Kyocera FS 1350DN User Manual

							7-14Using the Operation Panel
1 Firmware Version
This item shows the version and release date of the printer firmware.
2 Printer Settings Information
This item shows various printer settings for hardware-related items:
•MP tray paper size and type
•Paper cassette size and type
•Sleep time
•Formfeed timeout time
3 Installed Options
This item shows the option installed in the printer:
•Memory card (CompactFlash card)
4 Network Status
This item shows the IP address, subnet mask address, and default 
gateway address for the network interface card in the printer.
5 Interface Information
This information shows the settings for all interfaces installed in the 
printer.
6Memory
This item shows:
•Standard memory in the printer
•Option memory slot status in kilobytes
•Total memory in the printer 
•Current status of the RAM disk 
7Emulation
This item shows all available emulations of the printer. The PCL 6 
emulation is set as default when the printer is shipped from the 
factory. The emulations are:
•PCL 6
•KPDL
•Line Printer
•IBM Proprinter
•DIABLO 630
•EPSON LQ-850
8 Page Information
This item shows the page related items:
•Total printed page count
•Total page count of each paper size
9 Consumable Status
This item shows the approximate level of remaining toner. When the 
value is 100, the toner container is full. The closer to 0, the smaller 
the amount of remaining toner.
Downloaded From ManualsPrinter.com Manuals 
						

							Using the Operation Panel7-15
Print Fonts List
To help you decide in selecting a font, you can printout lists of the 
internal fonts or the optional fonts.
1Press Z while Report Print > is displayed.
2Press U or V repeatedly until >Print Fonts List appears.
3Press [OK]. A question mark (?) appears.
4Press [OK] again. The message Processing appears and the 
printer prints a list of fonts with a sample and font ID (number) for 
each of them.
Print RAM Disk File List
This allows you to print a list of the files on the RAM disk.
1Press Z while Report Print > is displayed.
2Press U or V repeatedly until >Print RAM Disk File List 
appears.
3Press [OK]. A question mark (?) appears.
4Press [OK] again. The message Processing appears and the 
printer prints a list of files stored in a RAM disk.
Print Mem. Card File List
This allows you to print a list of the files on a CompactFlash (memory) 
card.
1Press Z while Report Print > is displayed.
2Press U or V repeatedly until >Print Mem. Card File List 
appears.
3Press [OK]. A question mark (?) appears.
4Press [OK] again. The message Processing appears and the 
printer prints a list of files stored in a 
CF card.
>Print
 Fonts List ?
IMPORTANTThis is displayed when RAM disk mode is enabled.
>Print RAM Disk
 File List ?
IMPORTANTThis message will be displayed when the 
CompactFlash (CF) card installed in the printer.
>Print Mem. Card
 File List ?
Downloaded From ManualsPrinter.com Manuals 
						

							7-16Using the Operation Panel
USB Memory (USB flash memory selection)
This specifies the settings for removing the USB flash memory and 
printing USB flash memory content. The USB Memory menu 
automatically appears when you install the USB memory.
The options available in USB flash memory are as follows:
•Print File (Printing a file)
• Copies (Number of copies)
• Paper Source (Selecting the paper feed source)
• Remove Device (Removing the USB flash memory)
• Print File List (Printing a list of the files on a USB flash memory)
1Press [MENU] .
2Press  or  repeatedly until  USB Memory > appears. 
Note that menus shown in the list may vary depending on which 
optional units installed in the printer.
Print File (Printing a file)
You can use this to specify printing for files in the USB flash memory.
1Press   while USB Memory > is displayed.
2>Print File appears. In other displays, press   or   repeatedly 
until the map appears.
3Press [OK] . A question mark ( ?) appears. 
4Press [OK]  again. The folder or file appears. 
(For example :  Folder 1)
Each time you press   or , the next folder or file appears in 
succession. 
To view lower-level folders or files, press  . 
(For example :  Folder 2)
To view folders or files on still lower levels, press  . 
(For example :  File 3)
You can move between the folder levels by pressing   and   or  
and  .
5Press [OK] . A question mark ( ?) appears.
(For example :  File 3)
6Press [OK]  again. Copies  appears.
IMPORTANTThis message is displayed  only when the USB host 
block is set to 
Unblock. For more information, refer to Interface Block 
(Interface (external device) block setting)  on page7-57.
USB Memory     >
IMPORTANT The Print File menu option is only displayed 
when there is a PDF, TIFFor XPS  file in the USB flash memory. 
Note also that up to 3 levels of folders or files are displayed. It 
might take some time before the  folder or file name appears, 
depending on the size of the USB flash memory or the number of 
files.
/
  /00:Folder 1
/00:Folder 1
  /01:Folder 2
/.../01:Folder 2
    02:File 3
/.../01:Folder 2
?   02:File 3
Copies
             001
Downloaded From ManualsPrinter.com Manuals 
						

