KitchenAid Refrigerator Kfcs22evms 7 Manual

							11
TROUBLESHOOTING
First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions)
to possibly avoid the cost of a service call.
In the U.S.A., www.kitchenaid.com     In Canada, www.kitchenaid.ca
Refrigerator Operation
The refrigerator will not operate
■Power cord unplugged? Plug into a grounded 3 prong outlet.
■Is outlet working? Plug in a lamp to see if the outlet is 
working.
■Household fuse blown or circuit breaker tripped? Replace 
the fuse or reset the circuit breaker. If the problem continues, 
call an electrician. 
■Are controls on? Make sure the refrigerator controls are on. 
See “Using the Control(s).”
■New installation? Allow 24 hours following installation for the 
refrigerator to cool completely. 
NOTE: Adjusting the temperature controls to coldest setting 
will not cool either compartment more quickly.
The motor seems to run too much
Your new refrigerator may run longer than your old one due to its 
high-efficiency compressor and fans. The unit may run even 
longer if the room is warm, a large food load is added, doors are 
opened often, or if the doors have been left open.
The refrigerator seems noisy
Refrigerator noise has been reduced over the years. Due to this 
reduction, you may hear intermittent noises from your new 
refrigerator that you did not notice from your old model. Below are 
listed some normal sounds with explanations.
■Buzzing - heard when the water valve opens to fill the ice 
maker
■Pulsating - fans/compressor adjusting to optimize 
performance
■Hissing/Rattling - flow of refrigerant, movement of water 
lines, or from items placed on top of the refrigerator
■Sizzling/Gurgling - water dripping on the heater during 
defrost cycle
■Popping - contraction/expansion of inside walls, especially 
during initial cool-down
■Water running - may be heard when ice melts during the 
defrost cycle and water runs into the drain pan
■Creaking/Cracking - occurs as ice is being ejected from the 
ice maker mold.
The doors will not close completely
■Door blocked open? Move food packages away from door. 
■Bin or shelf in the way? Push bin or shelf back in the correct 
position. 
The doors are difficult to open
■Gaskets dirty or sticky? Clean gaskets and contact surfaces 
with mild soap and warm water. Rinse and dry with soft cloth.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death, 
fire, or electrical shock.
WARNING
WARNING
Explosion Hazard
Use nonflammable cleaner.
Failure to do so can result in death, explosion, or fire. 
						

							12
Temperature and Moisture
Temperature is too warm
■New installation? Allow 24 hours following installation for the 
refrigerator to cool completely.
■Door(s) opened often or left open? Allows warm air to enter 
refrigerator. Minimize door openings and keep doors fully 
closed. 
■Large load of food added? Allow several hours for 
refrigerator to return to normal temperature. 
■Controls set correctly for the surrounding conditions? 
Adjust the controls a setting colder. Check temperature in 
24 hours. See “Using the Control(s).”
There is interior moisture buildup
NOTE: Some moisture buildup is normal.
■Humid room? Contributes to moisture buildup.
■Door(s) opened often or left open? Allows humid air to enter 
refrigerator. Minimize door openings and keep doors fully 
closed. 
Ice and Water
The ice maker is not producing ice or not enough ice
■Refrigerator connected to a water supply and the supply 
shutoff valve turned on? Connect refrigerator to water 
supply and turn water shutoff valve fully open. 
■Kink in the water source line? A kink in the line can reduce 
water flow. Straighten the water source line. 
■Ice maker turned on? Make sure wire shutoff arm or switch 
(depending on model) is in the ON position. 
■New installation? Wait 24 hours after ice maker installation 
for ice production to begin. Wait 72 hours for full ice 
production.
■Freezer door closed completely? Firmly close the freezer 
compartment door. If the freezer compartment door will not 
close all the way, see “The doors will not close completely,” 
earlier in this section. 
■Large amount of ice recently removed? Allow 24 hours for 
ice maker to produce more ice. 
■Ice cube jammed in the ice maker ejector arm?
Remove ice from the ejector arm with a plastic utensil.
■Water filter installed on the refrigerator? Remove filter and 
operate ice maker. If ice volume improves, then the filter may 
be clogged or incorrectly installed. Replace filter or reinstall it 
correctly. 
■Reverse osmosis water filtration system connected to 
your cold water supply? This can decrease water pressure. 
See “Water Supply Requirements.” 
The ice cubes are hollow or small
NOTE: This is an indication of low water pressure.
■Water shutoff valve not fully open? Turn the water shutoff 
valve fully open.
