Kodak Professional 6800 User Manual

							Safety and Regulatory Information
B-3
Regulatory and Safety Compliance
SafetyComplies with UL 60950 Third Edition—CAN/CSA C22.2
No. 60950 Third Edition
EN 60950:2000
IEC 60950 Fourth Edition
Radio Frequency 
InterferenceNOTE:  This equipment has been tested and found to comply with the limits 
for a Class A digital device, pursuant to part 15 of the FCC rules. These 
limits are designed to provide reasonable protection against 
interference when the equipment is operated in a commercial 
environment. This equipment generates, uses, and can radiate radio 
frequency energy and, if not installed and used in accordance with 
the instruction manual, may cause interference to radio 
communications. Operation of this equipment in a residential area is 
likely to cause interference in which case the user will be required to 
correct the interference at his or her own expense.
Requirements of the EMC directive 89/336/EEC were met through compliance 
with the following:
 EN 55022: 94 (class B) with Amendments A1:95 and A2:97
 EN 55024: 98 ITE Immunity includes the following:
EN61000-4-2 ESD
EN61000-4-3 Radiated rf immunity
EN61000-4-4 EFT
EN61000-4-5 Surge
EN61000-4-6 Conducted rf immunity
EN61000-4-11 Voltage dips and interruptions
 EN 61000-3-2 Harmonics
 EN 61000--3-3 Flicker
Changes or modifications not expressly approved by the party responsible for 
compliance could void the user’s authority to operate the equipment.
This is a Class A product based on the standard of the Voluntary Control 
Council for Interference from Information Technology Equipment (VCCI). If 
this is used near a radio or television receiver in a domestic environment, it 
may cause radio interference. Install and use the equipment according to the 
instruction manual.
Downloaded From ManualsPrinter.com Manuals 
						

							 B-4 Safety and Regulatory Information
Noise EmissionThe operator-position noise emission value is 58 dB(A).*
* Average value specified in accordance to JIS Z8731
DisposalThis product contains a small amount of lead in the solder on the circuit 
boards. Disposal of this material may be regulated due to environmental 
considerations. For disposal or recycling information, please contact your 
local authorities. In the USA, contact the Electronics Industry Alliance at 
http://www.eiae.org.
Downloaded From ManualsPrinter.com Manuals 
						

							I-1
Index
A
air flow clearances, 1-2
C
cabinet, cleaning, 5-1
cables
connecting, 1-7
power, 1-7
USB, 1-8
calibrating the printer, 3-1
calibration errors, 3-8
calibration software
installing, 3-1
uninstalling, 3-8
calibration utility, 3-1
checking
paper status, 4-2
ribbon status, 4-2
cleaning
cabinet, 5-1
cleaning rollers, 5-3
platen roller, 5-3
stripper plate, 5-2
thermal head, 5-2
cleaning rollers, cleaning, 5-3
clearing paper jam, 6-3
connecting cables, 1-7
contents, package, 1-1
D
disposal, B-4
E
error messages
calibration, 3-8
operator panel, 6-2H
handling
paper, A-3
prints, 4-1
ribbon, A-3
help with your printer, A-4
humidity
paper and ribbon specifications, A-2
printer specifications, A-1
I
installing
calibration software, 3-1
paper, 1-8
print catcher, 1-4
printer driver, 2-1
ribbon, 1-5
trim tray, 1-4
K
KODAK Photo Print Kit, A-2
KODAK Photo Printer Print Catcher, A-3
KODAK Thermal Printer Cleaning Kit, A-3
L
labels, safety, B-2
loading
paper, 1-8
ribbon, 1-5
M
maintenance
cabinet, 5-1
cleaning rollers, 5-3
KODAK Thermal Printer Cleaning Kit, A-3
platen roller, 5-3
stripper plate, 5-2
thermal head, 5-2
Downloaded From ManualsPrinter.com Manuals 
						

							I-2 Index
N
noise emission spec, B-4
O
online user guide, 1-11
operator panel
error messages, 6-2
lights, 4-1
making a test print, 4-2
Paper Advance, loading paper, 1-10
printer settings, 4-2
Ready message, 4-2
setup mode, 4-2
ordering supplies, A-2
output tray
See print catcher, 1-4
P
package contents, 1-1
packing material, removing, 1-3
packing the printer, A-3
paper
handling and storing, A-3
loading, 1-8
reordering, A-2
specifications, A-2
Paper Advance, operator panel, 1-10
paper jam, clearing, 6-3
paper status, checking, 4-2
platen roller, cleaning, 5-3
power
cable, 1-7
interruption, recovering, 6-4
requirements, A-1
turning on, 1-8
print catcher, 1-4
reordering, A-3
printer
calibrating, 3-1
operating, 4-1
preferences, customizing, 2-2
properties, customizing, 2-2
setting up, 1-1
settings, 4-2
specifications, A-1
printer disposal, B-4
printer driver
installing, 2-1
uninstalling, 2-2printer problems, resolving, 6-1
printing
making prints, 4-1
test print, 4-2
prints
handling and storing, 4-1
making, 4-1
problems, 6-1
R
radio frequency compliance, B-3
Ready message, operator panel, 4-2
recycling, B-4
reordering supplies, A-2
ribbon
handling and storing, A-3
loading, 1-5
reordering, A-2
specifications, A-2
ribbon status, checking, 4-2
S
safety
compliance, B-3
tips, B-1
warning labels, B-2
setting up the printer, 1-1
setup mode, 4-2
software
installing
calibration software, 3-1
printer driver, 2-1
uninstalling
calibration software, 3-8
printer driver, 2-2
specifications
paper and ribbon, A-2
printer, A-1
storing
prints, 4-1
ribbon, A-3
stripper plate, cleaning, 5-2
supplies, printer, A-2
support, A-4
switch, power, 1-8
system requirements, A-1
Downloaded From ManualsPrinter.com Manuals 
						

							Index
I-3
T
temperature
paper and ribbon specifications, A-2
printer specifications, A-1
test print, making, 1-10
thermal head, cleaning, 5-2
transporting the printer, A-3
trim tray, 1-4
troubleshooting
clearing paper jam, 6-3
error messages, operator panel, 6-2
potential problems, 6-1
power interruption, 6-4
U
uninstalling
calibration software, 3-8
printer driver, 2-2
unpacking, 1-3
USB cable, connecting, 1-8
Downloaded From ManualsPrinter.com Manuals 
						

							Downloaded From ManualsPrinter.com Manuals