							Using the Operation Panel7-17
Copies (Number of copies)
Sets the number of copies printed of the specified file in USB flash 
memory.
While Copies  in step 5 above is displayed, press   and   or   and   
to display the number of copies. (E.g.:  10)
7Press [OK]. Paper Source  and a question mark ( ?) appears.
Paper Source (Selecting the paper feed source)
Sets the paper used for printing the specified file in USB flash memory.
1While  Paper Source  in step 2 above is displayed, press   and   
or   and   repeatedly until the paper source appears. 
(For example :  Cassette 2)
Note that menus shown in the list may vary depending on which 
optional units installed in the printer.
2Press [OK] . The message  Processing appears and the printer 
prints a file stored in a USB flash memory.
Remove Device (Removing the USB flash memory)
Specifies the setting for USB flash memory removal.
1Press   while USB Memory >  is displayed.
2Press  or  repeatedly until  >Remove Device appears.
3Press [OK]. A question mark ( ?) appears.
4Press [OK]  again. Menu display ends and the USB flash memory 
device can be removed.
Print File List (Printing a  list of the files on a USB 
flash memory)
This allows you to print a list of the files on a USB flash memory device.
1Press   while USB Memory >  is displayed.
2Press  or  repeatedly until  >Print File List  appears.
3Press [OK]. A question mark ( ?) appears.
4Press [OK]  again. The message  Processing appears and the 
printer prints a list of files stored in a USB flash memory.
IMPORTANT To use this feature, the RAM disk must be set to On.
Copies
             010
Paper Source
? Cassette 1
Paper Source
? Cassette 2
>Remove Device ?
 
>Print
 File List ?
Downloaded From ManualsPrinter.com Manuals 
						

							7-18Using the Operation Panel
Counter (Viewing the counter value)
This only displays the total number of pages printed. You cannot change 
the displayed number.
1Press [MENU].
2Press U or V repeatedly until Counter > appears.
3Press Z. >Printed Pages appears as he total number of pages 
printed. (E.g.: 2000)
4Press [MENU]. The display returns to Ready.
Counter        >
>Printed Pages
           0002000
Downloaded From ManualsPrinter.com Manuals 
						

							Using the Operation Panel7-19
Paper Settings
This sets the paper size and type for the MP tray and cassettes from 
which paper is supplied.
The options available in Paper Settings are as follows:
•MP Tray Size (Setting MP tray paper size)
•MP Tray Type (Setting the MP tray paper type)
•Cassette (1 to 3) Size (Setting the cassette paper size)
•Cassette (1 to 3) Type (Setting the cassette paper type)
•Type Adjust (Creating custom paper type)
•Reset Type Adjust (Resetting the custom paper type)
1Press [MENU].
2Press U or V repeatedly until Paper Settings > appears.Paper Settings >
Downloaded From ManualsPrinter.com Manuals 
						

							7-20Using the Operation Panel
MP Tray Size (Setting MP tray paper size)
When you use the MP tray, you should set the MP tray size to the paper 
size that is used to format the job to print. If the sizes do not match, 
printing will not be performed on the correct size paper. 
The default setting is Letter size for the U.S. and Canada and A4 for 
other countries. For more information about the paper sizes that you can 
feed from the MP tray, refer to Paper Specifications on page2-2.
1Press Z while Paper Settings > is displayed.
2Press U or V repeatedly until >MP Tray Size appears.
3Press [OK]. A blinking question mark (?) appears.
4Press U or V to display the desired paper size. The message 
display toggles through the following paper sizes:
Env. Monarch
Envelope #10
Envelope #9
Envelope #6
Envelope DL
Envelope C5
A6
B6
A5
B5
ISO B5
A4
Executive
Letter
Legal
Custom
Oficio II
Statement
Folio
Youkei 2
Youkei 4
16K
Hagaki
OufukuHagaki
5Press [OK].
6Press [MENU]. The display returns to Ready.
MP Tray Type (Setting the MP tray paper type)
You can use this to set the paper type that can be supplied from the MP 
tray. The default setting is PLAIN.
For more information about paper types that you can feed from the MP 
tray, refer to Paper Specifications on page2-2.
1Press Z while Paper Settings > is displayed.
2Press U or V repeatedly until >MP Tray Type appears.
NoteFeeding the paper having a paper size which does not 
match the current paper size from the MP tray can cause paper 
jam.
>MP Tray Size
? A4
Downloaded From ManualsPrinter.com Manuals 
						

