MSI G41m4-l Manual

							
2
MS-7592

BioS SetuP
Power  on  the  computer  and  the  system  will  start  PoSt  (Power on  Self test) 
process.  When  the  message  below  appears  on  the  screen,  press    key  to 
enter Setup.
Press deL to enter SetuP
if the message disappears before you respond and you still wish to enter Setup, 
restart  the  system  by  turning  it  oFF  and on  or  pressing  the  ReSet  button.  you 
may  also  restart  the  system  by  simultaneously  pressing  ,  ,  and   keys.
Main Page
Standard CMoS Features
use this menu for basic system configurations, such as time, date etc.
advanced BioS Features
use this menu to setup the items of special enhanced features.
integrated Peripherals
use this menu to specify your settings for integrated peripherals.
Power Management Setup
use this menu to specify your settings for power management.
H/W Monitor 
this entry shows the status of your CPu, fan, warning for overall system status.  
BioS Setting Password
use this menu to set BioS setting Password.
Cell Menu
use this menu to specify your settings for frequency/voltage control. 
						

							
22

Load Fail-Safe defaults
use this menu to load the BioS default values that are factory settings for system 
operations.
Load optimized defaults
use  this  menu  to  load  factory  default  settings  into  the  BioS  for  stable  system 
performance operations.
Save & exit Setup
Save changes to CMoS and exit setup.
exit Without Saving
abandon all changes and exit setup. 
						

							
2
MS-7592

Cell Menu
Current CPu/dRaM Frequency 
it shows the current frequency of CPu/Memory. Read-only.
intel eiSt
the enhanced  intel  SpeedStep  technology  allows  you  to  set  the  performance 
level  of  the  microprocessor  whether  the  computer  is  running  on  battery  or  aC 
power.  this field will appear after you installed the CPu which support speedstep 
technology.
adjust CPu FSB Frequency (MHz)
this item allows you to adjust the CPu FSB frequency.
adjusted CPu Frequency (MHz)
it shows the adjusted CPu frequency (FSB x Ratio). Read-only.
advance dRaM Configuration
Press  to enter the sub-menu.
dRaM timing Mode
Selects  whether  dRaM  timing  is  controlled  by  the  SPd  (Serial  Presence  de-
tect)  eePRoM on the  dRaM module. Setting to [auto By SPd] enables  dRaM 
timings and the following related items to be determined by BioS based on the 
configurations  on  the  SPd.  Selecting  [Manual]  allows  users  to  configure  the 
dRaM timings and the following related items manually.
CaS Latency (CL)
When  the  dRaM timing  Mode  sets  to  [Manual],  the  field  is  adjustable.  this 
controls  the  CaS  latency,  which  determines  the  timing  delay  (in  clock  cycles) 
before SdRaM starts a read command after receiving it. 
tRCd
When  the  dRaM timing  Mode  sets  to  [Manual],  the  field  is  adjustable.  When 
dRaM  is  refreshed,  both  rows  and  columns  are  addressed  separately.  this 
setup  item  allows  you  to  determine  the  timing  of  the  transition  from  RaS  (row  
						

