 Audio 
 
 
 
Submenu    Purpose or Using 
Vo l u m e   Press 
						

							23
5.6 Management 
 
 
Submenu   Purpose   Using 
OSD Location To display the position of menu on 
the screen. Press 
						

							24 Lamp Reset To recount hours after replacing   
the lamp. Press the right key. The 
message “Press Enter key 
to confirm lamp reset 
operation!” appears. Please 
check if the user has 
replaced the new lamp. If 
yes, press Enter key. If not, 
press Menu key or Esc key 
on the remote controller to 
quit. 
Auto Adjust For end users to fix the brightness 
and contrast settings. This function 
only works in the VGA mode. Choose Ye s. The values of brightness and contrast vary 
each time when pressing 
Auto key.   
Choose No. The values of 
brightness and contrast 
remain the same. 
Reset All To return to the factory default.  Press the right key. 
Source Type To select RGB, Composite, 
Component, HDTV(**),S-Video, 
signals or Auto Scan. Press 
						

							25
6.1 Replacing the lamp 
30 hours before the end of the lamp’s life time, the warning message “Lamp life 
time is up! Replacement suggested!” will display on the screen. Please replace the 
lamp immediately. 
 
Steps: 
1. Power off the projector. 
2. Unplug the power cord. 
3. Cool down projector for at least 30 minutes. 
4. Use a screwdriver to remove the shell and screws on the lamp. 
5. Remove lamp. 
6. Gently process the new lamp module into the lamp bay, then replaces the lamp 
module retaining screws. 
7. Replace the lamp bay access panel, and then replace the access panel screw. 
 
 
 
 
 
 
 
 
6.2 Cleaning lens 
Please follow these steps to clean the projector lens: 
1 Pour an adequate amount of cleanser to a piece of clean soft material. The lens 
will be damaged if you use the cleanser containing particles, solvent, or other 
inferior chemical solvent. 
2 Use the soft material to wipe the lens in a circular direction. 
3 Cover the lens with the cap if you are not going to use the projector right away. 
Remove screws from the lamp
cover with a screwdriver; an
d
then press down the lock to
open that cover. 
Remove 3 screws from
the lamp holder; and
pull out the handle to
replace the lamp in the
holder.  
						

							26
7. Appendix 
7.1 Common problems and trouble-shooting 
If you are having a problem with your projector, please check the following: 
If you still cannot solve the problem, please contact your local distributor or our 
service center. 
 
Q.: No image on the screen at all? 

						

							27 Q.: Image becomes blurred 

						

							28
7.2 Specifications  
 
 
 
 Model No. 
EIP-1 
Resolution  XGA (1024*768) 
Size  229 x 193 x 69 mm 
We i g ht   3.5 lbs 
Lamp  150W VIP 
Brightness 1400 Lumens 
Projection distance 1.45m ~10m 
Throw Ratio 1.34:1 ~ 1.6:1 (Distance: Diagonal) 
Zoom Ratio 1.2:1 (Manual Zoom/Focus) 
Uniformity 85% 
Aspect Ratio 4:3 / 16:9 screen selectable 
Contrast Ratio 900:1 
Horizontal Frequency31.5 - 80 kHz 
Vertical Scan Rate 56 - 85 Hz 
Video compatibility 
NTSC / PAL 
VGA compatibility RGB/DVD 480P, HDTV (1080i/720P/480P) 
Power supply 100 to 240 VAC, 0.91A~2.2A,50 to 60 Hz 
Power Consumption 220W 
   
						

							29  
Input Terminal   
y DVI (M1DA) y USB y RGB (M1DA-D-Sub 15 pin)
y RS232 (M1DA) y YPbPr (M1DA,VGA)y S-Video Mini DIN 4 pin 
y Audio: RCA Jacky 3.5mm Mini Jack y Composite Video (RCA Jack)
 
Output Terminal   
y 1 watt speaker 
 
* All specifications are subject to change without notice. 
 
 
 
This device complies with Part 15 of the FCC Rules. Operation is subject to the 
following two conditions: (1) the device may not cause harmful interference, and 
(2) this device must accept any interference received, including interference that 
may cause undesired operation.