Epson P7000 User Manual

							Getting Started 11
Installing the BatteryThe viewer comes with a lithium-ion battery. 
1Slide the battery cover to the right to open it.
2Insert the battery into the compartment in the direction 
of the arrow on the battery.3Close the battery cover and slide it to the left until it 
clicks.
Charging the BatteryAfter installing the battery, you need to charge it using the 
AC adapter. It takes about 3.5 hours to fully charge the 
battery when the viewer is off, and longer when the viewer 
is on.
The 
Charge
 light is green while the battery is being 
charged. When the battery is fully charged, the light 
turns off.  
						

							Getting Started 12
To charge the battery, connect the AC adapter as shown 
below. Connect the other end to the power cord and plug it 
into an electrical outlet.Caution: 
Do not connect the AC adapter when the battery is not installed; 
this can damage the viewer. Turn off the viewer before 
disconnecting the AC adapter.The battery status is displayed in the top right corner of the 
LCD screen when the viewer is on.Note: 
The battery may become hot when the viewer is operated 
during charging. Charging will stop until the battery cools down. 
Removing the BatteryIf you plan to store the viewer for an extended period of 
time, you should remove the battery.
1Make sure the viewer is turned off (see page 16). 
Caution: 
Remove the AC adapter if it is connected to the viewer.
Never remove the battery while the viewer is turned on. 
Doing so may cause files to be lost or damaged.
2Open the battery cover.
3Slide the battery release lever to the left. The battery 
pops out.
Battery is fully charged.
Battery power is about half full.
Battery power is low.
Battery is charging. 
						

							Getting Started 13
4Pull out the battery. Then close the battery cover.Note: 
If you remove the battery, the date and time settings will be 
erased after about one day. The next time you turn on the 
viewer, the date and time setting screen will be displayed.
Turning On the PowerSlide the power switch down as shown below, then release it. 
The activity light flashes for a moment then turns off.Setting the Language, Date, and TimeThe first time you turn on the viewer, you see the Language 
setting screen:Activity 
light 
						

							Getting Started 14
Note: 
If you see the Home screen instead (as shown in “Using the 
Home Screen” on page 15), the language has already been 
selected. To change it or check the date and time, select 
Settings on the Home screen. Then follow the instructions in 
“Date and Time” or “Language” on page 73.1Press 
OK
 to select 
English
. You see a message about 
setting the date. 
2Press 
OK
. You see the Date and Time screen:
3Press right or left on the 4-way ring to highlight a setting 
to change. 
4Press up or down on the 4-way ring to change the 
setting (such as the year).
5After setting the date, set the date format.6When you finish, highlight 
Complete 
and press 
OK
. 
You see the Home screen. See page 15 for details.
Note: 
If you remove the battery, the date and time settings will be 
erased after about one day. The next time you turn on the 
viewer, the date and time setting screen will be displayed. Locking the ButtonsYou can lock the buttons on the viewer. This allows you to 
place the viewer in a purse or backpack and use it with 
headphones without accidentally pressing the buttons.
To lock the buttons, slide the power switch to 
Hold
.
To unlock the buttons, slide the power switch back to the 
middle position. 
						

							Getting Started 15
Using the Home ScreenWhenever you turn on the viewer, the Home screen 
appears. All operations can be started from this screen. 
The following table summarizes the Home screen.Icon Function
 Battery
 iconIndicates the remaining charge in the battery. 
See “Charging the Battery” (page 11).
 CF icon Indicates that a memory card is inserted in the 
CompactFlash slot.
 SD icon Indicates that a memory card is inserted in the 
SD slot.
Battery icon Hold icon
SD iconCF icon
 Hold 
 iconIndicates that the buttons are locked. See 
“Locking the Buttons” (page 14).
 Backup 
 FilesView folders and files backed up from memory 
cards or USB devices. 
 My
 PhotosView folders and files that you have copied 
into the Photos folder. See “Viewing Images” 
(page 27).
 My
 VideosView folders and play videos that you have 
copied into the Videos folder. See “Viewing 
Videos” (page 32).
 My 
MusicListen to music copied from your computer. 
See “Playing Audio Files” (page 38).
 Memory 
CardView files on memory cards or copy the files 
to the viewer. See “Copying Files From a 
Memory Card” (page 20).
 USB 
 DeviceCopy files to or from a USB device. See 
“Using the Viewer With USB Devices” (page 
48).
 Settings Check and adjust viewer settings. See 
“Customizing Settings” (page 70).
 Print 
WizardEdit and print photos you have copied to the 
viewer. See “Printing” (page 60). Icon Function 
						

