Epson AcuLaser C4200DNPC5 User Manual

11
Memory Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 389Print quality decreased  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 389
Insufficient memory for current task. . . . . . . . . . . . . . . . . . . . 389
Insufficient memory to print all copies . . . . . . . . . . . . . . . . . . 389
Paper Handling Problems  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 390 Paper does not feed properly . . . . . . . . . . . . . . . ....

12
Appendix A  Customer Support
Contacting Customer Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  408
Technical Support Web Site  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  408
Appendix B   Technical Specifications
Paper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  410 Available paper types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  410
Paper that should not be used . . . . . . . . . ....

13
Downloading Fonts  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 453
EPSON Font Manager (Windows Only) . . . . . . . . . . . . . . . . . 453
Symbol Sets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 456 Introduction to Symbol Sets  . . . . . . . . . . . . . . . . . . . . . . . . . . . 456
In the ESC/P 2 or FX Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . 458
In the I239X Emulation Mode . . . . . . . . . . . . . . . . . ....

14Safety Instructions
Safety Instructions
New :describe
 t
he
 same
 information
 as
 H_SAFE
.MIF
Safety Information
Warnings, Cautions, and Notes
w
Warnings
must be followed carefully  to avoid bodily injury.
c
Cautions
must be observed to avoid damage to your equipment.
Notes 
contain important information and useful tips on the operation of your 
printer.
Safety precautions
N ew :confirm the  product
 specification a
nd
 delete
 unnecessary i
nformationBe sure to follow the precautions carefully to...

Safety Instructions15
❏Because the printer weighs approximately 34.6 kg (76.3 lb) 
with consumable products installed, one person should not 
lift or carry it. Two people should carry the printer, lifting it 
by the correct positions as shown below.
❏ Be careful not to touch the fuser, which is marked  CAUTION 
HIGH TEMPERATURE , or the surrounding areas. If the printer 
has been in use, the fuser and the surrounding areas may be 
very hot. If you must touch one of these areas, wait 30 minutes 
to allow...

16Safety Instructions1. Do not insert your hand deep into the fuser unit.
2. 
CAUTION HIGH TEMPERATURE
❏ Do not insert your hand deep into the fuser unit as some 
components are sharp and may cause injury.
❏ Avoid touching the components inside the printer unless 
instructed to do so in this guide.
❏ Never force the printer’s components into place. Although the 
printer is designed to be sturdy, rough handling can damage 
it.
❏ When handling a toner cartridge, always place it on a clean, 
smooth...

Safety Instructions17
❏When removing the photoconductor unit, avoid exposing it 
to room light for more than five minutes. The unit contains a 
green-colored light-sensitive drum. Exposure to light can 
damage the drum, causing dark or light areas to appear on 
the printed page and reducing the service life of the drum. If 
you need to keep the unit out of the printer for long periods, 
cover it with an opaque cloth.
❏ Be careful not to scratch the surface of the drum. When you 
remove the...

18Safety Instructions
When choosing a place and power source for the printer
❏Place the printer near an electrical outlet where you can easily 
plug in and unplug the power cord.
❏ Do not place the printer on an unstable surface.
❏ Do not put your printer where the cord will be stepped on.
❏ Slots and openings in the cabinet and the back or bottom are 
provided for ventilation. Do not block or cover them. Do not 
put the printer on a bed, sofa, rug, or other similar surface or 
in a built-in...

Safety Instructions19
❏When connecting this product to a computer or other device 
with a cable, ensure the correct orientation of the connectors. 
Each connector has only one correct orientation. Inserting a 
connector in the wrong orientation may damage both devices 
connected by the cable.
❏ If you use an extension cord, ma ke sure that the total of the 
ampere ratings on the products plugged into the extension 
cord does not exceed the extension cord ampere rating.
❏ Unplug this printer from the...

20Safety Instructions
❏
Follow all warnings and instructions marked on the printer.
❏ Unplug this printer from the wall outlet before cleaning.
❏ Use a well-wrung cloth for cleaning and do not use liquid or 
aerosol cleaners.
❏ Avoid touching the components inside the printer unless 
instructed to do so in the printer’s documentation.
❏ Never force printer components into place. Although the 
printer is designed to be sturdy, rough handling can damage 
it.
❏ Be sure to keep consumables out of the reach...