Indesit Iwc 5125 Instructions For Use

							1
GBContents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Description of the washing machine 
and starting a wash cycle, 4-5
Control panel
Indicator lights
Starting a wash cycle
Wash cycles, 6
Table of wash cycles
Personalisation, 7
Setting the temperature
Setting the spin speed
Functions
Detergents and laundry, 8
Detergent dispenser drawer
Bleach cycle
Preparing the laundry
Garments requiring special care
Load balancing system
Precautions and tips, 9
General safety
Disposal
Care and maintenance, 10
Cutting off the water or electricity supply
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Troubleshooting, 11
Service, 12
IWC 5125
Instructions for use
WASHING MACHINE
English,1
GB
Nederlands,25Français,13
NLF
  
						

							2
GB
Installation
! This instruction manual should be kept in a safe place for 
future reference. If the washing machine is sold, transferred 
or moved, make sure that the instruction manual remains 
with the machine so that the new owner is able to familiari-
se himself/herself with its operation and features.
! Read these instructions carefully: they contain vital infor-
mation relating to the safe installation and operation of the 
appliance.
Unpacking and levelling
Unpacking
1. Remove the washing machine from its packaging.
2. Make sure that the washing machine has not been 
damaged during the transportation process. If it has been 
damaged, contact the retailer and do not proceed any 
further with the installation process.
3. Remove the 3 protective 
screws (used during tran-
sportation) and the rubber 
washer with the correspon-
ding spacer, located on the 
rear part of the appliance 
(see figure).
4. Close off the holes using the plastic plugs provided.
5. Keep all the parts in a safe place: you will need them 
again if the washing machine needs to be moved to ano-
ther location.
! Packaging materials should not be used as toys for 
children.
Levelling
1. Install the washing machine on a flat sturdy floor, without 
resting it up against walls, furniture cabinets or anything 
else.
2. If the floor is not perfectly 
level, compensate for any 
unevenness by tightening 
or loosening the adjusta-
ble front feet (see figure); 
the angle of inclination, 
measured in relation to the 
worktop, must not exceed 
2°.
Levelling the machine correctly will provide it with stability, 
help to avoid vibrations and excessive noise and prevent it 
from shifting while it is operating. If it is placed on carpet or 
a rug, adjust the feet in such a way as to allow a sufficient 
ventilation space underneath the washing machine.
Connecting the electricity and water 
supplies
Connecting the water inlet hose
1. Connect the supply pipe 
by screwing it to a cold 
water tab using a ¾ gas 
threaded connection (see 
figure). 
Before performing the con-
nection, allow the water to 
run freely until it is perfectly 
clear.
2. Connect the inlet hose 
to the washing machine by 
screwing it onto the corre-
sponding water inlet of the 
appliance, which is situa-
ted on the top right-hand 
side of the rear part of the 
appliance (see figure).
3. Make sure that the hose is not folded over or bent.
! The water pressure at the tap must fall within the values 
indicated in the Technical details table (see next page).
! If the inlet hose is not long enough, contact a specialised 
shop or an authorised technician.
! Never use second-hand hoses.
! Use the ones supplied with the machine.
   
						