■Kink in the water source line? A kink in the line can reduce 
water flow. Straighten the water source line. 
■Water filter installed on the refrigerator? Remove filter and 
operate ice maker. If ice quality improves, then the filter may 
be clogged or incorrectly installed. Replace filter or reinstall it 
correctly. 
■Reverse osmosis water filtration system connected to 
your cold water supply? This can decrease water pressure. 
See “Water Supply Requirements.”
■Questions remain regarding water pressure? Call a 
licensed, qualified plumber.
Off-taste, odor or gray color in the ice
■New plumbing connections? New plumbing connections 
can cause discolored or off-flavored ice. 
■Ice stored too long? Discard ice. Wash ice bin. Allow 
24 hours for ice maker to make new ice. 
■Odor transfer from food? Use airtight, moisture proof 
packaging to store food. 
■Are there minerals (such as sulfur) in the water? A water 
filter may need to be installed to remove the minerals. 
■Water filter installed on the refrigerator? Gray or dark 
discoloration in ice indicates that the water filtration system 
needs additional flushing. Flush the water system before using 
a new water filter. Replace water filter when indicated. See 
“Water Filtration System.”
The water dispenser will not operate properly 
■Refrigerator connected to a water supply and the supply 
shutoff valve turned on? Connect refrigerator to water 
supply and turn water shutoff valve fully open.
■Kink in the water source line? Straighten the water source 
line. 
■New installation? Flush and fill the water system. See “Water 
Dispenser.”
■Is the water pressure at least 35 psi (241 kPa)? The water 
pressure to the home determines the flow from the dispenser. 
See “Water Supply Requirements.”
■Water filter installed on the refrigerator? Remove filter and 
operate dispenser. If water flow increases, the filter may be 
clogged or incorrectly installed. Replace filter or reinstall it 
correctly.
■Refrigerator door closed completely? Close the door firmly. 
If it does not close completely, see “The doors will not close 
completely,” earlier in this section. 
■Recently removed the doors? Make sure the water 
dispenser wire/tube assembly has been properly reconnected. 
See “Refrigerator Door(s) and Drawer.”
■Reverse osmosis water filtration system connected to 
your cold water supply? This can decrease water pressure. 
See “Water Supply Requirements.”  
						

							13
Water is leaking from the dispenser system
NOTE: One or two drops of water after dispensing is normal.
■Glass not being held under the dispenser long enough? 
Hold the glass under the dispenser 2 to 3 seconds after 
releasing the dispenser lever.
■New installation? Flush the water system. See “Water 
Dispenser.”
■Recently changed water filter? Flush the water system. See 
“Water Dispenser.”
■Water on the floor near the base grille? Make sure the water 
dispenser tube connections are fully tightened. See 
“Refrigerator Door(s) and Drawer.” 
Water from the dispenser is warm
NOTE: Water from the dispenser is only chilled to 50°F (10°C).
■New installation? Allow 24 hours after installation for the 
water supply to cool completely.
■Recently dispensed large amount of water? Allow 24 hours 
for water supply to cool completely.
■Water not been recently dispensed? The first glass of water 
may not be cool. Discard the first glass of water.
■Refrigerator connected to a cold water pipe? Make sure 
the refrigerator is connected to a cold water pipe. See “Water 
Supply Requirements.” 
WATER FILTER CERTIFICATIONS 
						

							14
PRODUCT DATA SHEETS
Interior Water Filtration System
Model UKF8001AXX-750 Capacity 750 Gallons (2839 Liters)
This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The 
concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the 
permissible limit for water leaving the system, as specified in NSF/ANSI 
Standards 42 and 53.  
Test Parameters: pH = 7.5 ± 0.5 unless otherwise noted. Flow = 0.78 gpm (1.9 Lpm). Pressure = 60 psig (413.7 kPa). Temp. = 68°F ± 5°F 
(20°C ± 3°C).
■It is essential that operational, maintenance, and filter 
replacement requirements be carried out for the product to 
perform as advertised.
■The disposable water filter should be replaced at least every 
6months.
■The filter monitor system measures the amount of water that 
passes through the filter and alerts you to replace the filter. 
When 90% of the filter’s rated life is used, the yellow (Order) 
light comes on. When 100% of the filter’s rated life is used, the 
red (Replace) light comes on, and it is recommended that you 
replace the filter. For models without filter status lights, 
replace the filter every 6 months. Use replacement filter 
model UKF8001AXX-750. 2009 suggested retail price of 
$44.99 U.S.A./$49.95 Canada. Prices are subject to change 
without notice. 