							
24

address strobe) to CaS (column address strobe). the less the clock cycles, the 
faster the dRaM performance. 
tRP
When  the  dRaM timing  Mode  sets  to  [Manual],  the  field  is  adjustable.  this 
item  controls  the  number  of  cycles  for  Row  address  Strobe  (RaS)  to  be  al
-
lowed to precharge.  if insufficient time is allowed for the RaS to accumulate its 
charge  before  dRaM  refresh,  refreshing  may  be  incomplete  and  dRaM  may 
fail to retain data.  this item applies only when synchronous  dRaM is installed 
in the system.
tRaS
When the dRaM timing Mode sets to [Manual], the field is adjustable.  this set-
ting determines the time RaS takes to read from and write to a memory cell.
tRtP
When  the  dRaM timing  Mode  sets  to  [Manual],  the  field  is  adjustable.  time 
interval between a read and a precharge command.
tRFC
When the dRaM timing Mode sets to [Manual], the field is adjustable.  this set-ting determines the time RFC takes to read from and write to a memory cell.  
tWR
When the dRaM timing Mode is set to [Manual], the field is adjustable.  it speci-fies the amount of delay (in clock cycles) that must elapse after the completion 
of a valid write operation, before an active bank can be precharged.  this delay 
is  required  to  guarantee  that  data  in  the  write  buffers  can  be  written  to  the memory cells before precharge occurs.
tRRd
When the dRaM timing Mode sets to [Manual], the field is adjustable. Speci-fies the active-to-active delay of different banks. 
tWtR
When  the  dRaM timing  Mode  is  set  to  [Manual],  the  field  is  adjustable.  this 
item controls the Write  data in to Read Command  delay memory timing.  this 
constitutes  the  minimum  number  of  clock  cycles  that  must  occur  between  the last valid write operation and the next read command to the same internal bank 
of the ddR device. 
FSB/dRaM Ratio
this item will allow you to adjust the ratio of FSB to memory.
adjusted dRaM Frequency (MHz)
it shows the adjusted memory frequency. Read-only.
adjust PCi-e Frequency (MHz)
this item allows you to adjust the PCi-e frequency.
auto disable dRaM/PCi Frequency
When set to [enabled], the system will remove (turn off) clocks from empty  diMM 
and PCi slots to minimize the electromagnetic interference (eMi). 
						

							
25
MS-7592

Spread SpectrumWhen  the  motherboard’s  clock  generator  pulses,  the  extreme  values  (spikes)  of 
the pulses create eMi (electromagnetic  interference). the Spread Spectrum func-
tion  reduces  the  eMi  generated  by  modulating  the  pulses  so  that  the  spikes  of 
the  pulses  are  reduced  to  flatter  curves.  if  you  do  not  have  any eMi  problem, 
leave  the  setting  at  disabled  for  optimal  system  stability  and  performance.  But  if 
you are plagued by  eMi, set to enabled for  eMi reduction. Remember to disable 
Spread Spectrum if you are overclocking because even a slight jitter can introduce a temporary boost in clock speed which may just cause your overclocked proces-sor to lock up.
iMPoRtant
if you do not have any  eMi problem, leave the setting at [disabled] for optimal 
system  stability  and  performance.  But  if  you  are  plagued  by  eMi,  select  the 
value of Spread Spectrum for eMi reduction. 
the greater the Spread Spectrum value is, the greater the  eMi is reduced, and 
the  system  will  become  less  stable.  For  the  most  suitable  Spread  Spectrum 
value, please consult your local eMi regulation.
Remember to disable Spread Spectrum if you are overclocking because even a slight jitter can introduce a temporary boost in clock speed which may just cause your overclocked processor to lock up.
*
*
* 
						

							
26
Load optimized defaults
you can load the default values provided by the mainboard manufacturer for the 
stable performance. 
						

							
27
MS-7592
한국어 
시작하기
G4M4 시리즈 (MS-7592 v.x) Micro-atX 메인보드를 선택해주셔서 감사합니다. 
G4M4  시리즈는  최적의  시스템  효율을  위해 intel®  G4  & iCH7  칩셋에  기반을 둔 제품입니다. 고급의 intel® Core™2  quad/ intel® Core™2  duo/ intel® Pentium / intel® Core™2  extreme LGa775  프로세서에 적합하게 디자인된 G4M4 시리즈는 고성능과 전문적인 데스크톱 플랫폼 솔루션을 제공합니다.
레이아웃
B AT T+
P CI 2P CI 1
P C I _ E 1
J T P M1
S Y S FA N1S Y S FA N2
C P U FA N1
J P W 1
J C O M1
I n t elG 41
I n t elI C H 7
J BJ C I 1AT1
J U S B1 JU S B 2
C D _ I N1
J A U D 1JS P D1F DD 1S ATA1 S
ATA 3
S ATA2 S
ATA 4
J F P 2
I D E 1
ATX1
D I M M
1
D I M M
2
J F P 1
Top : m o u se B o t t o m:k e y b o a r d
Top : P a r a l l el P o r tB o t t o m: C OM p o r tV GA p o rt
Top: LA N Ja ckB o t t o m : US B p o r t s 
 US B po r t s 
T:M :B :L i n e - InL i n e - O u tM icT:R S - O u tM :C S - O u tB : S S - O u t 
						

