Getnet Router GR-534W User Manual

							 
16 
 
 
Step5 If you are not sure of the SSID available, please log in to the Web page of 
AP, and view the SSID on the Basic Wireless Settings page. For more 
information about the wireless settings, please refer to 5.4 Wireless 
Settings (Gateway Mode). 
 
 
Note: 
After your wireless network card connects to AP successfully, usually, you should 
set the network adapter to be Obtain an IP address automatically. 
 
 
3.5   Log In to the Web Page  
						

							 
17 
Open the browser, and enter http://192.168.1.1/ in the IE address bar. 
 
 
Enter the user name (admin, by default) and the password (admin, by default) on the 
login page.
 
 
 
After clicking the OK button on the login page, you can log in to the Web page   
  
						

							 
18 
4   Quick Start 
4.1   Quick Start in the Bridge Mode 
In the bridge mode, you may connect the LAN interfaces of the GR-534W or other 
wireless devices to a LAN. 
 
 
Click Operation Mode to display the Operation Mode Configuration page. 
 
 
On the Operation Mode Configuration page, choose the Bridge mode, and then 
click the Apply button. 
 
 
Wireless Settings  
						

							 
19 
Click Wireless > Basic to display the Basic Wireless Settings page. 
 
On this page, enable the radio switch and set at least one legal SSID. Make sure that  
						

							 
20 
the wireless devices can connect to the AP. 
After finish the settings, click the Apply button to apply the settings. 
4.2   Quick Start in the Gateway Mode 
In the gateway mode, the GR-534W accesses the Internet by ADSL or cable modem, 
and several users share the IP address provided by the ISP on your network. 
 
 
In the gateway mode: 
  NAT is enabled. 
   WAN interface can be connected to the Internet by STATIC (fixed IP), 
DHCP (Auto config), PPPoE (ADSL), L2TP, and PPTP. 
If you want to configure GR-534W working in gateway mode, do as follows: 
Click Operation Mode to display the Operation Mode Configuration page. 
 
 
On the Operation Mode Configuration page, choose the Gateway mode, and then  
						

							 
21 
click the Apply button. 
4.2.1   System Management 
If you want to set the network time, click Administration > Management to display 
the System Management page. 
  
 
In the table of NTP Settings, choose your time zone, enter the NTP server address, 
and set the NTP synchronization time. 
After finish setting, click the Apply button to apply the settings, and then AP can 
synchronize its time with the network time server. 
4.2.2   LAN Settings 
If you want to change the default IP address of the GR-534W, click the Internet > 
LAN to display the Local Area Netw ork (LAN) Settings page.  
						

							 
22 
 
 
On this page, you may manually enter the IP address. It is recommended you keep 
the default setting.   
If you do not know the IP address of the DNS server provided by the ISP, please  
						

							 
23 
enable DNS Proxy and change your network setting. Assign the IP address of current 
DNS server to be the LAN IP address of the GR-534W. If you use P2P software, the 
UPnP function needs to be enabled. 
After finishing setting, click the Apply button to apply the settings. 
4.2.3   WAN Settings 
Click Internet > WAN to display the Wide Area Network (WAN) Settings page. 
 
 
This page provides 5 types of WAN connection modes, including STATIC (fixed IP), 
DHCP (Auto config), PPPoE (ADSL), L2TP, and PPTP. On this page, select the 
proper WAN connection type according to the connection types provided by your ISP, 
and configure its parameters. 
After finishing setting, click the Apply button to apply the settings. 
4.2.4   Wireless Settings 
Click Wireless > Basic to display the Basic Wireless Settings page.  
						

							 
24 
 
 
On this page, it provides 4 types of network modes, including 11 b/g/n mixed mode, 
11 b/g mixed mode, 11 b only, and 11g only. The default network mode is 11 b/g/n 
mixed mode. You can set the SSID according to your actual application. The 
maximum character length is up to 32 characters.
 The default channel is channel 11.  
						

							 
25 
After finishing setting, click the Apply button to apply the settings. 
4.2.5   Wireless Security 
Click Wireless > Security to display the Wireless Security/Encryption Settings 
page. 
 
 
On this page, you can set the security mode. The security modes include Open, 
Shared, WEPAUTO, WPA-Enterprise, WPA-PSK, WPA2-Enterprise, WPA2-PSK, 
WPA-PSK/WPA2-PSK, WPA1/WPA2-Enterprise, and Dynamic WEP 802.1X. 
After finishing setting, click the Apply button to apply the settings. 
4.3   Quick Start in the WISP Mode 
In the WISP (Wireless Internet Service Provider) mode, GR-534W works as a station, 
and it can connect to another AP. All the Ethernet interfaces can access the Internet 
by wireless routing. Several GR-534Ws can realize more flexible network structure. 
 
Click Operation Mode to display the Operation Mode Configuration page.