Honeywell 1300g2 Owners Manual

							3 - 7
Scan the Hands Free Time-Out bar code, then scan the time-out duration 
(from 0-300,000 milliseconds) from the inside back cover, and Save.   Default = 
5,000 ms.
Reread Delay
This sets the time period before the scanner can read the same bar code a sec-
ond time.  Setting a reread delay protects against accidental rereads of the 
same bar code.  Longer delays are effective in minimizing accidental rereads at 
POS (point of sale).  Use shorter delays in applications where repetitive bar 
code scanning is required.  Default = Medium.
Reread Delay only works when in automatic trigger mode or presentation mode 
(see page 3-5).
Hands Free Time-Out
Short (500 ms)
* Medium (750 ms)
Long (1000 ms)
Extra Long (2000 ms) 
						

							3 - 8
User-Specified Reread Delay
If you want to set your own length for the reread delay, scan the bar code below, 
then set the delay (from 0-30,000 milliseconds) by scanning digits from the 
inside back cover, then scanning Save. 
Centering
Use Centering to narrow the scanner’s field of view to make sure the scanner 
reads only those bar codes intended by the user.  For instance, if multiple codes 
are placed closely together, centering will insure that only the desired codes are 
read.
If a bar code is not touched by a predefined window, it will not be decoded or 
output by the scanner.  If centering is turned on by scanning Centering On, the 
scanner only reads codes that pass through the centering window you specify 
using the Left of Centering Window, or Right of Centering Window bar 
codes.  
In the example below, the red line is the full scanner field of view and the white 
boxed area is the centering window.  The centering window has been set to 
20% left and 30% right, as shown in the legend at the bottom.  Since Bar Code 
1 passes through the centering window, it will be read.  Bar Code 2 does not 
pass through the centering window, so it will not be read.
Scan Centering On, then scan one of the following bar codes to change the left 
or right of the centering window.  Then scan the percent you want to shift the 
centering window using digits on the inside back cover of this manual.  Scan 
Save.   Default Centering = 40% for Left, 60% for Right.
User-Specified Reread Delay
0 %      1 0 %        2 0 %      3 0 %        4 0 %      5 0 %        6 0 %       7 0 %        8 0 %       9 0 %     1 0 0 %
Bar Code 1 Bar Code 2 
						

							3 - 9
Left of Centering Window
Right of Centering Window
* Centering Off Centering On 
						

							3 - 10
Output Sequence Overview
Output Sequence Editor
This programming selection allows you to program the scanner to output data 
(when scanning more than one symbol) in whatever order your application 
requires, regardless of the order in which the bar codes are scanned.  Reading 
the Default Sequence symbol programs the scanner to the Universal values, 
shown below.  These are the defaults.  Be certain you want to delete or clear all 
formats before you read the Default Sequence symbol.
Note: To make Output Sequence Editor selections, you’ll need to know the 
code I.D., code length, and character match(es) your application 
requires.  Use the Alphanumeric symbols (inside back cover) to read 
these options.
Note: You must hold the trigger while reading each bar code in a sequence.
To Add an Output Sequence
1. Scan the Enter Sequence symbol (see Require Output Sequence, page 3-
13).
2.Code I.D.
On the Symbology Chartson page A-1, find the symbology to which you 
want to apply the output sequence format.  Locate the Hex value for that 
symbology and scan the 2 digit hex value from the Programming Chart 
(inside back cover).
3.Length
Specify what length (up to 9999 characters) of data output will be acceptable 
for this symbology.  Scan the four digit data length from the Programming 
Chart.  (Note:  50 characters is entered as 0050.  9999 is a universal num-
ber, indicating all lengths.)  When calculating the length, you must count any 
programmed prefixes, suffixes, or formatted characters as part of the length 
(unless using 9999). 
4.Character Match Sequences
On the ASCII Conversion Chart (Code Page 1252), page A-3, find the Hex 
value that represents the character(s) you want to match.  Use the Program-
ming Chart to read the alphanumeric combination that represents the ASCII 
characters.  (99 is the Universal number, indicating all characters.)
5.End Output Sequence Editor
Scan F F to enter an Output Sequence for an additional symbology, or Save 
to save your entries.
Other Programming Selections
Discard 
This exits without saving any Output Sequence changes. 
						