							3
GB
65 - 100 cm
Connecting the drain hose
 
Connect the drain hose, 
without bending it, to a drai-
nage duct or a wall drain 
located at a height between 
65 and 100 cm from the 
floor; 
alternatively, rest it on 
the side of a washbasin 
or bathtub, fastening the 
duct supplied to the tap 
(see figure). The free end 
of the hose should not be 
underwater.
! We advise against the use of hose extensions; if it is 
absolutely necessary, the extension must have the same 
diameter as the original hose and must not exceed 150 cm 
in length.
Electrical connections
Before plugging the appliance into the electricity socket, 
make sure that: 
•	 the	socket	is	earthed	and	complies	with	all	applicable	
laws;
•	 the	socket	is	able	to	withstand	the	maximum	power	load	
of the appliance as indicated in the Technical data table 
(see opposite);
•	 the	power	supply	voltage	falls	within	the	values	indicated	
in the Technical data table (see opposite);
•	 the	socket	is	compatible	with	the	plug	of	the	washing	
machine. If this is not the case, replace the socket or the 
plug.
! The washing machine must not be installed outdoors, 
even in covered areas. It is extremely dangerous to leave 
the appliance exposed to rain, storms and other weather 
conditions.
! When the washing machine has been installed, the elec-
tricity socket must be within easy reach.
! Do not use extension cords or multiple sockets.
! The cable should not be bent or compressed.
! The power supply cable must only be replaced by autho-
rised technicians.
Warning! The company shall not be held responsible in the 
event that these regulations are not respected.
The first wash cycle
Once the appliance has been installed, and before you use 
it for the first time, run a wash cycle with detergent and no 
laundry, using the wash cycle 2.
Technical data
ModelIWC 5125
Dimensions width 59.5 cm
height 85 cm
depth 52,5 cm
Capacity from 1 to 5 kg 
Electrical 
connections please refer to the technical data plate fixed 
to the machine
Water connection maximum pressure 1 MPa (10 bar)
minimum pressure 0.05 MPa (0.5 bar)
drum capacity 46 litres
Spin speed up to 1200 rotations per minute
Test  
Programmes 
according to 
2010/1061 Programme 2: temperature 60°C and 40°C;
This appliance conforms to the following EC 
Directives:
- 2004/108/CE (Electromagnetic Compatibility)
- 2002/96/EC
- 2006/95/EC (Low Voltage)
  
						

							4
GB
Detergent dispenser drawer: used to dispense 
detergents and washing additives (see “Detergents and 
laundry”).
ON/OFF button: switches the washing machine on and 
off.
WASH CYCLE knob: programmes the wash cycles. Du-
ring the wash cycle, the knob does not move. 
FUNCTION buttons with indicator light: used to select the 
available functions. The indicator light corresponding to the 
selected function will remain lit.
TEMPERATURE knob: sets the temperature or the cold 
wash cycle (see “Personalisation”).
SPIN SPEED knob: sets the spin speed or exclude the 
spin cycle completely (see “Personalisation”).
WASH CYCLE PROGRESS/DELAY TIMER indicator 
lights: used to monitor the progress of the wash cycle.
The illuminated indicator light shows which phase is in 
progress.
If the Delay Timer function has been set, the time remai-
ning until the wash cycle starts will be indicated  (see next 
page).
DOOR LOCKED indicator light: indicates whether the 
door may be opened or not (see next page).
START/PAUSE button with indicator light: starts or tem-
porarily interrupts the wash cycles.
N.B. To pause the wash cycle in progress, press this 
button; the corresponding indicator light will flash orange, 
while the indicator light for the current wash cycle phase 
will remain lit in a fixed manner. If the DOOR LOCKED  
indicator light is switched off, the door may be opened.
To start the wash cycle from the point at which it was inter-
rupted, press this button again.
Standby mode
This washing machine, in compliance with new energy 
saving regulations, is fitted with an automatic standby 
system which is enabled after a few minutes if no activity is 
detected. Press the ON-OFF button briefly and wait for the 
machine to start up again.
Description of the washing 
machine and starting a wash cycle
WASH CYCLE PROGRESS/DELAY TIMER indicator lights
DOOR LOCKED indicator light
START/
PAUSE button with indicator light
Control panel
Detergent dispenser drawer
ON/OFF button
WASH CYCLE knob
TEMPERATURE knob
FUNCTION buttons with indicator lights
SPIN SPEED knob
   
						

