Konica Minolta bizhub 43 User Manual

bizhub 43
- 11 -
2 -  Installation
6Press on the right lateral paper guide and slide it to 
the required paper format.
7Fan the paper and even it up on a flat surface to 
prevent paper jams or skewed prints.
8Load the sheets into the paper tray with the print 
surface facing up.
9Make sure the paper does not exceed the fill limit.
10Replace the cover on the paper tray. Ensure that 
the cover is properly closed.11Replace the paper tray in the machine and push it 
in fully.
12Define the paper format and...

- 12 -
bizhub 43
2 -  Installation
4Press on the longitudinal paper guide and slide it to 
the required paper format.
5Press on the longitudinal paper guide and slide it to 
the required paper format.
6Fan the transparencies in small quantities and 
even them up on a flat surface to prevent paper 
jams or skewed prints.
7Load the transparencies into the paper tray with the 
print surface facing up.
8Make sure the transparencies do not exceed the fill 
limit.9Replace the cover on the paper tray. Ensure...

bizhub 43
- 13 -
2 -  Installation
2Connect one end of the LAN network cable (not 
supplied) to the machine port and the other to your 
local network port for the machine.
3Ensure that the On/Off button is on Off (position 0).
4Connect the mains cable to the machine. Connect 
the mains cable to the wall socket.
5Press the On/Off button to switch the machine on 
(position I).Initial configuration of the machine
In this section, you will find the initial settings to be 
configured to be able to use your...

- 14 -
bizhub 43
2 -  Installation
To run an automatic configuration of the Ethernet 
network (automatic allocation of the IP address via the 
DHCP server):
1In the menu SETTINGS, press COMMUNICATION 
> LOCAL NETWORK > ETHERNET > IPV4 > 
CONFIGURATION.
2Select AUTOMATIC from the options available in 
the list. Press OK to confirm the new setting.
>The machine will search for a DHCP or BOOTP 
server on the local network that can dynamically 
allocate its network settings.
>This operation may take a few...

bizhub 43
- 15 -
3 -  Getting to know the machine
Getting to know 
the machine
Please read this section carefully to get to know your 
machine.
In it you will find the operating principles required 
whatever function you are using.
Navigation principles
Using the buttons
Navigating through the machines functions and menus is 
very intuitive.
The touch screen displays the functions, menus, actions 
and parameters in the form of buttons.
Just press on a button to open a menu and access the 
sub-menus, run...

- 16 -
bizhub 43
3 -  Getting to know the machine
Presentation of the home screen and 
menus
The home screen allows you to access:
• machine configuration utilities and menus
• monitoring of operations and communications in 
progress
• warning and error messages
The machine displays the home screen either:
• by pressing the MENU key
• by pressing the Home icon in the navigation path
• or when a specific function is running, to display the 
current operation progress (document being scanned, 
fax being...

bizhub 43
- 17 -
3 -  Getting to know the machine
Monitoring of operations and 
communications in progress
The operations and communications in progress are 
displayed in the central frame of the home screen in the 
form of buttons.
Sending a fax is thus represented by a button labelled Fax 
emission, receiving a fax by a button labelled Fax 
reception, etc.
To help you identify the operations and communications 
in progress, the possible labels are as follows:
 
To check or consult the operation data,...

- 18 -
bizhub 43
3 -  Getting to know the machine
Inserting original documents
The instructions for inserting original documents are the 
same for copies, faxes or scanned documents.
Using the flatbed scanner
Accepted formats
The format of documents for scanning should respect the 
following conditions:
• Maximum length: 299 mm.
• Maximum width: 219 mm.
Inserting the document
1Open the cover of the flatbed scanner.
2Place your document with the side to be copied 
face down on the window respecting the...

bizhub 43
- 19 -
3 -  Getting to know the machine
 
Logging in on the machine
Depending on the machine configuration, access to 
functions may require logging in with a user code or by 
fingerprint reading. This information is defined in your 
user account by the machine administrator.
For your login information and user rights attributed to 
you, consult your machine administrator.
When a function (e.g.: copy, scan, etc.) or access to a 
function requires authorisation, a login screen is 
displayed.To...

- 20 -
bizhub 43
3 -  Getting to know the machine
Personalising your user account / 
fingerprint
Your user account is created by the machine 
administrator, who will inform you of your 4-figure user 
code.
You can personalise some information:
 
To personalise your user information:
1Press MENU.
2Press [OTHER COMMANDS] > IDENTIFICATION 
> PERSON. DATA.
>The machine displays the identification screen.
3Enter your 4-figure user code using the virtual key-
board or the keypad.
>The consultable /...