Motorola 800 Hgv B Manual

							
Gateway User Interface
29
Configuring Advanced Firewall Settings
The Edit Advanced Firewall Settings page allows you to configure advanced features on your firewall. 
Enabling Advanced Security
The 2Wire gateway firewall already provides a high level of security. You can configure the firewall to provide 
advanced security features, including stealth mode, strict UDP , or block pings.
 Stealth Mode. When in stealth mode, the 2Wire  gateway firewall does not return information in 
response to network queries; that is, it will appear to  hackers who are tr ying to access your network 
that your network does not exist. This discourages  hackers from further attempts at accessing your 
network, because to them it will appear as thoug h there is no active network to access.
 Block Ping. Ping is a basic Internet program that,  when used without malicious intent, allows a user to 
verify that a particular IP address exists and can a ccept requests. Hackers can use ping to launch an 
attack against your network, because ping can det ermine the number form of the network’s IP address 
(for example, 105.246.172.72) from the domain nam e (for example, www.mynetwork.com). If you 
enable Block Ping, your network will block all ping requests.  
						

							
Gateway User Interface
30
 Strict UDP Session Control. Enabling this feature provides increased security by preventing the 2Wire 
gateway from accepting packets sent from  an unknown source over an existing connection.  The ability 
to send traffic based on destination only is required  by some applications. Enabling this feature may not 
allow some on-line applications to work properly.
Allowing Inbound and Outbound Traffic
The Inbound and Outbound Control pane displays some  common protocol types. When one of the Inbound 
protocol boxes is checked, the firewall allows the co rresponding protocol to pass through from the Internet 
to the network. If one of the Outbound protocol boxes  is checked, the firewall allows the traffic from the 
network to pass through the firewall to the Internet.
Note: If you configure the firewall to block an Inbound protocol, you may disable suppor t for 
hosted applications that require that type of protocol.
Disabling Attack Detection
By default, the 2Wire gateway firewall rules block the a ttack types listed in the Attack Detection pane. There 
are some applications and devices that require the us e of specific data por ts through the firewall. The 
gateway allows users to open the necessary por ts thr ough the firewall using the Firewall Settings page. If 
the user requires that a computer have all incoming tra ffic available to it, this computer can be set to the 
DMZplus mode. While in DMZplus mode, the com puter is still protected against numerous broadband 
attacks (for example, SYN Flood or  Invalid TCP flag attacks).
I n rare cases, the incoming traffic may be inadvertently blocked by the firewall (for example, when 
integrating with external third-par ty firewalls or VP N ser vers). You may need to disable one or more of the 
attack detection capabilities for any device placed in  the DMZplus. In this case, the third-par ty server 
provides the attack protection normally provided by the gateway.
Following are the attacks for which the gateway firewall filters continuously checks.
 Excessive Session Detection. When enabled, the fire wall will detect applications on the local network 
that are creating excessive sessions out to the Internet . This activity is likely due to a virus or “worm” 
infected computer (for example, Blaster Worm). When  the event is detected, the gateway displays a 
HURL warning page.
 TCP/UDP Por t Scan. A por t scan is a series of mess ages sent by someone attempting to break into a 
computer to learn which computer network ser vic es, each associated with a well-known port number 
(such as UDP and TCP), the computer provides . When enabled, the firewall detects UDP and TCP port 
scans, and drops the packet.
 Invalid Source/Destination IP address. When enabled,  the firewall will verify IP addresses by checking 
for the following:
− IP source address is broadcast  or multicast — drop packet.
− TCP destination IP address is not unicast — drop packet.
− IP source and destination address are the same — drop packet.
− Invalid IP source received from private/home network — drop packet. 
						

							
Gateway User Interface
31
 Packet Flood (SYN/UDP/ICMP/Other). When enabled, the firewall will check for SYN, UDP, ICMP, and 
other types of packet floods on the local and Internet facing interfaces and stop the flood.
 Invalid TCP Flag Attacks  (NULL/XMAS/Other). When enabled, the firewall will scan inbound and 
outbound packets for invalid TCP Flag settings, and  drop the packet to prevent SYN/FIN, NULL, and 
XMAS attacks.
 Invalid ICMP Detection. The firewall checks for invalid ICMP/code types, and drops the packet.
 Miscellaneous. The firewall checks for the following:
−Unknown IP protocol — drop packet.
− Por t 0 attack detected — drop packet.
− TCP SYN packet — drop packet.
− Not a start session packet — drop packet.
− ICMP destination unreachable — terminate session. 
						

							
32
Access the Management and Diagnostic 
Console
Accessing the Management and Diagnostic Console
The Management and Diagnostic Console (MDC) provides information about the status of the 2Wire 
gateway, its broadband network connections, attached  home networking devices, system and security 
information, and a running log of any error conditions.
To access the MDC locally, in the browser address bar enter 
http://gateway.2wire.net/management
.
After you access the MDC, use the left-hand navigation menu to select specific MDC pages.
System Summary Page
The System Summar y page shows general information about the 2Wire gateway, its configuration, 
and components. 
						

							
Access the Management and Diagnostic Console
33
Depending on the ser vice provider and the components installed, the System Summar y page may include 
the following information:
Item Description
System
Model 2Wire gateway model number (for example, 3700HGV-B).
Serial number 2Wire gateway serial number.
MAC Address 2Wire gateway MAC address.
Hardware Version 2Wire gateway hardware version.
Hardware Options The type of peripheral device installed.
DSL Modem Type VDSL.
Current Software 2Wire gateway software version.
Configuration
Key Code The static key code associated with the current  provisioning settings.
System Time The day, month, year, and time; or “Retrieving date and  time settings from Internet” if not set.
Time Since Last Boot The time elapsed since the 2Wire gateway was last  restar ted.
Last ID Post The time elapsed since the 2Wire gateway communicated  with the configuration ser ver.
Components
DSL Modem Modem software version.
common_en The language in which the user interface is presented  (common_en = English).
Firewall Rules Current version of the installed firewall rules database.
Application List Current version of the application list. 
						

							
Access the Management and Diagnostic Console
34
Broadband Link - Summar y Page
The Broadband Link - Summary page allows you to view 2Wire gateway broadband connectivity-related 
settings, and reset the Broadband Link and IP Connection.
Note: The information displayed varies depending on whether the broadband connection is via 
DSL or Ethernet.
Features Item Description 
						

							
Access the Management and Diagnostic Console
35
Broadband Link - Statistics Page
The Broadband Link - Statistics page shows statistics associated with the 2Wire gateway broadband link. 
						

							
Access the Management and Diagnostic Console
36
Broadband Link - Detailed Statistics Page
The Broadband Link – Detailed DSL Statistics page shows a set of cumulative DSL statistics associated 
with the 2Wire gateway. 
						

							
Access the Management and Diagnostic Console
37
Broadband Link - Configuration Page
The Broadband Link – Configuration page allows you to m odify specific broadband connection settings.
For details on broadband link configuration settings, re fer to “Using Broadband Link Advanced Settings” on 
page 19. 
						

							
Access the Management and Diagnostic Console
38
Local Network - Status Page
The Local Network – Status page shows the status of the local network.
The Local Network – Status page includes the following information: Item Description
IP
Gateway The IP address allocated to the 2Wire gateway.
IP Network The IP address used by the network.
Subnet Mask The subnet mask allocated to the 2Wire gateway.
DHCP Range The range of IP addresses available on the network, the  number of addresses allocated, and the number of 
addresses remaining.
DHCP Timeout The time, in minutes , before the DHCP lease must be 
renewed.
Wireless (this field is present only on wireless 2Wire gateway models)