							5
GBIndicator lights
The indicator lights provide important information.
This is what they can tell you:
Delayed start
If the DELAY TIMER function has been activated (see “Per-
sonalisation”), after the wash cycle has been started the 
indicator light corresponding to the selected delay period 
will begin to flash:
As time passes, the remaining delay will be displayed and 
the corresponding indicator light will flash:
The set programme will start once the selected time delay 
has expired.
Wash cycle phase indicator lights
Once the desired wash cycle has been selected and has be-
gun, the indicator lights switch on one by one to indicate which 
phase of the cycle is currently in progress.
Function buttons and corresponding indicator lights
When a function is selected, the corresponding indicator 
light will illuminate. 
If the selected function is not compatible with the program-
med wash cycle, the corresponding indicator light will flash 
and the function will not be activated.
If the selected function is not compatible with another 
function which has been selected previously, the indicator 
light corresponding to the first function selected will 
flash and only the second function will be activated; the 
indicator light corresponding to the enabled option will 
remain lit.
 Door locked indicator light
When the indicator light is on, the porthole door is locked 
to prevent it from being opened; make sure the indicator 
light is off before opening the door (wait approximately 3 
minutes). To open the door during a running wash cycle, 
press the START/PAUSE button; the door may be opened 
once the DOOR LOCKED indicator light turns off.
Starting a wash cycle
1. Switch the washing machine on by pressing the ON/OFF button. All indicator lights will switch on for a few \
seconds, then 
they will switch off and the START/PAUSE indicator light will pulse.
2. Load the laundry and close the door.
3. Set the WASH CYCLE knob to the desired programme.
4. Set the washing temperature (see “Personalisation”).
5. Set the spin speed (see “Personalisation”).
6. Measure out the detergent and washing additives (see “Detergents and laundry”).
7. Select the desired functions.
8. Start the wash cycle by pressing the START/PAUSE button and the corresponding indicator light will remain lit in a fixed 
manner, in green.
To cancel the set wash cycle, pause the machine by pressing the START/PAUSE button and select a new cycle.
9. At the end of the wash cycle the  indicator light will switch on. The door can be opened once the DOOR LOC\
KED  
indicator light turns off. Take out your laundry and leave the appliance door ajar to make sure the drum dries completely. 
Switch the washing machine off by pressing the ON/OFF button.
Wash
Rinse
Spin
Drain
End of wash cycle
  
						

							6
GB
Specials wash cycles
Express (wash cycle 10) this wash cycle was designed to wash lightly soiled garments quickly:\
 it lasts just 15 minutes and 
therefore saves both energy and time. By selecting this wash cycle (10 at 30°C), it is possible to wash different fabrics toge-
ther (except for wool and silk items), with a maximum load of 1.5 kg.
Sport Intensive (wash cycle 11) is for washing heavily soiled sports clothing fabrics (tracksuits, shorts, etc.); for best 
results, we recommend not exceeding the maximum load indicated in the “Table of wash cycles”.
Sport Light (wash cycle 12) is for washing lightly soiled sports clothing fabrics (tracksuits, s\
horts, etc.); for best results, 
we recommend not exceeding the maximum load indicated in the “Table of wash cycles”. We recommend using a 
liquid detergent and dosage suitable for a half-load.
Sport Shoes (wash cycle 13) is for washing sports shoes; for best results, do not wash more than 2 pairs simultaneously.
Wash cycles
Table of wash cycles
The cycle duration indicated on the display or instruction manual is an \
estimate based on standard conditions. The actual duration may vary in relation to several factors, such as the temperature and pressure of \
the incoming water, ambient temperature, amount of detergent, load quantity and type, load balancing and any additional options selected.
For all Test Institutes:1) Test wash cycle in compliance with regulation 2010/1061: set wash cycle 2 with a temperature of 60°C and 40°C.2) Long wash cycle for cottons: set wash cycle 2 with a temperature of 40°C.3) Short wash cycle for cottons: set wash cycle 4 with a temperature of 40°C.4) Synthetic program along: set wash cycle 5 with a temperature of 40°C.
Wash cycles
Description of the wash cycleMax. 
temp.  (°C) Max. 
speed  (rpm) Detergents
Max. load (kg)Cycle duration
Prewash WashBleach Fabric 
softener NormalEco 
Time Normal Eco 
Time
Daily
1 Cotton with prewash:  extremely soiled whites.  90°1200 

