Kyocera FS 1350DN User Manual

							x
Compliance and Conformity
FCC Statement (for users in the United States and Canada)
This device complies with Part 15 of FCC Rules and RSS-Gen of IC 
Rules. Operation is subject to the following two conditions; (1) this 
device may not cause harmful interference, and (2) this device must 
accept any interference received, including interference that may cause 
undesired operation of the device.
This equipment has been tested and found to comply with the limits for a 
Class B digital device, pursuant to part 15 of the FCC Rules. These limits 
are designed to provide reasonable protection against harmful 
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy 
and, if not installed and used in accordance with the instructions, may 
cause harmful interference to radio communications. However, there is 
no guarantee that interference will not occur in a particular installation. If 
this equipment does cause harmful interference to radio or television 
reception, which can be determined by turning the equipment off and on, 
the user is encouraged to try to correct the interference by one or more 
of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and the receiver.
•Connect the equipment into an outlet on a circuit different from that 
to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party 
responsible for compliance could void the users authority to operate the 
equipment.
Properly shielded grounded cables and connectors must be used for 
connection to host computer and/or peripherals in order to meet FCC 
emission limits.
Precautions for Use
Any modifications without prior permission of Kyocera may cause 
harmful interference.
If any modifications or changes are made to this equipment without prior 
permission of Kyocera, Kyocera as the manufacturer does not guarantee 
the compliance with the FCC Rules. The use of equipment that does not 
comply with the FCC Rules is prohibited.
Downloaded From ManualsPrinter.com Manuals 
						

							xi
Safety Infor mation
Laser Safety
This printer is certified as a Class 1 laser product under the U.S. 
Department of Health and Human Services (DHHS) Radiation 
Performance Standard according to Radiation Control for Health and 
Safety Act of 1968. This means that the printer does not produce 
hazardous laser radiation. Since radiation emitted inside the printer is 
completely confined within protective housings and external covers, the 
laser beam cannot escape from the printer during any phase of user 
operation.
Laser Notice
This printer is certified in the U.S. to conform to the requirements of 
DHHS 21 CFR Subchapter for Class I (1) laser products, and elsewhere 
is certified as a Class I laser product conforming to the requirements of 
IEC 825.
Radio Frequency Transmitter
This machine contains a transmitter module. We, the manufacturer 
(Kyocera Mita Corporation) hereby declare that this equipment (page 
printer), model FS-1350DN is in compliance with the essential 
requirements and other relevant provisions of Directive 1999/5/EC.
Radio Tag Technology
In some countries, the radio tag technology used in this equipment to 
identify the toner container may be subject to authorization, and the use 
of this equipment may consequently be restricted.
DANGER CLASS 3B INVISIBLE LASER RADIATION 
WHEN OPEN. AVOID DIRECT EXPOSURE TO BEAM.
CAUTION  Use of controls or adjustments or performance 
of procedures other than those specified herein may result 
in hazardous radiation exposure.
Downloaded From ManualsPrinter.com Manuals 
						

							xii
Caution Labels
The printer bears any of the following labels.
CDRH Regulations
The Center for Devices and Radiological Health (CDRH) of the U.S. 
Food and Drug Administration implemented regulations for laser 
products on August 2, 1976. These regulations apply to laser products 
manufactured after August 1, 1976. Compliance is mandatory for 
products marketed in the United States. A label indicating compliance 
with the CDRH regulations must be attached to laser products marketed 
in the United States.
Ozone Concentration
These printers generate ozone gas (O3), which may concentrate in the 
place of installation and cause an unpleasant smell. To minimize the 
concentration of ozone gas to less than 0.1ppm, we recommend you not 
to install the printer in a confined area where ventilation is blocked.
Laser inside the printer
(Laser radiation warning) Laser inside the printer
(Laser radiation warning)
For Europe, Asia, and 
other countriesFor U.S.A. and 
Canada
Downloaded From ManualsPrinter.com Manuals 
						

