Getnet Router GR-724W User Manual

4 
1-3 System Requirements 
 
z  Internet connection, provided by xDSL or cable modem with a RJ-45 
Ethernet port. 
z  Computer or network devices with wired or wireless network interface 
card. 
z  Web browser (Microsoft Internet Explorer 4.0 or above, Netscape 
Navigator 4.7 or above, Opera web browser, or Safari web browser). 
z  An available AC power socket (100 – 240V, 50/60Hz) 
  

5 
1-4 Package Contents 
 
Before you starting to use this router, please check if there’s anything 
missing in the package, and contact your dealer of purchase to claim for 
missing items: 
 
□ Router with Antennas (main body, 2 pcs)………………………… 1 
□ Quick installation guide (1 pcs) …………………………………  2 
□ CDROM (with multi-languages setup wizard, multi-languages Quick 
installation guide and User manual )(1 pcs) ……………………..  3 
□ 12V 0.5A power adapter (1 pcs)……………………………….....  4 
□ Ethernet Cable (1...

6 
1-5 Familiar with your new wireless broadband router 
 
Front Panel 
 
LED Name Light Status Description 
PWR  On  Router is switched on and correctly powered. 
WLAN On  Wireless WPS function is enabled. 
Off  Wireless network is switched off. 
Flashing  Wireless LAN activity (transferring or 
receiving data). 
WA N  
LNK/ACT On  WAN port is connected. Off  WAN port is not connected. 
Flashing  WAN activity (transferring or receiving data).
LAN 1-4 
LNK/ACT On  LAN port is connected. Off  LAN port is...

7 
Back Panel 
 
 
 
Item Name Description 
Antenna  It is 3dBi dipole antenna. 
Radio ON/OFF  Switch the button to activate or deactivate the wireless functions. 
Reset / WPS  Reset the router to factory default settings (clear all settings) or 
start WPS function. Press this button and hold for 10 seconds to 
restore all settings to factory defaults, and press this button for less 
than 5 seconds to start WPS function. 
1 - 4  Local Area Network (LAN) ports 1 to 4. 
WAN  Wide Area Network (WAN /...

8 
Chapter II: System and Network Setup 
 
2-1 Build network connection 
 
Please follow the following instruction to build the network connection 
between your new WIRELESS router and your computers, network 
devices: 
 
1. Connect your xDSL / cable modem to the WAN port of router by 
Ethernet cable.   
 
 
2. Connect all your computers, network devices (network-enabled 
consumer devices other than computers, like game console, or switch / 
hub) to the LAN port of the router. 
 
  

9 
3. Connect the A/C power adapter to the wall socket, and then connect it 
to the ‘Power’ socket of the router. 
 
 
 
4. Please check all LEDs on the front panel. ‘PWR’ LED should be 
steadily on, WAN and LAN LEDs should be on if the computer / 
network device connected to the respective port of the router is 
powered on and correctly connected. If PWD LED is not on, or any 
LED you expected is not on, please recheck the cabling, or jump to 
‘4-2 Troubleshooting’ for possible reasons and solution.  

10 
2-2 Connecting to wireless broadband router by web browser 
 
  After the network connection is built, the next step you should do is 
setup the router with proper network parameters, so it can work properly 
in your network environment. 
 
  Before you can connect to the router and start configuration 
procedures, your computer must be able to get an IP address 
automatically (use dynamic IP address). If it’s set to use static IP address, 
or you’re unsure, please follow the following instructions...

11 
 
 
2. Select ‘Obtain an IP address from a DHCP server’ and then click ‘OK’.   
  

12 
 
 
 
 
2-2-2Windows 2000 IP address setup: 
 
1. Click ‘Start’ button (it should be located at lower-left corner of your 
computer), then click control panel. Double-click Network and Dial-up 
Connections icon; click Local Area Connection, and Local Area 
Connection Properties window will appear. Select ‘Internet Protocol 
(TCP/IP)’ and then click ‘Properties’   
  

13 
 
 
2. Select ‘Obtain an IP address automatically’ and ‘Obtain DNS server 
address automatically’, then click ‘OK’.