HP Ac100 User Manual

							 
20
Connecting the camera to a high-definition TV:                                       
 
Connect the camera to a high-definition TV with a HD cable (as shown below , not included). In a few seconds, 
the playback UI will be displayed on the TV.    Use the Action Cam to select the recorded video or photos to 
playback on the TV. 
 
  
 
 
 
 
 
  
 
 
Connection diagram 
Signal transmission  
						

							 
21
Application on the personal computer                                               
 
Connect the Action Cam to the PC or laptop using the supplied USB. to a PC 
The Action Cam is provided with the plug and play function . Connect the Action Cam to the computer with 
USB line under turning-on state, then it will be switched into the movable hard disk mode. 
Icon of movable disk will appear on the window of “my computer”. The photos you have taken can be 
saved in the removable disk under the file folder I:\ jpg (“I” is the removable disk of the camera). Your 
video files will be saved under the folder of I:\video.Note: if movable disk function is used in windows 
2000 or windows operating system with a higher edition, it is unnecessary to install drivers. 
Remote Control Overview
                                                               
1  Keys of remote control 
The keys on the remote control are shown in the right figure 
 
 
 
 
 
OFF Button 
REC Button
 
SNAPButton 
Signal transmission port  
						

							 
22
2  Use of the remote control: 
Using the remote control will help you with video recording, taking photos and shutting down 
without operating the Action Cam directly. While using the remote control, face the signal 
transmitter port toward the infrared signal receiver of the Action Cam as shown below. Record 
videos, take photos or shut down the camera by pressing the corresponding buttons on the remote 
control.
 
 
 
 
 
 
 
 
Infrared receiver light  
						

							 
23
Waterproof Case Using Notice                                                    
 
 Before closing the waterproof case, keep the housing’s rubber seal clean and free of debris to reduce the 
risk of a leak. Test the waterproof case by closing the case without inserting the Action Cam. Submerse 
the case completely in water for about a minute. Remove the case from the water, dry off its exterior 
with a towel, then open the case. If the entire interior is dry, the case is safe for use under water. 
 Remember to put the Action Cam in your desired recording mide before inserting into the waterproof case. 
If needed, use the remote control to switch between photo and video mode. 
 After every use in salt water please rinse the outside of the housing with tap water and dry. This will help 
reduce the risk of corrosion to the hinge pin and salt buildup in the seal, which can cause failure. 
 To clean the seal, rinse in fresh water and shake dry (drying with a cloth may cause lint to compromise the 
seal). Re-install the seal into the grooves in the backdoor of the housing.    
						

							 
24
Technical parameters                                                            
 
Image sensor  5M pixels (CMOS) Function modes  Video recording, photo, removable disk Camera lens  F3.1 f=2.9mm Digital zooming  4X Shutter Electronic shutter LCD display screen  2.4-inch touch screen Image resolution  12M (4000 × 3000), 10M (3648x2736), 8 M (3264x2448), 5M (2560×1920) Video resolution HD: 1280x720 (60 frames/sec.) HD: 1280x720 (30 frames/sec), FHD: 1920x1080 
(30 frames/sec) White balance  Automatic   Exposure Automatic 
Video AVI 
File formats 
Photo JPEG Storage medium  MicroSD card (Supporting up to 32GB),( without build-in flash memory) USB interface  High-speed USB 2.0 interface Power Supply  Built-in 3.7V rechargeable lithium Dimensions 
(width x height x depth) 74mm(W) x 52mm (H) x 33mm (D) 
2.9 x 2.1 x 1.3 Weight Approx. 78g   
						

							 
25
Standard packaging