■The product is for cold water use only.
■Do not use with water that is microbiologically unsafe or of 
unknown quality without adequate disinfection before or after 
the system. Systems certified for cyst reduction may be used 
on disinfected waters that may contain filterable cysts.
■Refer to the “Water Filtration System” section for the 
Manufacturer’s name and telephone number.
■Refer to the “Warranty” section for the Manufacturer’s limited 
warranty. 
Application Guidelines/Water Supply Parameters
System tested and certified by NSF International against NSF/ANSI Standard 42 for the 
reduction of Chlorine Taste and Odor, Particulate Class I*; and against NSF/ANSI 
Standard 53 for the reduction of Lead, Mercury, Atrazine, Benzene, p-Dichlorobenzene, 
Carbofuran, Toxaphene, Cysts, Turbidity, Asbestos, Tetrachloroethylene and Lindane.
Substance Reduction
Aesthetic EffectsNSF Reduction 
RequirementsAverage
InfluentInfluent Challenge 
ConcentrationMaximum
EffluentAverage
EffluentMinimum%
ReductionAverage% 
Reduction
Chlorine Taste/Odor
Particulate Class I
*50% reduction
85% reduction2.00 mg/L
14,000,000 #/mL2.0 mg/L ± 10%
At least 10,000 
particles/mL0.06 mg/L
370,000 #/mL**0.050625 mg/L
196,666 #/mL97.00%
97.40%97.52%
99.00%
Contaminant
ReductionNSF Reduction 
RequirementsAverage
InfluentInfluent Challenge 
ConcentrationMaximum
EffluentAverage
EffluentMinimum%
ReductionAverage% 
Reduction
Lead: @ pH 6.5
Lead: @ pH 8.50.010 mg/L
0.010 mg/L0.150 mg/L
†
0.150 mg/L†0.15 mg/L ± 10%
0.15 mg/L ± 10%< 0.001 mg/L
< 0.001 mg/L< 0.001 mg/L
< 0.001 mg/L>99.30%
>99.30%>99.30%
>99.30%
Mercury: @ pH 6.5
Mercury: @ pH 8.50.002 mg/L
0.002 mg/L0.006 mg/L
0.0059 mg/L0.006 mg/L ± 10%
0.006 mg/L ± 10%0.0005 mg/L
0.0018 mg/L0.0003 mg/L
0.00073 mg/L91.70%
69.20%95.00%
88.10%
Benzene 0.005 mg/L 0.0133 mg/L 0.015 mg/L ± 10% 0.0005 mg/L 0.0005 mg/L 96.10% 96.30%
p-Dichlorobenzene 0.075 mg/L 0.210 mg/L 0.225 mg/L ± 10% < 0.0005 mg/L < 0.0005 mg/L >99.80% >99.80%
Carbofuran 0.040 mg/L 0.0753 mg/L 0.08 mg/L ± 10% 0.027 mg/L 0.008 mg/L 64.60% 73.45%
Toxaphene 0.003 mg/L 0.015 mg/L 0.015 ± 10% < 0.001 mg/L < 0.001 mg/L >93.3% >93.3%
Atrazine 0.003 mg/L 0.0102 mg/L 0.009 mg/L ± 10% 0.0027 mg/L 0.00105 mg/L 76.30% 89.40%
Asbestos >99% 126.5 MF/L 10
7 to 108 fibers/L††< 0.17 MF/L < 0.17 MF/L >99.99% >99.99%
Live Cysts‡
Turbidity>99.95%
0.5 NTU122,500 #/L
10.5 NTU50,000/L min. 
11 ± 1 NTU< 1 #/L
‡
0.30 NTU< 1 #/L
‡
0.125 NTU>99.99%
97.30%>99.99%
98.80%
Lindane 0.0002 mg/L 0.0019 mg/L 0.002 ± 10% < 0.00016 mg/L 0.000035 mg/L 91.80% 97.90%
Tetrachloroethylene 0.005 mg/L 0.015 mg/L 0.015 mg/L ± 10% < 0.0005 mg/L < 0.0005 mg/L >96.6% >96.6%
Water Supply
Water Pressure
Water Temperature
Service Flow RateCity or Well
35 - 120 psi (241 - 827 kPa)
33
° - 100°F (1° - 38°C)0.78 gpm (2.9 L/min.) @ 60 psi
*
**
†
††
‡
Class I particle size: >0.5 to 
						

							15
Interior Water Filtration System
Model UKF8001AXX-200 Capacity 200 Gallons (757 Liters)
This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The 
concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the 
permissible limit for water leaving the system, as specified in NSF/ANSI 
Standards 42 and 53.  
