Getnet Router GR-534W User Manual

							 
96 
 
 
On this page, you can modify the parameters of PROF001, such as SSID, network 
type and security mode.   
  Activate a Profile 
If you want to delete a preset profile (e.g. PR0F001), choose this profile and then click 
the Activate button. The activated file will be marked with an icon 
.See the 
following figure:  
						

							 
97 
 
 
5.5.2  Link Status 
Click Wireless > Link Status to display the Station Link Status page. 
 
 
On this page, you can view the connection status of AP in the STA mode. 
5.5.3  Site Survey 
Click Wireless > Site Survey to display the Station Site Survey page.  
						

							 
98 
 
 
On this page, you can view the scanned APs, scan the nearby APs, connect an AP, or 
add the connection parameters of an AP to the profile list. 
  Connect an AP 
If you want to connect an AP, choose the AP’s SSID, and then click the Connect 
button. If this AP is not encrypted, click the Apply button on the following page to 
establish connection.  
						

							 
99 
 
 
If this AP is encrypted, click the Connect button, and the following page appears. 
 
 
On this page, you need to enter the password in the Pass Phrase field. 
After clicking the Apply button, and if this encrypted AP is connected successfully, 
the SSID of this AP is marked with a green icon 
.  
						

							 
100 
 
 
  Scan APs 
Click the Rescan button on the Station Site Survey page, and then you can rescan 
the nearby APs. If new APs are detected, Site Survey table will be refreshed. 
  Add a Profile 
On the Station Site Survey page, select an AP in the Site Survey table, and then 
click the Add Profile button to enter System Configuration page. On System 
Configuration page, click the Apply button to add this AP to the profile list. 
5.5.4  Statistics 
Click Wireless > Statistics to display the Station Statistics page.  
						

							 
101 
 
 
On this page, you can view the status of transmitted and received data. 
Click the Reset Counters button, and then the data statistic information can be 
refreshed.
 
5.5.5  Advance 
Click Wireless > Advance to display the Station Advanced Configurations page.  
						

							 
102 
 
 
This page is used to enable the wireless function, configure the wireless advanced 
properties, and set the HT physical mode. 
  Advance Configuration 
 
 
The parameters of Advance Configuration are described as follows: 
Field Description 
Wireless Mode 
(Infra) The wireless modes include: 
   802.11 B/G mixed mode 
  802.11 B Only 
  802.11 G Only 
  802.11 N Only  
						

							 
103 
Field Description 
  802.11 GN mixed mode 
   802.11 B/G/N mixed mode 
The default wireless mode is 802.11 B/G/N mixed 
mode. 
Country Region 
Code Select the proper country region code. For 
example, America’s (FCC) channel range is 1~11. 
Europe (ETSI) channel range is 1~13. 
B/G Protection  If 802.11b and 802.11g coexist on your network, it 
is recommended you enable this option. In this 
way, the probability of data collision will be 
reduced, but the transmission efficiency will also 
be reduced. 
You may select Auto, On, or Off. 
   Auto: If selecting this option, AP enables or 
disables the B/G protection mode according 
to the network status.   
   On: Enable the B/G protection mode. 
   Off: Disable the B/G protection mode. 
Tx Rate  You may select a proper data rate in the drop 
down list. You may also leave it blank. 
If selecting Auto, AP will automatically judge the 
data rate. If selecting a higher data rate, the 
transmission distance will be shorter. 
Tx Burst  Enable or disable Tx Burst. After enabling this 
option, the transmission efficiency can be 
improved. 
 
  HT Physical Mode 
When the wireless mode is 802.11 N Only, 802.11GN mixed mode, or 802.11B/G./N 
mixed mode, you may set the parameters of HT physical mode.  
						

							 
104 
 
 
The parameters of HT Physical Mode are described as follows: 
Field Description 
HT  You may select MM (Mixed Mode) or GF (Green 
Field). The default setting is MM. 
BW (Bandwidth)  You may select 20 or Auto. 
GI (Guard Interval)  You may select Long or Auto. 
MCS  MCS (Modulation and Coding Scheme) is for 
denoting the WLAN data rate. The default setting 
is Auto. 
 
5.5.6  QoS 
Click Wireless > QoS to display the Station QoS Configurations page.  
						

							 
105 
 
 
This page is used to configure the wireless QoS properties in the station mode. 
  QoS Configuration 
 
 
The parameters of QoS Configuration are described as follows: 
Field Description 
WMM  Enable or disable WMM. 
WMM Power Saving  Enable or disable WMM power saving mode. 
PS Mode  Power saving modes include AC_BE, AC_BK,