							xiii
Declaration of Conformity for U.S.A.
Model name: Page Printer FS-1350DN
Trade name: Kyocera Mita
Responsible party: Kyocera Mita America, Inc.
Address: 225 Sand Road PO Box 40008 Fairfield, New Jersey 07004-
0008, U.S.A.
Telephone: (973) 808-8444
Fax: (973) 882-6000
Manufacturer: Kyocera Mita Corporation (Head Office)
Manufacturer’s address: 2-28, 1-Chome, Tamatsukuri, Chuo-ku, Osaka 
540-8585, Japan
This device complies with Part 15 of the FCC Rules. Operation is subject 
to the following two conditions: (1) this device may not cause harmful 
interference, and (2) this device must accept any interference received, 
including interference that may cause undesired operation.
The manufacturer and its merchandising companies retain the following 
technical documentation in anticipation of the inspection that may be 
conducted by the authorities concerned:
User’s instruction that conforms to the applicable specifications.
Technical drawings.
Descriptions of the procedures that guarantee the conformity.
Other technical information.
Kyocera Mita America Inc.
CE Marking Directive
Hereby, Kyocera Mita Corporation, declares that this page printer is in 
compliance with the essential requirements and other relevant 
provisions of Directive 1999/5/EC.
According to Council Directive 89/336/EEC, 2006/95/EC, and 1999/5/EC
Manufacturer: Kyocera Mita Corporation (Head Office)
Manufacturer’s address: 2-28, 1-Chome, Tamatsukuri, Chuo-ku, Osaka 
540-8585, Japan
Declares that the product
Product name: Page Printer
Model number: FS-1350DN (as tested with enhancement optional unit; 
Paper Feeder PF-100)
Conforms to the following product specifications:
EN 55 022:1998+A1:2000+A2:2003 Class B
EN 61 000-3-2:2000
EN 61 000-3-3:1995+A1:2001
EN 55 024:1998+A1:2001+A2:2003
EN 60 950-1:2001+A11
EN 60 825-1:1994+A1+A2
EN 300330-1
EN 300330-2
Downloaded From ManualsPrinter.com Manuals 
						

							xiv
The manufacturer and its merchandising companies retain the following 
technical documentation in anticipation of the inspection that may be 
conducted by the authorities concerned:
Users instruction that conforms to the applicable specifications.
Technical drawings.
Descriptions of procedures that guarantee conformity.
Other technical information.
Declaration of Conformity (Australia)
Manufacturer: Kyocera Mita Corporation (Head Office)
Manufacturer’s address: 2-28, 1-Chome, Tamatsukuri, Chuo-ku, Osaka 
540-8585, Japan
declares that the product
Product name: Page Printer
Model name: FS-1350DN
Description of devices: This Page Printer Model FS-1350DN is 30ppm; 
A4 size and utilizes plain paper; dry toner; etc. The printer can be 
equipped with several optional enhancement units, such as a PF-100 
paper feeder.
conforms to the following product specifications:
AS/NZS 3548: 1995 (EN 55 022: 1998 Class B)
AS/NZS 4268: 2003
IEC60950-1:2001 (EN 60 950-1: 2001+A11)
The manufacturer and its merchandising companies retain the following 
technical documentation in anticipation of the inspection that may be 
conducted by the authorities concerned:
User’s instruction that conforms to the applicable specifications
Technical drawings
Descriptions of procedures that guarantee conformity
Other technical information
The manufacturer has been employed with ISO9001 scheme. JQA and 
BS have attested the manufacturer.
Kyocera Mita Australia Pty., Ltd.
6-10 Talavera Road, North Ryde, NSW 2113, Australia
Telephone: +61 2-9888-9999
Fax: +61 2-9888-9588
Canadian Department of Communications 
Compliance Statement
This Class B digital apparatus complies with Canadian ICES-003.
Avis de conformité aux normes du ministere 
des Communications du Canada
Cet appareil numérique de la classe B est conforme à la norme NMB-
003 du Canada.
Downloaded From ManualsPrinter.com Manuals 
						