Test Parameters: pH = 7.5 ± 0.5 unless otherwise noted. Flow = 0.78 gpm (1.9 Lpm). Pressure = 60 psig (413.7 kPa). Temp. = 68°F ± 5°F 
(20°C ± 3°C).
■It is essential that operational, maintenance, and filter 
replacement requirements be carried out for the product to 
perform as advertised.
■The disposable water filter should be replaced at least every 
6months.
■The filter monitor system measures the amount of water that 
passes through the filter and alerts you to replace the filter. 
When 90% of the filter’s rated life is used, the yellow (Order) 
light comes on. When 100% of the filter’s rated life is used, the 
red (Replace) light comes on, and it is recommended that you 
replace the filter. For models without filter status lights, 
replace the filter every 6 months. Use replacement filter 
model UKF8001AXX-200. 2009 suggested retail price of 
$44.99 U.S.A./$49.95 Canada. Prices are subject to change 
without notice. 
■The product is for cold water use only.
■Do not use with water that is microbiologically unsafe or of 
unknown quality without adequate disinfection before or after 
the system. Systems certified for cyst reduction may be used 
on disinfected waters that may contain filterable cysts.
■Refer to the “Water Filtration System” section for the 
Manufacturer’s name and telephone number.
■Refer to the “Warranty” section for the Manufacturer’s limited 
warranty. 
Application Guidelines/Water Supply Parameters
System tested and certified by NSF International against NSF/ANSI Standard 42 for the reduction of 
Chlorine Taste and Odor, Particulate Class I*; and against NSF/ANSI Standard 53 for the reduction of 
Lead, Mercury, Atrazine, Benzene, p-Dichlorobenzene, Carbofuran, Toxaphene, Cysts, Turbidity, 
Asbestos, O-Dichlorobenzene, Ethylbenzene, Chlorobenzene, Endrin, Tetrachloroethylene and Lindane.
Substance Reduction
Aesthetic EffectsNSF Reduction 
RequirementsAverage
InfluentInfluent Challenge 
ConcentrationMaximum
EffluentAverage
EffluentMinimum%
ReductionAverage% 
Reduction
Chlorine Taste/Odor
Particulate Class I
*50% reduction
85% reduction2.00 mg/L
14,000,000 #/mL2.0 mg/L ± 10%
At least 10,000 
particles/mL0.06 mg/L
370,000 #/mL**0.050625 mg/L
196,666 #/mL97.00%
97.40%97.52%
99.00%
Contaminant
ReductionNSF Reduction 
RequirementsAverage
InfluentInfluent Challenge 
ConcentrationMaximum
EffluentAverage
EffluentMinimum%
ReductionAverage% 
Reduction
Lead: @ pH 6.5
Lead: @ pH 8.50.010 mg/L
0.010 mg/L0.150 mg/L
†
0.150 mg/L†0.15 mg/L ± 10%
0.15 mg/L ± 10%< 0.001 mg/L
< 0.001 mg/L< 0.001 mg/L
< 0.001 mg/L>99.30%
>99.30%>99.30%
>99.30%
Mercury: @ pH 6.5
Mercury: @ pH 8.50.002 mg/L
0.002 mg/L0.006 mg/L
0.0059 mg/L0.006 mg/L ± 10%
0.006 mg/L ± 10%0.0005 mg/L
0.0018 mg/L0.0003 mg/L
0.00073 mg/L91.70%
69.20%95.00%
88.10%
Benzene 0.005 mg/L 0.0133 mg/L 0.015 mg/L ± 10% 0.0005 mg/L 0.0005 mg/L 96.10% 96.30%
p-Dichlorobenzene 0.075 mg/L 0.210 mg/L 0.225 mg/L ± 10% < 0.0005 mg/L < 0.0005 mg/L >99.80% >99.80%
Carbofuran 0.040 mg/L 0.0753 mg/L 0.08 mg/L ± 10% 0.027 mg/L 0.008 mg/L 64.60% 73.45%
Toxaphene 0.003 mg/L 0.015 mg/L 0.015 ± 10% < 0.001 mg/L < 0.001 mg/L >93.3% >93.3%
Atrazine 0.003 mg/L 0.0102 mg/L 0.009 mg/L ± 10% 0.0027 mg/L 0.00105 mg/L 76.30% 89.40%
