Maytag Mhw6000x W Manual

11
   whites
hea
vy dut y
delicate
r ins e/dr ain  
         & spin small
   lo
ad
 with  clean
wa sher
bed ding
wr
ink le co ntrol
 allergen
nor
mal
soa k
8. Select CYCLE
The display will show the default settings for the selected   
cycle. If desired, press the button beneath each setting to  
adjust the Temp Level, Soil Level, and Spin Speed. Adjusting 
the Soil Level will change the Estimated Time Remaining.  
Overloading, unbalanced loads, or excessive suds may also 
cause the washer to increase the...

12
Cycle Status Lights
The Cycle Status Lights show the progress of a cycle. At each 
stage of the process, you may notice sounds or pauses that are 
different from traditional washers.
Door Locked
 Door Locked will light to indicate that the door is locked and 
cannot be opened without first pausing or canceling the cycle. 
Sensing
  When the START/PAUSE button is pressed, the washer will 
first perform a self-test on the door lock mechanism. You will 
hear a click, the drum will make a partial turn,...

13
WASHER MAINTENANCE
CLEANING YOUR WASHER
Keep your washer as clean and fresh as your clothes.  
To keep washer interior odor-free, follow this recommended 
cleaning procedure at least once a month:
1. Make sure laundry drum is empty.
2.  Using recommended AFFRESH
® washer cleaner, add 
one tablet to washer basket.
  OR
  If using liquid chlorine bleach, add 1 cup (250 mL) to 
liquid chlorine bleach dispenser.
IMPORTANT: Do not add detergent to Clean Washer 
with Affresh
® cycle. Do not use more than...

14
CLEANING THE DOOR SEAL
1. Open the washer door and remove any clothing or items 
from the washer.
2.  Inspect the gray colored seal between the door opening 
and the basket for stained areas. Pull back the seal to 
inspect all areas under the seal and to check for foreign 
objects.
CLEANING THE DISPENSER
You may find laundry product residue leftover in your 
dispenser compartments. To remove residue, follow this  
recommended cleaning procedure:
1. Pull dispenser drawer out until it stops.
2.  Press...

15
Operate your washer only when you are home. If moving, 
or not using your washer for a period of time, follow these 
steps:
1. Unplug or disconnect power to washer.
2.  Turn off water supply to washer to avoid flooding due  
to water pressure surges.
WINTER STORAGE CARE
IMPORTANT: To avoid damage, install and store washer 
where it will not freeze. Because some water may stay in 
hoses, freezing can damage washer. If storing or moving 
during freezing weather, winterize your washer.
To winterize...

16
If you experiencePossible Causes Solution
First try the solutions suggested here or visit our website at www.maytag.com/help  
for assistance and to possibly avoid a service call.  
Error Code Appears in Display
Sud (Excess suds)  
appears in display Excessive suds in washer. Washer is 
running a suds reduction routine.  Allow the machine to continue. Use only HE detergent.  
Always measure detergent, and base detergent quantity on  
load size. Follow detergent manufacturer’s instructions. 
Press...

17
First try the solutions suggested here or visit our website at www.maytag.com/help  for assistance and to possibly avoid a service call.  
If you experience Possible Causes Solution
Feet may not be in contact with the 
floor and locked.Front and rear feet must be in firm contact with floor, and washer 
must be level to operate properly. Jam nuts must be tight 
against the bottom of the cabinet.
Check floor for flexing or sagging. If flooring is uneven, a 3/4" \
(19 mm) piece of plywood under your...

18
Normal washer operation.Door must be completely closed and latched for washer to run.
Washer will pause during certain phases of cycle.  
Do not interrupt cycle.
The washer pauses for about 2 minutes during certain cycles. 
Allow the cycle to continue. Some cycles feature periods of 
tumbling and soak.
Washer may be stopped to reduce suds. Plug power cord into a grounded 3 prong outlet.
Do not use an extension cord.
Ensure there is power to outlet.  
Check electrical source or call an electrician to...

19
Washer not performing as expected (cont.)
If you experiencePossible causes
Solution
Incorrect or wrong 
wash or rinse  
temperaturesCheck for proper water supply.
Make sure hot and cold inlet hoses are not reversed.
Both hoses must be attached to both washer and faucet, and 
have both hot and cold water flowing to inlet valve.
Check that inlet valve screens are not clogged.
Remove any kinks in hoses.
First try the solutions suggested here or visit our website at www.maytag.com/help  
for assistance...

20
Load not rinsedCheck for proper water supply.Make sure hot and cold inlet hoses are not reversed.
Both hoses must be attached and have water flowing to the 
inlet valve.
Both hot and cold water faucets must be on.
Inlet valve screens on washer may be clogged.
Remove any kinks in the inlet hose.
Not using HE detergent or using too 
much HE detergent. The suds from regular detergent can cause the washer  
to operate incorrectly.
Use only HE detergent. Always measure detergent and follow 
manufacturer’s...