- 
5-145 -
2 Cotton:  extremely soiled whites.  90°1200 -
 
5-125 -
2 Cotton (1-2):  heavily soiled whites and resistant colours. 60°1200 -
 
5-165 -
2 Cotton (2):  heavily soiled whites and delicate colours. 40°1200 -
 
5-155 -
3 Cotton:  heavily soiled whites and resistant colours. 60° 1200 -
 
53,25120 85
4 Coloured Cottons (3):  lightly soiled whites and delicate colours. 40° 1200 -
 
53,25 8560
5 Synthetics:  heavily soiled resistant colours. 60° 800 -
 
2,5 2100 70
5 Synthetics energetic (4):  heavily soiled resistant colours. 40° 800 -
 
2,5 290 65
6 Synthetics:  lightly soiled delicate colours. 40° 800 -
 
2,5 270 50
Special
7 Wool:  for wool, cashmere, etc. 40°800 -
- 
1-70 -
8 Silk/Curtains:  for garments in silk and viscose, lingerie. 30° 0 -
- 
1-55 -
9 Jeans
40° 800 -
- 
3-60 -
10 Express:
 to refresh lightly soiled garments quickly (not suitable for wool, 
silk and clothes which require washing by hand). 30°
800 -
- 
1,5 -15 -
Sport
11 Sport Intensive
30°600 -
- 
3-85 -
12 Sport Light
30°600 -
- 
3-58 -
13 Special Shoes
30° 600 -
- 
Max. 2 pairs -55 -
Partial wash cycles
Rinse -1200 --

5-40 -
Spin -1200 --- - 5-15 -
Drain -0 --- - 5-2 -
   
						

							7
GBSetting the temperature
Turn the TEMPERATURE knob to set the wash temperature (see Table of wash cycles).
The temperature may be lowered, or even set to a cold wash .
The washing machine will automatically prevent you from selecting a temperature which is higher than the maximum value 
set for each wash cycle.
Setting the spin speed
Turn the SPIN SPEED knob to set the spin speed for the selected wash cycle.\
 
The maximum spin speeds available for each wash cycle are as follows:
Wash cycles Maximum spin speed
Cottons   1200 rpm
Synthetics 800 rpm
Wool   800 rpm
Silk   drain only
The spin speed may be lowered, or the spin cycle can be excluded altogether by selecting the symbol\
 .
The washing machine will automatically prevent you from selecting a spin speed which is higher than the maximum speed 
set for each wash cycle.
Functions
The various wash functions available with this washing machine will help\
 to achieve the desired results, every time.
To activate the functions:
1. Press the button corresponding to the desired function;
2. the function is enabled when the corresponding indicator light is illuminated.
Note: If the indicator light flashes rapidly, this signals that this particular function may not be selected in conj\
unction with the 
selected wash cycle.
Selecting this option enables you to suitably adjust drum rotation, temperature and water to a reduced load of lightly soiled 
cotton and synthetic fabrics (refer to the “Table of wash cycles”). “” enables you to wash in less time thereby saving 
water and electricity. We suggest using a liquid detergent suitably measured out to the load quantity. 
! This function may not be used in conjunction with wash cycles 1, 2, 7, 8, 9, 10, 11, 12, 13, , , .
 Stain removal
Bleaching cycle designed to remove the toughest stains. Please remember to pour the bleach into extra compartment 4 (see 
“Bleach cycle”).
! This function may not be used in conjunction with wash cycles 1, 7, 8, 9, 10, 11, 12, 13, , . 
 Extra rinse
By selecting this option, the efficiency of the rinse is increased and optimal detergent removal is guaranteed. It is particularly 
useful for sensitive skin.
! This function may not be used in conjunction with wash cycles 10, , .
 Delay timer
This timer delays the start time of the wash cycle by up to 12 hours.
Press the button repeatedly until the indicator light corresponding to the desired delay time switches on. The fifth time the button 
is pressed, the function will be disabled.
N.B. Once the START/PAUSE button has been pressed, the delay time can only be modified by decreasing it until launching 
the set programme.
! This option is enabled with all programmes.
Personalisation
  
