GE Logiq P5 User Manual

LOGIQ 5 Basic User Manual 3-1
Direction 2300002-100 Rev. 2
Chapter 3
Preparing the System for Use
Describes the site requirements, console overview, 
system positioning/transporting, powering on the 
system, adjusting the display monitor, probes and 
operator controls. 

Preparing the System for Use
3-2 LOGIQ 5 Basic User Manual
Direction 2300002-100 Rev. 2
Site Requirements
Introduction
NOTE:  Only qualified physicians or sonographers should perform 
ultrasound scanning on human subjects for medical diagnostic 
reasons. Request training, if needed.
Do not attempt to install the system alone. General Electric, 
Affiliate, or Distributor Field Engineers and Application 
Specialists will install and setup the system.  See ‘Contact 
Information’ for more information.
The...

Site Requirements
LOGIQ 5 Basic User Manual 3-3
Direction 2300002-100 Rev. 2
Before the system arrives
NOTICE This medical equipment is approved, in terms of the prevention 
of radio wave interference, to be used in hospitals, clinics and 
other institutions which are environmentally qualified. The use of 
this equipment in an inappropriate environment may cause 
some electronic interference to radios and televisions around 
the equipment. This equipment can be used in residential areas 
only under the...

Preparing the System for Use
3-4 LOGIQ 5 Basic User Manual
Direction 2300002-100 Rev. 2
Environmental Requirements
The system should be operated, stored, or transported within 
the parameters outlined below. Either its operational 
environment must be constantly maintained or the unit must be 
turned off.
Table 3-1: System Environmental Requirements
OperationalStorageTransport (

Console Overview
LOGIQ 5 Basic User Manual 3-5
Direction 2300002-100 Rev. 2
Console Overview
Console graphics
The following are illustrations of the console:
 Figure 3-1. LOGIQ 5 System (right and left side views)
1.  Probe and Gel Bottle Holder
2.  Storage area of Peripheral Device
3.  Storage area of Peripheral Device
4.  Release lever to raise and lower Monitor and Control Panel
5. Side Pocket
6. Task Light
100-120V  150VA Max
6
23
4
5 31
CAUTIONDO NOT place probes or the footswitch into either the...

Preparing the System for Use
3-6 LOGIQ 5 Basic User Manual
Direction 2300002-100 Rev. 2
Console graphics (continued)
 Figure 3-2. LOGIQ 5 System (front and back views)
1.  Optional B/W Video Page Printer
2.  Probe Ports with optional CWD Probe Port, when available
3. Footswitch connector
4.  Optional Physiological Input Panel
5. MOD
6. CD ROM
7. Rear Panel
8. Task Lamp
8
1
6
5
42
3
7 

Console Overview
LOGIQ 5 Basic User Manual 3-7
Direction 2300002-100 Rev. 2
External drives (CD-RW and/or MO) 
The external CD-RW drive (Standard) and MO drive (Option) are 
located next to the probe port.
They can be used to perform software upgrades, image 
archiving and service diagnostics.
CAUTIONMake sure that the CD-RW Disk tray and/or MO Disk are 
securely placed in each device during system operation. 
Mechanical damage may occur if other objects hit the tray or 
MO disk. 

Preparing the System for Use
3-8 LOGIQ 5 Basic User Manual
Direction 2300002-100 Rev. 2
Storage areas
Several convenient storage areas are provided within the 
console as shown in the figure below. Use them to store gel, 
options, probe cables, accessories, etc.
 Figure 3-3. Storage Areas
1. Storage Areas
100-120V  150VA Max
PDIPW
L
R B Pause Auto
DepthMZoom
Ellipse Body PatternMeasure
M/D Cursor
Scan AreaSetClear Comment
Patient
21L21
1
1
1
1
1 1
1
CAUTIONDO NOT place probes or the footswitch into...

Console Overview
LOGIQ 5 Basic User Manual 3-9
Direction 2300002-100 Rev. 2
Task Lamp
The task lamp is used to illuminate the keyboard. 
 Figure 3-4. Task Lamp
1. Task lamp
CAUTIONThe task lamp may overheat. Take proper precautions to avoid 
touching the task lamp. 
Contact your local Service Representative when the task lamp 
bulb needs to be replaced.
1. 

Preparing the System for Use
3-10 LOGIQ 5 Basic User Manual
Direction 2300002-100 Rev. 2
Peripheral/Accessory Connection
Peripheral/Accessory Connector Panel
LOGIQ 5 peripherals and accessories can be properly 
connected using the rear connector panel located behind the 
rear door. Only the B/W Printer can be connected to the front 
accessory panel.
Located on the rear panel are video input and output, audio 
input and output, camera rec/expose, Insite, Ethernet, power 
and control connections for VCR,...