Asbestos >99% 126.5 MF/L 10
7 to 108 fibers/L††< 0.17 MF/L < 0.17 MF/L >99.99% >99.99%
Live Cysts‡
Turbidity>99.95%
0.5 NTU122,500 #/L
10.5 NTU50,000/L min. 
11 ± 1 NTU< 1 #/L
‡
0.30 NTU< 1 #/L
‡
0.125 NTU>99.99%
97.30%>99.99%
98.80%
Lindane 0.0002 mg/L 0.0019 mg/L 0.002 ± 10% < 0.00016 mg/L 0.000035 mg/L 91.80% 97.90%
Tetrachloroethylene 0.005 mg/L 0.015 mg/L 0.015 mg/L ± 10% < 0.0005 mg/L < 0.0005 mg/L >96.6% >96.6%
O-Dichlorobenzene 0.6 mg/L 1.7 mg/L 1.8 mg/L ± 10% < 0.5 mg/L < 0.5 mg/L >99.9% >99.9%
Ethylbenzene 0.7 mg/L 2.2 mg/L 2.1 mg/L ± 10% 0.0048 mg/L 0.11 mg/L 99.80% 99.90%
Chlorobenzene 0.1 mg/L 2.0 mg/L 2.0 mg/L ± 10% 0.0038 mg/L 0.0008 mg/L 99.80% 99.90%
Endrin 0.002 mg/L 0.007 mg/L 0.006 mg/L ± 10% 0.0004 mg/L 0.0002 mg/L 94.30% 96.80%
Water Supply
Water Pressure
Water Temperature
Service Flow RateCity or Well
35 - 120 psi (241 - 827 kPa)
33
° - 100°F (1° - 38°C)0.78 gpm (2.9 L/min.) @ 60 psi
*
**
†
††
‡
Class I particle size: >0.5 to 
						

							16
KITCHENAID® REFRIGERATOR WARRANTY
LIMITED WARRANTYFor one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or 
furnished with the product, KitchenAid brand of Whirlpool Corporation or Whirlpool Canada LP (hereafter “KitchenAid”) will pay for factory 
specified parts and repair labor to correct defects in materials or workmanship that existed when this major appliance was purchased. 
Service must be provided by a KitchenAid designated service company. YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED 
WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. This limited warranty is valid only in the United States or Canada and 
applies only when the major appliance is used in the country in which it was purchased. Proof of original purchase date is required to obtain 
service under this limited warranty.
On models with a water filter: 30 day limited warranty on water filter. For 30 days from the date of purchase, when this filter is operated and 
maintained according to instructions attached to or furnished with the product, KitchenAid will pay for a replacement water filter to correct 
defects in materials and workmanship.
SECOND THROUGH FIFTH YEAR LIMITED WARRANTY ON CAVITY LINER AND SEALED REFRIGERATION SYSTEMIn the second through fifth year from the date of purchase, when this major appliance is operated and maintained according to instructions 
attached to or furnished with the product, KitchenAid will pay for replacement or repair of the refrigerator/freezer cavity liner (including labor 
costs) if the part cracks due to defective materials or workmanship that existed when this major appliances was purchased. Also, in the 
second through fifth year from the date of purchase, when this major appliance is operated and maintained according to instructions 
attached to or furnished with the product, KitchenAid will pay for factory specified parts and repair labor for the following components to 
correct defects in materials or workmanship in the sealed refrigeration system that existed when this major appliance was purchased: 
compressor, evaporator, condenser, dryer, and connecting tubing.
SIXTH THROUGH TENTH YEAR LIMITED WARRANTY ON SEALED REFRIGERATION SYSTEMIn the sixth through tenth year from the date of purchase, when this major appliance is operated and maintained according to instructions 
attached to or furnished with the product, KitchenAid will pay for factory specified parts for the following components to correct defects in 
materials or workmanship in the sealed refrigeration system that existed when this major appliance was purchased: compressor, evaporator, 
condenser, dryer, and connecting tubing.
ITEMS EXCLUDED FROM WARRANTYThis limited warranty does not cover:
1.Replacement parts or repair labor if this major appliance is used for other than normal, single-family household use or when it is used in 
a manner that is inconsistent to published user or operator instructions and/or installation instructions.
2.Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or repair 
house fuses, or to correct house wiring or plumbing.
3.Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty 
coverage.
4.Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in accordance 
with electrical or plumbing codes, or use of products not approved by KitchenAid.
5.Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage results 
from defects in materials or workmanship and is reported to KitchenAid within 30 days from the date of purchase.
