Lexmark C920n User Manual

Installing a hard disk
31
Installing and removing options
If an option card has been installed, you may have to remove the option card before installing the hard disk.
1Remove the system board access cover (see Removing the system board access cover).
2Align and press the ribbon cable connector into the connector on the system board.
3Flip the hard disk over, and then press the three posts on the mounting plate into the holes on the system board. 
The hard disk snaps into place.
Downloaded From...

Installing an option card
32
Installing and removing options
Installing an option card
Your printer has one expansion card slot that supports a number of option cards. The following table describes their 
function.
Note:The network models ship with an Ethernet print server already installed.
You need a small Phillips screwdriver to install these options.
1Remove the system board access cover (see Removing the system board access cover).
2Remove the screw from the metal plate that covers the connector...

Installing an option card
33
Installing and removing options
4Align the connector on the option card with the connector on the system board.
The cable connectors on the side of the option card must fit through the connector slot.
5Push the option card firmly into the option card connector.
6Secure the card to the system board with the screws.
Downloaded From ManualsPrinter.com Manuals 

Reinstalling the system board access cover
34
Installing and removing options
Reinstalling the system board access cover
After you finish installing cards on the printer system board, reinstall the system board access cover.
1Align the holes on the access cover with the screws on the printer. 
2Place the cover against the printer and slide it down.
3Tighten the eight screws.
Aligning the optional high capacity feeder
Note:Failure to properly align the high capacity feeder may cause paper jams.
Hole...

Aligning the optional high capacity feeder
35
Installing and removing options
Installing height adjustment spacers
If the pins on the high capacity feeder do not align with the holes in the docking frame, adjust the height of the feeder.
You can either remove the factory installed spacer or add two spacers between each caster and the bottom of the high 
capacity feeder.
Use the following steps to add or remove spacers.
1Determine the height difference between high capacity feeder alignment pins and the...

Aligning the optional finisher
36
Installing and removing options
cAlign and insert the screws into the screw holes on the high capacity feeder.
To remove the factory installed spacer:
aRemove the spacer from the top of the caster.
bInsert the four screws through the caster.
cAlign and insert the screws into the screw holes on the high capacity feeder.
5Tighten the four screws to secure the caster.
6Repeat steps 3 through 5 to add or remove spacers on the remaining three casters.
Note:If installing or...

Aligning the optional finisher
37
Installing and removing options
Aligning the finisher with the printer
The following three areas must align properly to prevent paper jams.
1The docking plate pins must enter the holes in the finisher.
2The space between the printer and finisher must be the same at the top and bottom of the finisher.
3The alignment marks on top of the finisher must align with the edges of the cover on the side of the printer.
4Roll the finisher toward the printer until the finisher locks...

Aligning the optional finisher
38
Installing and removing options
Lowering or raising the finisher
Follow these instructions if the holes on the finisher are above or below the pins on the docking plate.
1Determine if the pins are above or below the holes in the finisher.
Hole in finisher
Pin
Downloaded From ManualsPrinter.com Manuals 

Aligning the optional finisher
39
Installing and removing options
2Loosen the guide rail thumbscrews.
3Rotate the adjustment knobs as needed to align the holes in the finisher with the pins.
To raise the finisher, rotate the adjustment knobs clockwise.
To lower the finisher, rotate the adjustment knobs counterclockwise.
4Roll the finisher toward the printer until the finisher locks to the docking plate pins.
You hear a click when the finisher locks into position.
If the pins go into the holes but the...

Aligning the optional finisher
40
Installing and removing options
Aligning the sides of the finisher
Follow these instructions if the distance between the finisher and printer is not the same at the top and bottom.
1Loosen the guide rail thumbscrews.
Downloaded From ManualsPrinter.com Manuals