							xv
EN ISO 7779
Maschinenlärminformations-Verordnung 3. GPSGV, 06.01.2004: Der 
höchste Schalldruckpegel beträgt 70 dB (A) oder weniger gemäß EN 
ISO 7779.
Disclaimer
Kyocera Mita will not be liable to customers or any other person or entity 
for any loss or damage caused or alleged to be caused directly or 
indirectly by equipment sold or furnished by us, including but not limited 
to, any interruption of service, loss of business or anticipatory profits, or 
consequential damages resulting from the use or operation of the 
equipment or software.
Energy Saving Function
This printer comes equipped with a Sleep Mode where printer function 
remains in a waiting state but power consumption is still reduced to a 
minimum when there is no activity with the printer within a set amount of 
time.
Sleep Mode
This printer automatically enters Sleep Mode when approximately 15 
minutes have passed since the printer was last used. The amount of 
time of no activity that must pass before Sleep Mode is activated may be 
lengthened.
Duplex Printing
This printer includes duplex printing as a standard function. For example, by 
printing two single-sided originals onto a single sheet of paper as a duplex 
printing, it is possible to lower the amount of paper used. 
Recycled Paper
This printer supports recycled paper which reduces the load on the 
environment. Your sales or service representative can provide 
information about recommended paper types.
Energy Star (ENERGY STA R®) Program 
We have determined as a participating company in the International 
Energy Star Program that this product is compliant with the standards 
laid out in the International Energy Star Program.
Downloaded From ManualsPrinter.com Manuals 
						

							xvi
Symbols
The sections of this guide and parts of the machine marked with symbols 
are safety warnings meant to protect the user, other individuals and 
surrounding objects, and ensure correct and safe usage of the machine. 
The symbols and their meanings are indicated below.
The following symbols indicate that the related section includes safety 
warnings. Specific points of attention are indicated inside the symbol.
The following symbols indicate that the related section includes 
information on prohibited actions. Specifics of the prohibited action are 
indicated inside the symbol. 
The following symbols indicate that the related section includes 
information on actions which must be performed. Specifics of the 
required action are indicated inside the symbol.
Please contact your service representative to order a replacement if the 
safety warnings in this Operation Guide are illegible or if the guide itself 
is missing. (fee required)DANGER: Indicates that serious injury or even death will very 
possibly result from insufficient attention to or incorrect 
compliance with the related points.
WA R N I N G: Indicates that serious injury or even death may 
result from insufficient attention to or incorrect compliance with 
the related points.
CAUTION: Indicates that personal injury or mechanical 
damage may result from insufficient attention to or incorrect 
compliance with the related points.
.... [General warning]
.... [Warning of danger of electrical shock]
.... [Warning of high temperature]
.... [Warning of prohibited action]
.... [Disassembly prohibited]
.... [Alert of required action]
.... [Remove the power plug from the outlet]
....[Always connect the machine to an outlet with a ground 
connection]
Downloaded From ManualsPrinter.com Manuals 
						

							xvii
Installation Precautions
Environment
Caution
Avoid placing the machine on or in locations which are unstable 
or not level. Such locations may cause the machine to fall down 
or fall over. This type of situation presents a danger of personal 
injury or damage to the machine.
Avoid locations with humidity or dust and dirt. If dust or dirt 
become attached to the power plug, clean the plug to avoid the 
danger of fire or electrical shock.
Avoid locations near radiators, heaters, or other heat sources, or 
locations near flammable items, to avoid the danger of fire.
To keep the machine cool and facilitate changing of parts and 
maintenance, allow access space as shown below. Leave 
adequate space, especially around the rear cover, to allow air to 
be properly ventilated out of the printer.
Other Precautions
Adverse environmental conditions may affect the safe operation and 
performance of the machine. Install in an air-conditioned room 
(recommended room temperature: around 23°C (73.4°F), humidity: 
around 60 % RH), and avoid the following locations when selecting a site 
for the machine.
•Avoid locations near a window or with exposure to direct sunlight.
•Avoid locations with vibrations. 
•Avoid locations with drastic temperature fluctuations. 
•Avoid locations with direct exposure to hot or cold air.
•Avoid poorly ventilated locations.
During printing, some ozone is released, but the amount does not cause 
any ill effect to ones health. If, however, the printer is used over a long 
period of time in a poorly ventilated room or when printing an extremely 
large number of copies, the smell may become unpleasant. To maintain 
the appropriate environment for print work, it is suggested that the room 
be properly ventilated.
11-13/16
(300mm)7-7/8
(200mm) 11-13/16
(300mm)19-11/16
(500mm) 7-7/8
(200mm)
Downloaded From ManualsPrinter.com Manuals 
						

