Netgear Readynas 628x Ultimate Performance Business Data Storage 8 Bay Hardware Manual

							Make sure that the HDD mounting holes are aligned with the bracket's mounting posts and that the HDD
connectors face the interior of the disk tray.
Disks
131
ReadyNAS OS 6.5 
						

							8.Push the mounting bracket and HDD back into the disk tray.
WARNING:
To prevent damage to your system, make sure that the disk tray is correctly
oriented before inserting it into the drive bay.
9.Insert the disk tray back into the drive bay of the storage system.
•For 2-bay and 4-bay systems, insert the disk tray so that the disk tray release latch is near the bottom
of the system.
•For 6-bay systems, insert the disk tray so that the disk tray release latch is on the left side of the
system.
10.Press down on the disk tray handle until it latches closed.
The disk tray is secured in the drive bay.
If the volume that contained the failed disk uses a protected RAID configuration, the system automatically
resynchronizes the volume using the new disk. Resynchronization might take several hours, depending
on the disk size.You can continue to use your storage system, although access is slower until the
volume resynchronization finishes.
Disks
132
ReadyNAS OS 6.5 
						

							For more information about RAID configurations, see the ReadyNAS OS 6 Software Manual, which is
available at support.netgear.com/product/ReadyNAS-OS6.
Replace a 2.5-Inch Disk
To replace a 2.5-inch hard disk drive (HDD) or 2.5-inch solid state drive (SSD):
1.If necessary, slide the recessed handle lock to the unlocked position.
2.Press the disk tray release latch.
The tray handle pops out.
3.Pull out the disk tray.
4.Replace the 2.5-inch HDD or SSD:
Disks
133
ReadyNAS OS 6.5 
						

							a.Remove the screws and the old 2.5-inch HDD or SSD.
b.Place the new 2.5-inch HDD or SSD in the disk tray.
c.Secure the HDD or SSD to the disk tray using the screws.
Make sure that the disk connectors face the interior of the disk tray.
Disks
134
ReadyNAS OS 6.5 
						

							Make sure that the HDD or SSD is installed on the correct side of the disk tray.
WARNING:
To prevent damage to your system, make sure that the disk tray is correctly
oriented before inserting it into the drive bay.
5.Insert the disk tray back into the drive bay of the storage system.
•For 2-bay and 4-bay systems, insert the disk tray so that the disk tray release latch is near the bottom
of the system.
•For 6-bay systems, insert the disk tray so that the disk tray release latch is on the left side of the
system.
6.Press down on the disk tray handle until it latches closed.
The disk tray is secured in the drive bay.
If the volume that contained the failed disk uses a protected RAID configuration, the system automatically
resynchronizes the volume using the new disk. Resynchronization might take several hours, depending
on the disk size.You can continue to use your storage system, although access is slower until the
volume resynchronization finishes.
For more information about RAID configurations, see the ReadyNAS OS 6 Software Manual, which is
available at support.netgear.com/product/ReadyNAS-OS6.
Disks
135
ReadyNAS OS 6.5 
						

							A
Defaults and Technical Specifications
This appendix includes the following sections:
•Factory Default Settings on page 137
•ReadyNAS 102 Technical Specifications on page 137
•ReadyNAS 104 Technical Specifications on page 138
•ReadyNAS 202 Technical Specifications on page 140
•ReadyNAS 212 Technical Specifications on page 141
•ReadyNAS 204 Technical Specifications on page 142
•ReadyNAS 214 Technical Specifications on page 143
•ReadyNAS 312 Technical Specifications on page 144
•ReadyNAS 314 Technical Specifications on page 146
•ReadyNAS 316 Technical Specifications on page 147
•ReadyNAS 516 Technical Specifications on page 148
•ReadyNAS 526X Technical Specifications on page 150
•ReadyNAS 626X Technical Specifications on page 151
•ReadyNAS 716X Technical Specifications on page 152
•EDA 500 Technical Specifications on page 154
•Safety Warnings on page 155
136 
						