						

							8
GB
Detergents and laundry
Detergent dispenser drawer
Good washing results also depend on the correct dose of 
detergent: adding too much detergent will not necessa-
rily result in a more efficient wash, and may in fact cause 
build up on the inside of your appliance and contribute to 
environmental pollution.
! Do not use hand washing detergents because these 
create too much foam.
Open the detergent di-
spenser drawer and pour 
in the detergent or washing 
additive, as follows.
ompartment 1: Pre-wash detergent (powder)
Before pouring in the detergent, make sure that extra com-
partment 4 has been removed.
compartment 2: Detergent for the wash cycle 
(powder or liquid)
Liquid detergent should only be poured in immediately 
prior to the start of the wash cycle.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid.
extra compartment 4: Bleach
Bleach cycle
! Traditional bleach should be used on sturdy white fa-
brics, and delicate bleach for coloured fabrics, synthetics 
and for wool.
This option is particularly 
useful for the removal of 
stubborn stains. Place extra 
compartment 4 (supplied) 
into compartment 1. 
When pouring in the 
bleach, be careful not to 
exceed the “max” level 
marked on the central pivot 
(see figure).
To run the bleach cycle on its own, pour the bleach into extra 
compartment 4, set the “Rinse”  programme and activate 
the “Stain removal”  option. 
To bleach during a wash cycle, pour in the detergent and 
any fabric softener you wish to use, set the desired wash 
cycle and enable the “Stain removal”  option.
The use of extra compartment 4 excludes the “Pre-wash” 
option.
12 3
4
Preparing the laundry
•	Divide	the	laundry	according	to:
 
- the type of fabric/the symbol on the label
 - the colours: separate coloured garments from whites.
•	Empty	all	garment	pockets	and	check	the	buttons.
•	Do	not	exceed	the	listed	values,	which	refer	to	the	weight	
of the laundry when dry:
 Durable fabrics: max. 5 kg
 Synthetic fabrics: max. 2,5 kg
 Delicate fabrics: max. 2 kg
 Wool: max. 1 kg 
Silk: max. 1 kg
How much does your laundry weigh?
  1 sheet 400-500 g
 1 pillow case 150-200 g
 1 tablecloth 400-500 g
 1 bathrobe 900-1200 g
 1 towel 150-250 g
Garments requiring special care
Wool: all wool garments can be washed using programme 
7, even those carrying the “hand-wash only”  label. For 
best results, use special detergents and do not exceed 1 
kg of laundry.
Silk: use special wash cycle 8 to wash all silk garments. 
We recommend the use of special detergent which has 
been designed to wash delicate clothes.
Curtains: fold curtains and place them in a pillow case or 
mesh bag. Use wash cycle 8.
Jeans: Turn garments inside-out before washing and use 
a liquid detergent. Use programme 9.
Load balancing system
Before every spin cycle, to avoid excessive vibrations  and 
to distribute the load in a uniform manner, the drum rotates 
continuously at a speed which is slightly greater than the 
washing rotation speed. If, after several attempts, the load 
is not balanced correctly, the machine spins at a reduced 
spin speed. If the load is excessively unbalanced, the 
washing machine performs the distribution process instead 
of spinning. To encourage improved load distribution and 
balance, we recommend small and large garments are 
mixed in the load.
   