							xviii
Power Supply/Grounding the Machine
Warning
Do not use a power supply with a voltage other than that 
specified. Avoid multiple connections in the same outlet. These 
types of situations present a danger of fire or electrical shock.
Plug the power cord securely into the outlet. If metallic objects 
come in contact with the prongs on the plug, it may cause a fire or 
electric shock.
Always connect the machine to an outlet with a ground 
connection to avoid the danger of fire or electrical shock in case 
of an electric short. If an earth connection is not possible, contact 
your service representative.
Other precautions
Connect the power plug to the closest outlet possible to the machine.
The power supply cord is used as the main disconnect device. Ensure 
that the socket/outlet is located/installed near the equipment and is 
easily accessible.
Handling of plastic bags
Warning
Keep the plastic bags that are used with the machine away from 
children. The plastic may cling to their nose and mouth causing 
suffocation.
Downloaded From ManualsPrinter.com Manuals 
						

							xix
Precautions for Use
Cautions when using the machine
Warning
Do not place metallic objects or containers with water (flower 
vases, flower pots, cups, etc.) on or near the machine. This 
situation presents a danger of fire or electrical shock should they 
fall inside. 
Do not remove any of the covers from the machine as there is a 
danger of electrical shock from high voltage parts inside the 
machine.
Do not damage, break or attempt to repair the power cord. Do not 
place heavy objects on the cord, pull it, bend it unnecessarily or 
cause any other type of damage. These types of situations 
present a danger of fire or electrical shock.
Never attempt to repair or disassemble the machine or its parts as 
there is a danger of fire, electrical shock or damage to the laser. If 
the laser beam escapes, there is a danger of it causing blindness.
If the machine becomes excessively hot, smoke appears from the 
machine, there is an odd smell, or any other abnormal situation 
occurs, there is a danger of fire or electrical shock. Turn the main 
power switch off ({) immediately, be absolutely certain to remove the 
power plug from the outlet and then contact your service representative.
If anything harmful (paper clips, water, other fluids, etc.) falls into 
the machine, turn the main power switch off ({) immediately. 
Next, be absolutely certain to remove the power plug from the 
outlet to avoid the danger of fire or electrical shock. Then contact your 
service representative.
Do not remove or connect the power plug with wet hands, as 
there is a danger of electrical shock.
Always contact your service representative for maintenance or 
repair of internal parts.
Caution
Do not pull the power cord when removing it from the outlet. If the 
power cord is pulled, the wires may become broken and there is a 
danger of fire or electrical shock. (Always grasp the power plug 
when removing the power cord from the outlet.)
Always remove the power plug from the outlet when moving the 
machine. If the power cord is damaged, there is a danger of fire or 
electrical shock.
If the machine will not be used for a short period of time 
(overnight, etc.), turn the power switch off (O). If it will not be used 
for an extended period of time (vacations, etc.), remove the power 
plug from the outlet for safety purposes during the time the machine is 
not in use.
Always hold the designated parts only when lifting or moving the 
machine.
For safety purposes, always remove the power plug from the 
outlet when performing cleaning operations.
Downloaded From ManualsPrinter.com Manuals