							
28

지원되는 프로세서LGa 775 패키지의 intel®  Pentium e2XXX/ Core 2 dual/ Core 2 quad/ Wolf-
dale/ yorkfield 프로세서
팬 속도 컨트롤이 있는 4 핀 CPu 팬 핀 헤더 지원
FMB 05a@95W 지원(CPu에 대한 최신 정보는http://global.msi.com.tw/index.php?func=cpuform2 참조)
지원되는 FSB 최대  MHz 지원  
칩셋노스 브릿지: intel® G4 칩셋
사우스 브릿지: intel® iCH7 칩셋
지원되는 메모리 ddR2 667/800 SdRaM (최대 8GB)
2 ddR2 diMMs (240핀/ .8V)
(호환 가능한 부품에 대한 자세한 내용은http://global.msi.com.tw/index.php?func=testreport 를 참조하십시오.)
LanRealtek® RtL 8dL에 의해 Lan 0/00/000 고속 이더넷 지원 (옵션)Realtek® RtL 80eL에 의해 Lan 0/00 고속 이더넷 지원 (옵션)
오디오Realtek® aLC888S에 의해 통합된 칩
7.채널 오디오 출력 지원
azalia .0 Spec 과 호환
ide intel® iCH7에 의한 ide 포트 개
ultra dMa /66/00, Pio 및 버스 마스터 작동 모드 지원
Sata intel® iCH7 에 의한 Sataii 포트 4개
최대 .0 Gb/s 의 저장 및 데이터 전송 지원
플로피 플로피 포트 개
 Fdd with 60kB, 720kB, .2MB, .44MB 및 2.88MB 지원
커넥터후면 패널PS/2 마우스 포트 개 
PS/2 키보드 포트 개
CoM 포트 개
VGa 포트 개
SPP/ePP/eCP 모드를 지원하는 병렬 포트 개
uSB 2.0 포트 4개
Lan 잭 개
플렉시블 오디오 잭 /6 개 (옵션)
■
■■
■
■■
■■
■■
■■■
■■
■■
■■
■‑‑‑‑‑‑‑‑
사양 
						

							
29
MS-7592

온보드 핀헤더/커넥터uSB 2.0 핀헤더 2개 
시리얼 포트 핀헤더 개 
SPdiF 출력 핀헤더 개
전면 패널 오디오 핀헤더 개
섀시 침입 핀헤더 개
Cd 입력 핀헤더 개
tPM 핀헤더 개
슬롯 PCi express x6 슬롯 개
PCi 슬롯 2개, .V/ 5V PCi 버스 인터페이스 지원
폼 팩터Micro-atX (24.4cm X 9. cm)
장착 장착 구멍 6개
■‑‑‑‑‑‑‑
■■
■
■ 
						

							
0

뒷면
뒷면에는 다음 커넥터가 있습니다:
LGa 775 CPu의 핀 패드 면
LGa 775 CPu의 표면
열이 잘 발산되도록 서멀 페이스트를 표면에 약간 바르십시오.
주의: 개의 오디오 잭이 있는 메인보드를 구입하면 8 채널 음향 효과를 달성하기 위해  제 7 과 8 채널은 전면 패널에서 출력해야 합니다.
하드웨어 설치
이 장에서는 CPu, 메모리 모듈, 확장 카드의 설치 방법과 메인보드의 점퍼 설정 방법을 설명합니다. 또한 마우스, 키보드 등과 같은 주변 장치의 연결 방법을 설명합니다. 설치하는 동안, 부품을 주의해서 취급하고 설치 절차를 잘 따르십시오.
LGa775의 CPu 및 쿨러 설치 절차
CPu  설치  시  과열을  방지하는  쿨러를  상단에  연결하십시오.  CPu  쿨러가  없으면  
컴퓨터 시작하기 전에 지역 대리점에 연락하십시오.
PS/2 마우스
PS/2 키보드 
병렬 포트
시리얼 포트  VGa 포트  uSB 포트 Lan
라인 입력
라인 출력 
MiC
RS 출력
CS 출력 
SS 출력 
      정렬 키      정렬 키
노란색 삼각형은 핀 의 표시기입니다.노란색 삼각형은 핀 의 표시기입니다.
   (옵션)