HP Color Laserjet 5 Manual

							Replacing the Toner Collection Kit
When the message 14.5 REPLACE COLLECTION
KIT appears on the printer display, change the
toner collection box and filter.
Note
Use only maintenance units designed and
labeled for the HP Color LaserJet 5/5M
printer. Other maintenance units may
damage your printer or result in inferior print
quality.
Note
If the 14.5 REPLACE COLLECTION KIT message
appears, your printer will not work until you
perform the following procedure.  Keep an
extra toner collection kit on hand to avoid
printer down time.
1Turn the printer off (button out).
2When the fan turns off (5 minutes),
unplug the printer.
3Replace the toner collection box:
aOpen the left side cover of the printer
by grasping its bottom edge and lifting
it up.
bPull out the toner collection box
horizontally and set it aside for disposal.
For proper printer operation, do not
re-use the toner collection box. To
prevent toner spills, keep the toner
box horizontal when handling it.
Handle the toner collection box
carefully to prevent damaging it. Do
not incinerate the used collection box. 
à à
3a
3b
2
1
6
Maintaining
Your Printer
ENMaintaining Your Printer  6-11 
						

							cRemove the new toner collection box
from its packaging.
dSlide the new toner collection box into
the printer until it is flush with the
side of the print drum.
eClose the printer side cover.
à à
3e
3c
3d
6-12  Maintaining Your PrinterEN 
						

							4Replace the ozone filter
aPress the top release button, then
open the top cover.
bGrasp the filter by its two top corners,
then slide it up and out of the printer.
Set the filter aside for disposal.
Caution
Do not drop the new filter. The filter may be
permanently damaged if dropped against a
hard surface.
cRemove the new filter from its
packaging.
dGrasping the two top corners of the
new filter, slide it down into the
printer.
The filter can be installed in any
direction with either face out.
à à
4d
4b
4c
4a
6
Maintaining
Your Printer
ENMaintaining Your Printer  6-13 
						

							5Close the top cover.
6Plug in the printer.
7Turn the printer ON (button in).
The printer goes through a brief self test
sequence, then returns on line with 00
PCL (or POSTSCRIPT) READY on the printer
display.
5
6
7
6-14  Maintaining Your PrinterEN 
						

							Replacing the Coating Kit
When the message 14.6 REPLACE COATING KIT
appears on the printer display, change the
coating roller and cleaning roller. Print
quality will degrade until the kit is replaced.
Note
Use only maintenance units designed and
labeled for the HP Color LaserJet 5/5M
printer. Other maintenance units may
damage your printer or result in inferior print
quality.
1Turn the printer off (button out).
WARNING!
Wait thirty minutes for the fuser to cool down
before removing the coating roller. Continuing
before the fuser has cooled down may result in
severe burns.
2Unplug the printer.
3Replace the coating roller.
Caution
Do not expose the print drum to direct light
for extended periods of time. Exposure to light
can permanently damage the drum.
aPress the top cover release button,
then open the top cover.
à à
2
1
3a
6
Maintaining
Your Printer
ENMaintaining Your Printer  6-15 
						

							bLocate the coating roller on the fuser
(A).
cRaise the handles on the cleaning
roller and remove it from the printer.
Set the coating roller aside and
remember to dispose of it responsibly.
WARNING!
Make sure the fuser has cooled down before
using the fuser cleaning tool. Continuing
before the fuser has cooled down may result in
severe burns.
dRemove the cleaning roller from its
packaging.
eWith the handles on top and the dot to
the right, install the new cleaning
roller.
à à
3d
1900C
3740F
3e
3b
1900C
3740F
3c
1900C
3740F
6-16  Maintaining Your PrinterEN 
						

							fPush the cleaning roller down until it
clicks into place horizontally, then fold
down the handles.
4Replace the cleaning roller.
aLocate the coating roller on the fuser
(B).
à à
4a
1900C
3740F
1900C
3740F
3f
6
Maintaining
Your Printer
ENMaintaining Your Printer  6-17 
						

							bRaise the handles on the coating roller
and remove it from the printer. Set
the cleaning roller aside and
remember to dispose of it responsibly.
cRemove the new cleaning roller from
its packaging.
dWith the handles on top and the
triangle alignment mark to the right,
install the new coating roller.
ePush the coating roller down until it
clicks into place horizontally, then fold
down the handles.
à à
4e
1900C
3740F
4c
4b
1900C
3740F
4d
1900C
3740F
6-18  Maintaining Your PrinterEN 
						

							5Close the top cover.
6Plug in the printer.
7Turn the printer ON (button in).
The printer goes through a brief self test
sequence, then returns on line with 00
PCL (or POSTSCRIPT) READY on the printer
display.
5
6
7
6
Maintaining
Your Printer
ENMaintaining Your Printer  6-19 
						

							Replacing the Black Developer
Replace the black developer when the
message 19.1 BLACK DEVEL USER MAINTENANCE
appears on the printer display. Print quality
will degrade until the unit is replaced. To
verify the life remaining on other
maintenance units, print a self test page.
Note
Use only maintenance units designed and
labeled for the HP Color LaserJet 5/5M
printer. Other maintenance units may
damage your printer or result in inferior print
quality.
1Turn the printer off (button out).
2When the fan turns off (5 minutes),
unplug the printer.
3Press the top cover release button, then
open the top cover.
4Open the left side cover of the printer by
grasping its lower edge and lifting it up.
à à
4 3 2
1
12
6-20  Maintaining Your PrinterEN