Home > Konica > Printer > Konica Minolta bizhub C10P User Manual

Konica Minolta bizhub C10P User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Konica Minolta bizhub C10P User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 61 Konica manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Dual In-Line Memory Module (DIMM) 139
    6Reconnect all interface cables.
    7Reconnect the power cord, and 
    turn on the printer.
    8Declare the additional RAM in the Windows printer driver (Properties/Con-
    figure tab, see Page 10).
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Hard Disk 140
    Hard Disk
    If a hard disk is installed, fonts can be downloaded and saved, and the over-
    lay function can be used.
    Installing a Hard Disk
    Note
    It’s very important to protect the printer controller board and any 
    associated circuit boards from electrostatic damage. Before performing 
    this procedure, review the antistatic caution on 
    Page 136. In addition, 
    always handle circuit boards by the edges only.
    1Turn off the printer and discon-
    nect the power cord and inter-
    face cables.
    If the duplex option is 
    installed, remove it.
    2Using a screwdriver, remove the 
    screw on the back of the printer.
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Hard Disk 141
    3Remove the rear panel.
    Since there are two 
    hooks on the right side of 
    the panel, remove the 
    rear panel by slightly pull
    -
    ing the left side of the 
    panel toward you, then 
    sliding the panel off to the 
    left.
    4Attach the mounting pin on the 
    printer controller board.
    Be sure to slide the tab 
    on the hard disk mount
    -
    ing pin to the left during 
    installation.
    5Attach the spacer to the hard 
    disk controller board.
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Hard Disk 142
    6Attach the hard disk to the 
    printer controller board.
    7Reinstall the panel and tighten the screw.
    If you removed the duplex option in step1, reinstall it.
    8Reconnect all interface cables.
    9Reconnect the power cord, and 
    turn on the printer.
    10Declare the hard disk in the Windows printer driver (Properties/Configure 
    tab, see 
    Page 10).
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Duplex Option 143
    Duplex Option
    Duplex (Double Sided) printing can be performed automatically with the 
    duplex option and enough memory installed. See 
    “Required Memory during 
    Printing” on page 137.
    Installing the Duplex Option
    1Turn off the printer.
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Duplex Option 144
    2Remove the two knockout plates 
    and the tape.
    3Prepare the duplex option.
    Before installing the 
    duplex option, open the 
    duplex cover and check 
    that the knob is posi
    -
    tioned vertically. After 
    checking the knob, close 
    the cover.
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Duplex Option 145
    4Install the duplex option.
    Note
    When attaching the duplex option, attach the bottom of the option first, 
    as shown. If the duplex option is attached incorrectly, it may be 
    damaged.
    5Open the cover of the duplex 
    option.
    Since the duplex option is 
    not yet secured to the 
    printer, hold the duplex 
    option in place when 
    opening its cover.
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Duplex Option 146
    6While pushing in the knobs, turn 
    them clockwise until they are 
    horizontal.
     
    The duplex option is secured in 
    place.
    Make sure that both 
    knobs are securely 
    locked.
    7Close the duplex cover.
    8Declare the duplex in the Win-
    dows printer driver (Properties/Configure tab, see Page 10).
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Tray 2 147
    Tray 2
    If Tray 2 is installed, up to 500 additional sheets of A4/Letter-size paper can 
    be loaded.
    Installing Tray 2
    Note
    Since consumables are installed in the printer, be sure to keep the 
    printer level when moving it in order to prevent accidental spills.
    1Turn off the printer and discon-
    nect the power cord and inter-
    face cables.
    2Prepare Tray 2.
    Be sure to place Tray 2 on a level surface.
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Tray 2 148
    3Lift the printer and place it on top 
    of Tray 2, making sure that the 
    positioning pins on Tray 2 cor
    -
    rectly fit into the holes in the bot-
    tom of the printer.
    4Declare the Tray 2 in the Windows printer driver (Properties/Configure 
    tab, see 
    Page 10).
    Downloaded From ManualsPrinter.com Manuals 
    						
    All Konica manuals Comments (0)

    Related Manuals for Konica Minolta bizhub C10P User Manual