							Using the Operation Panel7-21
3Press [OK]. A blinking question mark (?) appears.
4Press U or V to display the desired paper type. The message 
display toggles through the following paper types:
PLAIN
TRANSPARENCY
PREPRINTED
LABELS
BOND
RECYCLED
VELLUM
ROUGH
LETTERHEAD
COLOR
PREPUNCHED
ENVELOPE
CARDSTOCK
THICK
HIGH QUALITY
CUSTOM 1 (to 8)
5Press [OK].
6Press [MENU]. The display returns to Ready.
Cassette (1 to 3) Size (Setting the cassette paper size)
To set the size for the paper cassette, load the paper into a paper 
cassette, adjust the paper size, and select the paper size from the 
operation panel.
If the PF-100 optional paper feeder is installed, use the same procedure 
to load paper into the paper feeder cassettes.
1Pull the cassette out of the printer.
2Adjust the position of the width guides located on the left and right 
sides of the cassette. Press the release button on the left guide and 
slide the guides to the paper size required, and load the paper into 
the cassette.
Proceed to the next section to select the paper size from the operation 
panel.
NoteYou can define any paper type and store that definition 
in the printer. For more information, refer to Type Adjust 
(Creating custom paper type) on page7-25.
>MP Tray Type
? PLAIN
Downloaded From ManualsPrinter.com Manuals 
						

							7-22Using the Operation Panel
Setting the Paper Size from the Operation Panel
Use the operation panel to set the size of paper loaded in the cassette 
on the printer.
1Press Z while Paper Settings > is displayed.
2Press U or V repeatedly until >Cassette Size > appears. If 
optional paper feeders are added, Cassette1 Size will appear for 
the standard paper cassette and Cassette2 Size, and 
Cassette3 Size will appear for the optional paper feeders.
3Press [OK]. A blinking question mark (?) appears.
4Press U or V to display the desired paper size. The message 
display toggles through the following paper sizes:
Envelope C5
A6
A5
B5
ISO B5
A4
Executive
Letter
Legal
Custom
Oficio II
Statement
Folio
16K
5When the desired paper size is displayed, press [OK]. The paper 
size is set for the paper cassette.
If you selected Custom in step 4, be sure to set the unit of 
measurement and the dimensions of the paper as described in the 
following sections.
Select the units of measurement as described in the next section.
NoteA6 and Statement will not appear if Cassette 2 to 
3 of optional paper feeder PF-100 is selected.
>Cassette Size >
? Custom
Downloaded From ManualsPrinter.com Manuals 
						

							Using the Operation Panel7-23
Unit (Selecting the unit of measurement)
1Press Z.
2Press U or V repeatedly until >>Unit appears. The unit of 
measurement can be selected between millimeters and inches. The 
current unit of measurement is displayed (the default setting is mm).
3Press [OK]. A blinking question mark (?) appears.
4Select mm or inch using U or V. 
5Press [OK]. 
Set the dimensions of the paper as described in the next section.
Entering the Width and Length
Enter the paper size for X Dimension and Y Dimension as shown in 
the figure. 
1When the unit of measurement is set, press V. 
>>X Dimension appears (the paper width setting).
2Press [OK]. A blinking cursor (_) appears.
3Press U or V to increase or decrease the value of the figure where 
the cursor is blinking and display the desired width. 
Acceptable paper widths are as follows:
•Cassette: 105 to 216 mm (4.13 to 8.5 inches)
•Paper Feeder PF-100 (optional): 148 to 216 mm (5.83 to 8.5 
inches)
4Display the paper width and press [OK].
5When the width is set, press V. >>Y Dimension appears (the 
paper length setting). Set the desired length in the same way as the 
width. 
Acceptable paper lengths are as follows:
•Cassette: 148 to 356 mm (5.83 to 14.02 inches)
•Paper Feeder PF-100 (optional): 210 to 356 mm (8.5 to 14.02 
inches)
6Display the paper length, press [OK].
7Press [MENU]. The display returns to Ready. 
>>Unit
? mm
X Dimension
Y Dimension
105 to 216mm 
(4-1/8 to 8-1/2 inches)148 to 356mm 
(5-13/16 to 14 inches)
>>X Dimension
           216
 mm
Downloaded From ManualsPrinter.com Manuals