6.Any food or medicine loss due to refrigerator or freezer product failures.
7.Pickup and delivery. This major appliance is intended to be repaired in your home.
8.Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
9.Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an 
authorized KitchenAid servicer is not available.
10.The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance with 
KitchenAids published installation instructions.
11.Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered or cannot 
be easily determined.
DISCLAIMER OF IMPLIED WARRANTIESIMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A 
PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do not 
allow limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This warranty gives 
you specific legal rights, and you also may have other rights that vary from state to state or province to province.
LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGESYOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. 
KITCHENAID SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the 
exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives 
you specific legal rights, and you also may have other rights that vary from state to state or province to province.
If outside the 50 United States and Canada, contact your authorized KitchenAid dealer to determine if another warranty applies.6/08 
						

							17
For additional product information, in the U.S.A., visit www.kitchenaid.com 
In Canada, visit www.kitchenaid.ca 
If you do not have access to the Internet and you need assistance using your product or you would like to schedule service, you may 
contact KitchenAid at the number below.
Have your complete model number ready. You can find your model number and serial number on the label, located on the inside wall of 
the refrigerator compartment.
For assistance or service in the U.S.A., call 1-800-422-1230. In Canada, call 1-800-807-6777.
If you need further assistance, you can write to KitchenAid with any questions or concerns at the address below:
In the U.S.A.:
KitchenAid Brand Home Appliances
Customer eXperience Center
553 Benson Road
Benton Harbor, MI 49022-2692In Canada:
KitchenAid Brand Home Appliances
Customer eXperience Centre
200 – 6750 Century Ave.
Mississauga, Ontario  L5N 0B7
Please include a daytime phone number in your correspondence.
Please keep these User Instructions and the model number information for future reference. 
						

							18 LE AGRADECEMOS la compra de este producto de alta calidad. Si usted experimenta un problema que no se haya cubierto en 
SOLUCIÓN DE PROBLEMAS, visite nuestro sitio de internet en www.kitchenaid.com para obtener información adicional. Si 
considera que aún necesita ayuda, llámenos al 1-800-422-1230. En Canadá, visite nuestro sitio de internet en 
www.kitchenaid.ca o llámenos al 1-800-807-6777. 
Necesitará tener a mano su número de modelo y de serie ubicados
 en la pared interior del compartimiento del refrigerador.
SEGURIDAD DEL REFRIGERADOR
INSTRUCCIONES PARA 
EL USUARIO DEL REFRIGERADOR
Si no sigue las instrucciones de inmediato, usted puede 
morir o sufrir una lesión grave.   
Si no sigue las instrucciones, usted puede morir o sufrir 
una lesión grave.
Todos los mensajes de seguridad le dirán el peligro potencial, le dirán cómo reducir las posibilidades de sufrir una lesión y lo que 
puede suceder si no se siguen las instrucciones.
Su seguridad y la seguridad de los demás es muy importante.
Hemos incluido muchos mensajes importantes de seguridad en este manual y en su electrodoméstico. Lea y obedezca siempre 
todos los mensajes de seguridad.
ADVERTENCIA
PELIGRO
Este es el símbolo de advertencia de seguridad.
Este símbolo le llama la atención sobre peligros potenciales que pueden ocasionar la muerte o una lesión a 
usted y a los demás.
Todos los mensajes de seguridad irán a continuación del símbolo de advertencia de seguridad y de la palabra 
“PELIGRO” o “ADVERTENCIA”. Estas palabras significan:
Para reducir el riesgo de incendio, choque eléctrico, o lesiones personales al usar su refrigerador siga  
estas precauciones básicas:ADVERTENCIA: INSTRUCCIONES IMPORTANTES DE SEGURIDAD
CONSERVAR ESTAS INSTRUCCIONES
■ Conecte a un contacto de pared de conexión a tierra de 
3 terminales.
■ No use un adaptador.
■ No quite la terminal de conexión a tierra.
■ No use un cable eléctrico de extensión.
■ Desconecte el suministro de energía antes de darle servicio. 
■ Vuelva a colocar todos los componentes y paneles antes de 
hacerlo funcionar.
■ Remueva las puertas de su refrigerador viejo.
■ Use un limpiador no inflamable.
■ Mantenga los materiales y vapores inflamables, tales como 
gasolina, alejados del refrigerador.
■ Use dos o más personas para mover e instalar el 
refrigerador.