						

							9
GB
Precautions and tips
! This washing machine was designed and constructed in 
accordance with international safety regulations. The fol-
lowing information is provided for safety reasons and must 
therefore be read carefully.
General safety
•	 This	appliance	was	designed	for	domestic	use	only.
•	 The	washing 	machine 	must 	only 	be 	used 	by 	adults, 	in 	accor-
dance with the instructions provided in this manual.
•	 Do	not	touch	the	machine	when	barefoot	or	with	wet	or	
damp hands or feet.
•	 Do	not	pull	on	the	power	supply	cable	when	unplugging	
the appliance from the electricity socket. Hold the plug 
and pull. 
•	 Do	not	open	the	detergent	dispenser	drawer	while	the	
machine is in operation.
•	 Do	not	touch	the	drained	water	as	it	may	reach	extreme-
ly high temperatures. 
•	 Never	force	the	porthole	door.	This	could	damage	the	
safety lock mechanism designed to prevent accidental 
opening.
•	 If	the	appliance	breaks	down,	do	not	under	any	circum-
stances access the internal mechanisms in an attempt 
to repair it yourself.
•	 Always	keep	children	well	away	from	the	appliance	while	
it is operating.
•	 The 	door 	can 	become 	quite 	hot 	during 	the 	wash 	cycle.
•	 If	the	appliance	has	to	be	moved,	work	in	a	group	of	two	
or three people and handle it with the utmost care. Never 
try to do this alone, because the appliance is very heavy.
•	 Before	loading	laundry	into	the	washing	machine,	make	
sure the drum is empty.
Disposal
•	 Disposing	of	the	packaging	materials:	observe	local	
regulations so that the packaging may be re-used.
•	 The 	European 	Directive 	2002/96/EC 	on 	Waste 	Electrical	
and Electronic Equipment, requires that old household 
electrical appliances must not be disposed of in the 
normal unsorted municipal waste stream. Old applian-
ces must be collected separately in order to optimise 
the recovery and recycling of the materials they contain 
and reduce the impact on human health and the envi-
ronment. The crossed out “wheeled bin” symbol on the 
product reminds you of your obligation, that when you 
dispose of the appliance it must be separately collected. 
  Consumers should contact their local authority or retailer 
for information concerning the correct disposal of their 
old appliance.
  
						

							10
GB
Care and maintenance 
Cutting off the water and electricity 
supplies
•	 Turn	off	the	water	tap	after	every	wash	cycle.	This	will	
limit wear on the hydraulic system inside the washing 
machine and help to prevent leaks.
•	 Unplug	the	washing	machine	when	cleaning	it	and	du-
ring all maintenance work.
Cleaning the washing machine
The outer parts and rubber components of the appliance 
can be cleaned using a soft cloth soaked in lukewarm 
soapy water. Do not use solvents or abrasives.
Cleaning the detergent dispenser drawer
Remove the dispenser by 
raising it and pulling it out 
(see figure).
Wash it under running wa-
ter; this operation should be 
repeated frequently.
Caring for the door and drum of your 
appliance
•	 Always	leave	the	porthole	door	ajar	in	order	to	prevent	
unpleasant odours from forming.
Cleaning the pump
The washing machine is fitted with a self-cleaning pump 
which does not require any maintenance. Sometimes, 
small items (such as coins or buttons) may fall into the pre-
chamber which protects the pump, situated in its bottom 
part.
 
!  Make sure the wash cycle has finished and unplug the 
appliance.
To access the pre-chamber:
1. using a screwdriver, 
remove the cover panel 
on the lower front part of 
the washing machine (see 
figure);
2. unscrew the lid by rota-
ting it anti-clockwise (see 
figure): a little water may 
trickle out. This is perfectly 
normal;
3. clean the inside thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks are securely 
in place before you push it onto the appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If there are any 
cracks, it should be replaced immediately: during the wash 
cycles, water pressure is very strong and a cracked hose 
could easily split open.
! Never use second-hand hoses.