Honeywell 1300g2 Owners Manual

							6 - 45
Code 49

Code 49
Code 49 Message Length
Scan the bar codes below to change the message length.  Refer to Message 
Lengthon page 6-2 for additional information.    Minimum and Maximum
lengths = 1-81.   Minimum Default = 1, Maximum Default = 81.
On
* Off
Minimum Message Length
Maximum Message Length 
						

							6 - 46
Trioptic Code
Trioptic Code is used for labeling magnetic storage media.
GS1 Emulation
The scanner can automatically format the output from any GS1 data carrier to 
emulate what would be encoded in an equivalent GS1-128 or GS1 DataBar  
symbol.  GS1 data carriers include UPC-A and UPC-E, EAN-13 and EAN-8, 
ITF-14, GS1-128, and GS1-128 DataBar and GS1Composites.  If GS1-128 
Emulation is selected, the AIM Symbology Identifier will be reported as “]C1”.  If 
GS1 DataBar Emulation is selected, the AIM Symbology Identifier will be 
reported as “]e0.”  Any application that accepts GS1 data can be simplified 
since it only needs to recognize one data carrier type.  Default = GS1 Emulation 
Off.
On
Off
GS1 Data Bar Emulation
GS1-128 Emulation
* GS1 Emulation Off 
						

							6 - 47
Label Code
The standard Label Code is used in library situations.  Default = Off.
On
* Off 
						

							6 - 48 
						

							7 - 1
7
Interface Keys
Keyboard Function Relationships
The following Keyboard Function Code, Hex/ASCII Value, and Full ASCII 
“CTRL”+  relationships apply to all terminals that can be used with the scanner.  
Refer to Windows Mode Control + X Mode On (page 2-20) to enable Control + 
ASCII mode.
Function Code HEX/ASCII Value Full ASCII “CTRL” +
NUL 00 2
SOH 01 A
STX 02 B
ETX 03 C
EOT 04 D
ENQ 05 E
ACK 06 F
BEL 07 G
BS 08 H
HT 09 I
LF 0A J
VT 0B K
FF 0C L
CR 0D M
SO 0E N
SI 0F O
DLE 10 P
DC1 11 Q
DC2 12 R
DC3 13 S
DC4 14 T
NAK 15 U
SYN 16 V
ETB 17 W
CAN 18 X
EM 19 Y
SUB 1A Z
ESC 1B [
FS 1C \
GS 1D ]
RS 1E 6
US 1F - 
						

							7 - 2
Supported Interface Keys
ASCIIHEX
IBM AT/XT and 
PS/2 Compatibles, 
WYSE PC/AT
Supported Keys
NUL 00 Reserved
SOH 01 Enter (KP)
STX 02 Cap Lock
ETX 03 ALT make
EOT 04 ALT break
ENQ 05 CTRL make
ACK 06 CTRL break
BEL 07 CR/Enter
BS 08 Reserved
HT 09 Tab
LF 0A Reserved
VT 0B Tab
FF 0C Delete
CR 0D CR/Enter
SO 0E Insert
SI 0F Escape
DLE 10 F11
DC1 11 Home
DC2 12 Print
DC3 13 Back Space
DC4 14 Back Tab
NAK 15 F12
SYN 16 F1
ETB 17 F2
CAN 18 F3
EM 19 F4
SUB 1A F5
ESC 1B F6
FS 1C F7
GS 1D F8
RS 1E F9
US 1F F10
* IBM 3191/92, 3471/72, 3196/97, 3476/77,
Telex (all models) 
						

							7 - 3
Supported Interface Keys
ASCIIHEX
Apple Mac/iMac 
Supported Keys
NUL 00 Reserved
SOH 01 Enter/Numpad Enter
STX 02 CAPS
ETX 03 ALT make
EOT 04 ALT break
ENQ 05 CNTRL make
ACK 06 CNTRL break
BEL 07 RETURN
BS 08 APPLE make
HT 09 TAB
LF 0A APPLE break
VT 0B TAB
FF 0C Del
CR 0D RETURN
SO 0E Ins Help
SI 0F ESC
DLE 10 F11
DC1 11 Home
DC2 12 Prnt Scrn
DC3 13 BACKSPACE
DC4 14 LSHIFT TAB
NAK 15 F12
SYN 16 F1
ETB 17 F2
CAN 18 F3
EM 19 F4
SUB 1A F5
ESC 1B F6
FS 1C F7
GS 1D F8
RS 1E F9
US 1F F10
DEL 7F BACKSPACE 
						

							7 - 4 
						

							8 - 1
8
Utilities
To Add a Test Code I.D. Prefix to All Symbologies
This selection allows you to turn on transmission of a Code I.D. before the 
decoded symbology.  (See the Symbology Charts (page A-1) for the single 
character code that identifies each symbology.)  This action first clears all cur-
rent prefixes, then programs a Code I.D. prefix for all symbologies.  This is a 
temporary setting that will be removed when the unit is power cycled.
Show Software Revision
Scan the bar code below to output the current software revision, unit serial num-
ber, and other product information.
Show Data Format
Scan the bar code below to show current data format settings.
EZConfig-Scanning Introduction
EZConfig-Scanning provides a wide range of PC-based programming functions 
that can be performed on a scanner connected to your PCs COM port.  EZCon-
fig-Scanning allows you to download upgrades to the scanners firmware, 
Add Code I.D. Prefix to
All Symbologies (Temporary)
Show Revision
Data Format Settings
DFMBK3?. 
						

							8 - 2
change programmed parameters, and create and print programming bar codes.  
Using EZConfig-Scanning, you can even save/open the programming parame-
ters for a scanner.  This saved file can be e-mailed or, if required, you can cre-
ate a single bar code that contains all the customized programming parameters 
and mail or fax that bar code to any location.  Users in other locations can scan 
the bar code to load in the customized programming. 
To communicate with a scanner, EZConfig-Scanning requires that the PC have 
at least one available serial communication port, or a serial port emulation using 
a physical USB port.  If you are using the serial port and RS232 cable, an exter-
nal power supply is required.  When using a USB serial port emulation, only a 
USB cable is required.
EZConfig-Scanning Operations
The EZConfig-Scanning software performs the following operations:
Scan Data
Scan Data allows you to scan bar codes and display the bar code data 
in a window.  Scan Data lets you send serial commands to the scanner 
and receive scanner response that can be seen in the Scan Data win-
dow.  The data displayed in the Scan Data window can either be saved 
in a file or printed. 
Configure
Configure displays the programming and configuration data of the 
scanner.  The scanners programming and configuration data is 
grouped into different categories.  Each category is displayed as a tree 
item under the Configure tree node in the application explorer.  When 
one of these tree nodes is clicked, the right-hand side is loaded with 
the parameters form belonging to that particular category.  The Con-
figure tree option has all the programming and configuration parame-
ters specified for a scanner.  You can set or modify these parameters 
as required.  You can later write the modified settings to the scanner, 
or save them to a dcf file. 
Installing EZConfig-Scanning from the Web
1. Access the Honeywell web site at www.honeywellaidc.com
2. Click on the Resources tab.  Select Download.
3. Click on the dropdown for Select Product Number and select the 
number of your product.
4. Under Tools and Utilities, click on the listing for EZConfig for 
Scanning.