■ Desconecte el suministro de energía antes de instalar la 
fábrica de hielo (en aquellos modelos que incluyen el juego 
de instalación de la fábrica de hielo).
■ Use un vaso resistente para recibir hielo del despachador 
(en algunos modelos).
■ No golpee las puertas de vidrio del refrigerador (en algunos 
modelos). 
						

							19
Cómo deshacerse adecuadamente de 
su refrigerador viejo
IMPORTANTE: El atrapamiento y asfixia de niños no es un 
problema del pasado. Los refrigeradores tirados y abandonados 
son un peligro, aun si van a quedar ahí “por unos pocos días”. Si 
Ud. está por deshacerse de su refrigerador viejo, por favor siga 
las instrucciones que se dan a continuación para prevenir 
accidentes.
Antes de tirar su viejo refrigerador o congelador:
■Saque las puertas.
■Deje los estantes en su lugar, así los niños no pueden meterse 
adentro con facilidad.
INSTRUCCIONES DE INSTALACIÓN
Desempaque el refrigerador
Cómo quitar los materiales de empaque
■Quite los restos de cinta y goma de las superficies de su 
refrigerador antes de encenderlo. Frote un poco de 
detergente líquido para vajillas sobre el adhesivo con los 
dedos. Limpie con agua tibia y seque.
■No use instrumentos filosos, alcohol para fricciones, líquidos 
inflamables o productos de limpieza abrasivos para eliminar 
los restos de cinta o goma. Estos productos pueden dañar la 
superficie de su refrigerador. Para más información, vea 
“Seguridad del refrigerador”.
■Deshágase de todos los materiales de embalaje o recíclelos. 
Limpieza antes del uso
Una vez que usted haya quitado todos los materiales de 
empaque, limpie el interior de su refrigerador antes de usarlo. Vea 
las instrucciones de limpieza en “Cuidado de su refrigerador”.
Requisitos de ubicación
Para asegurar la adecuada ventilación para su refrigerador, deje 
un espacio de ¹⁄₂ (1,25 cm) a cada lado y por encima. Deje un 
espacio de 1 (2,54 cm) detrás del refrigerador. Si su refrigerador 
tiene fábrica de hielo, asegúrese que hay espacio adicional atrás 
para las conexiones de la línea de agua. Si Ud. instala el 
refrigerador próximo a una pared fija, deje 2¹⁄₂ (6,3 cm) mínimo 
del lado de la bisagra (algunos modelos requieren más), para 
permitir que la puerta se abra completamente.
ADVERTENCIA
Peligro de Asfixia
Remueva las puertas de su refrigerador viejo.
No seguir esta instrucción puede ocasionar la muerte 
o daño al cerebro.
ADVERTENCIA
Peligro de Peso Excesivo
Use dos o más personas para mover e instalar 
el refrigerador.
No seguir esta instrucción puede ocasionar una 
lesión en la espalda u otro tipo de lesiones.
Cómo mover su refrigerador:
Su refrigerador es pesado. Cuando mueva el refrigerador 
para limpiarlo o para darle servicio, cerciórese de cubrir 
el piso con cartón o madera para evitar daños en el mismo. 
Al mover el refrigerador, siempre tire directamente hacia 
afuera. No menee el refrigerador de lado a lado ni lo haga 
“caminar” cuando lo trate de mover ya que podría dañar 
el piso.
Información importante para saber acerca de los estantes 
y tapas de vidrio:
No limpie los estantes y tapas de vidrio con agua caliente 
mientras están fríos. Los estantes y tapas pueden romperse 
si se exponen a cambios bruscos de temperatura o impacto, 
como sería un golpe brusco. El vidrio templado se ha 
diseñado para hacerse añicos. Esto es normal. Los estantes 
y tapas de vidrio son muy pesados. Use ambas manos al 
sacarlos para evitar que se caigan.
ADVERTENCIA
Peligro de Explosión
Mantenga los materiales y vapores inflamables, 
tales como gasolina, alejados del refrigerador.
No seguir esta instrucción puede ocasionar la muerte, 
explosión, o incendio. 
						

							20
NOTA: No se recomienda instalar el refrigerador cerca de un 
horno, radiador u otra fuente de calor. No instale el refrigerador en 
un lugar donde la temperatura sea menor de 55°F (13°C).
Requisitos eléctricos
Antes de mover el refrigerador a su posición definitiva, es 
importante asegurarse que Ud. tiene la conexión eléctrica 
adecuada.