							Getting Started 16
Tu r n i n g  O f f  t h e  P o w e rBefore you turn off the viewer, make sure the memory card 
access light is off. Then slide the power switch as shown 
below, and hold it down for a few seconds until the activity 
light flashes and the viewer turns off.
Saving PowerWhen you are not using the viewer, it goes into one of the 
power-saving modes listed below. You can adjust the timing 
for all of the power-saving modes; see “Power Save” on 
page 71 for more information.❍
The LCD screen turns dark after one minute of 
inactivity. Press any button to turn it on.
❍
The LCD screen turns off after five minutes of 
inactivity. Press any button to turn it on.
❍
The viewer turns off automatically after 10 minutes of 
inactivity. Slide down the power switch to turn it back 
on. 
When the AC adapter is connected, the viewer plays a 
screen saver after three minutes of inactivity instead of 
turning off. 
To customize the screen saver, see “Selecting a Screen 
Saver” on page 58. 
Memory card 
access light
Activity 
light 
						

							Using Memory Cards 17
Chapter 2Using Memory CardsThe viewer has two memory card slots: one for 
CompactFlash or Microdrive
™ cards, and one for SD 
(Secure Digital) and MultiMediaCard cards.
This chapter explains how to insert and remove memory 
cards and how to display and copy files.
Inserting and Removing Memory 
CardsThe viewer supports the following types of memory cards:With a CompactFlash adapter, you can use the memory 
cards listed below in the 
CF Card
 slot:
Caution: 
Make sure you follow all instructions included with your 
memory card. 
Never remove a memory card, or shake or drop the viewer 
while the memory card access light is flashing. Doing so may 
cause files to be lost or damaged.
Do not put labels or stickers on memory cards. The sticker may 
peel off, preventing the card from being ejected and damaging 
the viewer.
Avoid using or storing cards in direct sunlight, or in places that 
are extremely hot, humid, or dusty. ❍
CompactFlash (Type2 and 3.3V)
❍
Microdrive
❍
Secure Digital (up to 2GB)
❍
SDHC (up to 32GB)
❍
MultiMediaCard
❍
MMCplus (up to 4GB)
❍
miniSD
™ Card
❍
Memory Stick PRO Duo
™
❍
Memory Stick
™
❍
xD-Picture Card
™
❍
Memory Stick Duo
™
❍
SmartMedia Card
❍
Memory Stick PRO
™
❍
RS-MMC Card 
						

							Using Memory Cards 18
Using the CF Card SlotYou can use Type2 and 3.3V CompactFlash cards or 
Microdrive cards in the 
CF Card
 slot. If you have a 
CompactFlash adapter, you can also use other types of cards, 
as described in “Inserting and Removing Memory Cards” 
on page 17.
Insert the memory card into the slot with the label facing 
forward. Then push the memory card all the way into the 
slot.
If you are using a CompactFlash adapter, put the card into 
the adapter and insert the adapter into the slot.
Caution: 
Make sure you insert memory cards in the correct orientation. 
Otherwise, the card and viewer may be damaged.
To remove a card from the 
CF Card
 slot, first make sure the 
memory card access light is off. Then press the eject button 
and pull out the card. 
If the button is not sticking out, press it once to pop it out, 
then press it again to eject the card.
Note: 
If you are using a CompactFlash adapter, remove the adapter 
from the viewer; do not remove only the memory card. 
						

							Using Memory Cards 19
Using the SD Card SlotYou can use Secure Digital, SDHC, MultiMediaCard, or 
MMCplus cards in the 
SD Card
 slot.
Insert the memory card into the slot as shown below. Then 
push the memory card all the way into the slot.
Caution: 
Make sure you insert memory cards in the correct orientation. 
Otherwise, the card and viewer may be damaged.
To remove a card from the 
SD Card
 slot, first make sure the 
memory card access light is off. Then press in on the top of 
the card. 
When the card pops up, pull it out of the slot. 
						

							Using Memory Cards 20
Copying Files From a Memory CardAfter you insert a memory card, you can browse the files and 
decide what you want to do with them, or simply copy all 
the files on the card to the viewer.Note: 
If the battery power is low, copying may not be completed. Use 
the AC adapter when copying files.Copying All Files1Insert a memory card.
If the Memory Card menu doesn’t open automatically, 
select 
Memory Card
 on the Home screen, then press 
OK
. You see the following menu:
2Select 
CF Memory Card Backup
 or 
SD Memory 
Card Backup
. Then press 
OK
. The files are copied to a folder that is automatically created 
in the Backup Files folder on the viewer. The folder is 
named according to the date and the date format you 
selected, for example, 
03292008M.001
. Folders are 
numbered in the order they are copied. 
If you want to change the name, see “Creating a New Folder 
and Copying Files” on page 22.
When the backup is complete, you see thumbnail images of 
the copied photos.
Note: 
The files on the memory card can be automatically deleted after 
copying is complete. For details, see “Backup Settings” on 
page 72.To check the copied files, select 
Backup Files
 on the Home 
screen, then press 
OK
. Press 
OK
 again to select the folder 
you just copied and display the files.