							3 - 11
Output Sequence Editor   
Output Sequence Example
In this example, you are scanning Code 93, Code 128, and Code 39 barcodes, 
but you want the image scanner to output Code 39 1st, Code 128 2nd, and 
Code 93 3rd, as shown below.
Note: Code 93 must be enabled to use this example.
You would set up the sequence editor with the following command line:
SEQBLK62999941FF6A999942FF69999943FF
The breakdown of the command line is shown below:
SEQBLKsequence editor start command
62 code identifier for Code 39
9999 code length that must match for Code 39, 9999 = all lengths
41 start character match for Code 39, 41h = “A”
FF termination string for first code
6A code identifier for Code 128
9999 code length that must match for Code 128, 9999 = all lengths
Enter Sequence
Default Sequence
A - Code 39
B - Code 128
C - Code 93 
						

							3 - 12
42 start character match for Code 128, 42h = “B”
FF termination string for second code
69 code identifier for Code 93
9999 code length that must match for Code 93, 9999 = all lengths
43 start character match for Code 93, 43h = “C”
FF termination string for third code
To program the previous example using specific lengths, you would have to 
count any programmed prefixes, suffixes, or formatted characters as part of the 
length.  If you use the example on page 3-11, but assume a  suffix and 
specific code lengths, you would use the following command line:
SEQBLK62001241FF6A001342FF69001243FF
The breakdown of the command line is shown below:
SEQBLK sequence editor start command
62 code identifier for Code 39
0012 A - Code 39 sample length (11) plus CR suffix (1) = 12
41 start character match for Code 39, 41h = “A”
FF termination string for first code
6A code identifier for Code 128
0013 B - Code 128 sample length (12) plus CR suffix (1) = 13
42 start character match for Code 128, 42h = “B”
FF termination string for second code
69 code identifier for Code 93
0012 C - Code 93 sample length (11) plus CR suffix (1) = 12
43 start character match for Code 93, 43h = “C”
FF termination string for third code 
						

							3 - 13
Output Sequence Editor   
Require Output Sequence
When an output sequence is Required, all output data must conform to an 
edited sequence or the image scanner will not transmit the output data to the 
host device.  When it’s On/Not Required, the image scanner will attempt to get 
the output data to conform to an edited sequence, but if it cannot, the image 
scanner transmits all output data to the host device as is.
When the output sequence is Off, the barcode data is output to the host as the 
image scanner decodes it.  
Note: This selection is unavailable when the Multiple Symbols Selection is 
turned on.
Multiple Symbols
When this programming selection is turned On, it allows you to read multiple 
symbols with a single pull of the scanner’s trigger.  If you press and hold the trig-
ger, aiming the scanner at a series of symbols, it  reads unique symbols once, 
Enter Sequence
Default Sequence
 Required
 On/Not Required
 *Off 
						

							3 - 14
beeping (if turned on) for each read.  The scanner attempts to find and decode 
new symbols as long as the trigger is pulled.  When this programming selection 
is turned Off, the scanner will only read the symbol closest to the aiming beam.
No Read
With No Read turned On, the scanner sends an “NR” to the host if you pull and 
release the trigger without reading a code (e.g., bad bar code).  If No Read is 
turned Off, the “NR” will not be sent to the host.
If you want a different notation than “NR,” for example, “Error,” or “Bad Code,” 
you can edit the output message using the Data Formatter (page 5-14).  The 
hex code for the No Read symbol is 9C.  
On
* Off
On
* Off 
						

							3 - 15
Video Reverse
Video Reverse is used to allow the scanner to read bar codes that are inverted.  
The “Off ” bar code below is an example of this type of bar code.
Note:  If additional menuing is required, Video Reverse must be disabled to read 
the menu bar codes and then re-enabled after menuing is completed.
On
VIDREV0REV.
* Off 
						

							3 - 16