							Factory Default Settings
The following table lists factory default settings for ReadyNAS OS 6 desktop storage systems.
Table 14. ReadyNAS OS 6 factory default settings
DefaultFeature
Login
The default IP address for the ReadyNAS is assigned by
the local router (DHCP server).
If a router does not assign an IP address, the ReadyNAS
defaults to the IP address https://169.254.x.x, where the
last two octets are randomly generated based on the
system's MAC address.
Default IP address
adminAdmin user name (case-sensitive)
passwordAdmin login password (case-sensitive)
Management
ReadyNAS local admin page web-based configuration and
status monitoring
System configuration
ReadyCloud for Windows, Mac, and LinuxDiscovery, setup, and multi-storage system
status monitoring web
LAN Connections
See product labelMAC address
1500MTU size
Auto Sense 10/100/1000BASE-T, RJ-45Ethernet port
DHCP acquiredLAN IP address
ReadyNAS 102 Technical Specifications
The ReadyNAS 102 storage system meets the following technical specifications:
General:
•Marvell Armada 370 1.2 GHz CPU
•512 MB memory
•Two-bay storage
•One eSATA port
Defaults and Technical Specifications
137
ReadyNAS OS 6.5 
						

							•One USB 2.0 port (front)
•Two USB 3.0 ports (back)
•One GbE port
Physical dimensions (h x w x d):
142 x 101 x 220 mm (5.60 x 3.98 x 8.70 in.)
Physical weight:
2.12 kg (4.67 lb) without disks
Power consumption:
•BTU at full power supply utilization: 31.7W
•In operation: 31W
•Power off (Wake On LAN): 1.0W
•Power off: 210 mW
Electrical:
•External 60 W (12V, 5A) AC power supply
•Input: 100-240V AC, 50/60 Hz
Environmental requirements:
•Operating temperature: 0 to 40°C (32° to 104°F)
•Operating humidity: 20 to 80% relative humidity (noncondensing)
•Storage temperature: -20 to 70°C (-4 to 158°F)
•Storage humidity: 5 to 95% relative humidity (noncondensing)
•Software-controlled 92 mm chassis cooling fan
Certifications:
FCC Class B, CE Class B, RoHS, VCCI Class B
ReadyNAS 104 Technical Specifications
The ReadyNAS 104 storage system meets the following technical specifications:
Defaults and Technical Specifications
138
ReadyNAS OS 6.5 
						

							General:
•Marvell Armada 370 1.2 GHz CPU
•512 MB memory
•Four-bay storage
•One eSATA port
•One USB 2.0 port (front)
•Two USB 3.0 ports (back)
•Two GbE ports
•LCD display
Physical dimensions (h x w x d):
205 x 134 x 223 mm (8.97 x 5.28 x 8.78 in.)
Physical weight:
4.70 kg (10.36 lb) without disks
Power consumption:
•BTU at full power supply utilization: 47W
•In operation: 45.6W
•Power off (Wake On LAN): 1.4W
•Power off: 0.44 W
Electrical:
•External 90 W (12V, 7A) AC power supply
•Input: 100-240VAC, 50/60 Hz
Environmental requirements:
•Operating temperature: 0 to 40°C (32° to 104°F)
•Operating humidity: 20 to 80% relative humidity (noncondensing)
•Storage temperature: -20 to 70°C (-4 to 158°F)
•Storage humidity: 5 to 95% relative humidity (noncondensing)
•Software-controlled 92 mm chassis cooling fan
Defaults and Technical Specifications
139
ReadyNAS OS 6.5 
						

							Certifications:
FCC Class B, CE Class B, RoHS, VCCI Class B
ReadyNAS 202 Technical Specifications
The ReadyNAS 202 storage system meets the following technical specifications:
General:
•Annapurna Labs AL212 1.4 GHz processor
•2 GB memory
•Two-bay storage
•One eSATA port
•One USB 3.0 port (front)
•Two USB 3.0 ports (back)
•Two GbE ports
Physical dimensions (h x w x d):
142 x 101 x 220 mm (5.60 x 3.98 x 8.70 in.)
Physical weight:
2.12 kg (4.67 lb) without disks
Power consumption:
•BTU at full power supply utilization: 39.5W
•In operation: 38W
•Power off (Wake On LAN): 1.31W
Electrical:
•External 60 W (12V, 5A) AC power supply
•Input: 100-240 VAC, 50/60 Hz
Defaults and Technical Specifications
140
ReadyNAS OS 6.5