Método de conexión a tierra recomendado
Se requiere una fuente de energía eléctrica de 115 Voltios, 
60 Hz., CA solamente y con fusibles de 15 ó 20 amperios, 
debidamente conectada a tierra. Se recomienda que se use un 
circuito separado sólo para su refrigerador. Use un tomacorriente 
que no se puede apagar con un interruptor. No use un cable 
eléctrico de extensión.
NOTA: Antes de realizar cualquier tipo de instalación, limpieza o 
de quitar un foco de luz, APAGUE el enfriamiento (Cooling OFF), y 
luego desconecte el refrigerador de la fuente de energía. Cuando 
Ud. haya terminado, reconecte el refrigerador a la fuente de 
energía eléctrica y ENCIENDA el enfriamiento (Cooling ON). Vea 
“Uso de los controles”.
Requisitos del suministro de agua
Reúna las herramientas y piezas necesarias antes de comenzar la 
instalación. Lea y siga las instrucciones provistas con cualquiera 
de las herramientas enlistadas aquí.
HERRAMIENTAS NECESARIAS: 
IMPORTANTE:
■Todas las instalaciones deben hacerse de acuerdo a los 
requisitos locales de plomería.
■No use una válvula perforadora o una válvula de montura de 
³⁄₁₆ (4,76 mm), la cual reduce el flujo de agua y se obstruye 
con más facilidad.
■Use tubería de cobre y revise si hay fugas. Instale la tubería de 
cobre sólo en áreas donde la temperatura vaya a permanecer 
por encima del punto de congelación.
■Para modelos con filtros de agua, el filtro de agua desechable 
deberá reemplazarse por lo menos cada 6 meses.
Presión del agua
Se necesita un suministro de agua fría con presión de agua entre 
35 y 120 lbs/pulg² (241 y 827 kPa) para hacer funcionar el 
despachador de agua y la fábrica de hielo. Si tiene preguntas 
acerca de la presión del agua, llame a un plomero competente 
autorizado.
Suministro de agua por ósmosis inversa
IMPORTANTE: La presión del suministro de agua que sale de un 
sistema de ósmosis inversa y va a la válvula de entrada de agua 
del refrigerador necesitará ser entre 35 y 120 lbs/pulg² (241 y 
827 kPa).
Si se conecta un sistema de filtración de agua de ósmosis inversa 
al suministro de agua fría, la presión de agua al sistema de 
ósmosis inversa necesitará ser de un mínimo de 40 a 60 lbs/pulg² 
(276 a 414 kPa).
Si la presión de agua hacia el sistema de ósmosis inversa es 
menor de 40 a 60 lbs/pulg² (276 a 414 kPa):
■Verifique si el filtro de sedimentos en el sistema de ósmosis 
inversa está bloqueado. Reemplácelo si fuera necesario.
■Deje que se vuelva a llenar el tanque de almacenaje del 
sistema de ósmosis inversa después del uso intenso.
■Si su refrigerador tiene un filtro de agua, se podrá reducir la 
presión aún más si se usa en conjunto con un sistema de 
ósmosis inversa. Saque el filtro de agua. Vea “Sistema de 
filtración de agua”.
Si tiene preguntas acerca de la presión del agua, llame a un 
plomero competente autorizado.
Conecte el suministro de agua
Lea todas las instrucciones antes de comenzar.
IMPORTANTE: Si usa el refrigerador antes de conectar la tubería 
de agua, ponga la fábrica de hielo en la posición OFF (Apagado).
Conexión a la línea de agua
1.Desenchufe el refrigerador o desconecte el suministro de 
energía.
2.CIERRE el suministro principal de agua. ABRA la llave de agua 
más cercana el tiempo suficiente para que la tubería de agua 
se vacíe.
3.Localice una tubería de agua fría vertical de ¹⁄₂ a 1¹⁄₄ 
(12,7 mm a 31,8 mm) cerca del refrigerador.
2¹⁄₂ (6,3 cm)
¹⁄₂ (1,25 cm)
ADVERTENCIA
Peligro de Choque Eléctrico
Conecte a un contacto de pared de conexión a tierra de 
3 terminales.
No quite la terminal de conexión a tierra.
No use un adaptador.
No use un cable eléctrico de extensión.
No seguir estas instrucciones puede ocasionar 
la muerte, incendio o choque eléctrico.
■Destornillador de hoja plana
■Llaves de boca de ⁷⁄₁₆ y ¹⁄₂ o 
dos llaves ajustables
■Llave de tuercas de ¹⁄₄
■Broca de¹⁄₄
■Taladro inalámbrico