Panasonic Bb Gt1500 Operating Instructions Manual

							Important Information
11For product assistance, visit www.panasonic.com/help
For A assistance, visit www.joip.com
shock. Confirm that smoke has 
stopped emitting and contact the 
Panasonic Call Center at 1-800-211-
PANA (1-800-211-7262).
LDo not spill liquids (detergents, 
cleansers, etc.) onto the telephone 
line cord plug, or allow it to become 
wet at all. This may cause a fire. If the 
telephone line cord plug becomes 
wet, immediately pull it from the 
telephone wall jack, and do not use.
LDo not place or use this product near 
automatically controlled devices such 
as automatic doors and fire alarms. 
Radio waves emitted from this product 
may cause such devices to 
malfunction resulting in an accident.
LCompletely insert the AC 
adaptor/power plug into the power 
outlet. Failure to do so may cause 
electric shock and/or excessive heat 
resulting in a fire.
LRegularly remove any dust, etc. from 
the AC adaptor/power plug by pulling 
it from the power outlet, then wiping 
with a dry cloth. Accumulated dust 
may cause an insulation defect from 
moisture, etc. resulting in a fire.
CAUTION:
Installation
LNever install telephone wiring during a 
lightning storm.
LNever install telephone line jacks in 
wet locations unless the jack is 
specifically designed for wet 
locations.
LNever touch uninsulated telephone 
wires or terminals unless the 
telephone line has been disconnected 
at the network interface.
LUse caution when installing or 
modifying telephone lines.
LDo not touch the plug with wet hands.LThe AC adaptor is used as the main 
disconnect device. Ensure that the AC 
outlet is installed near the product and 
is easily accessible.
Battery
To reduce the risk of fire or injury to 
persons, read and follow these 
instructions.
LUse only the battery(ies) specified.
LDo not dispose of the battery(ies) in a 
fire, as they may explode. Check with 
local waste management codes for 
special disposal instructions.
LDo not open or mutilate the 
battery(ies). Released electrolyte is 
corrosive and may cause burns or 
injury to the eyes or skin. The 
electrolyte may be toxic if swallowed.
LExercise care when handling the 
battery(ies). Do not allow conductive 
materials such as rings, bracelets or 
keys to touch the battery(ies), 
otherwise a short circuit may cause 
the battery(ies) and/or the conductive 
material to overheat and cause burns.
LCharge the battery(ies) provided, or 
identified for use with the product only, 
in accordance with the instructions 
and limitations specified in this 
manual.Medical
LConsult the manufacturer of any 
personal medical devices, such as 
pacemakers or hearing aids, to 
determine if they are adequately 
shielded from external RF (radio 
frequency) energy. (The product 
operates in the frequency range of 
5.74 GHz to 5.84 GHz, and the power 
output is 200 mW (max.).) Do not use 
the product in health care facilities if 
any regulations posted in the area 
instruct you not to do so. Hospitals or 
health care facilities may be using 
GT15xx.book  Page 11  Monday, June 4, 2007  8:52 AM 
						

							Important Information
12For product assistance, visit www.panasonic.com/help
For A assistance, visit www.joip.com
equipment that could be sensitive to 
external RF energy.
For best performance
Base unit location/avoiding noise
The base unit and other compatible 
Panasonic units use radio waves to 
communicate with each other.
LFor maximum coverage and noise-
free communications, place your base 
unit:
– at a convenient, high, and central 
location with no obstructions 
between the handset and base unit 
in an indoor environment.
– away from electronic appliances 
such as TVs, radios, personal 
computers, wireless devices or 
other phones.
– avoid facing radio frequency 
transmitters, such as external 
antennas of mobile phone cell 
stations (avoid putting the base unit 
on a bay window or near a window).
LCoverage and voice quality depends 
on the local environmental conditions.
LIf the reception for a base unit location 
is not satisfactory, move the base unit 
to another location for better 
reception.
Environment
LKeep the product away from electrical 
noise generating devices, such as 
fluorescent lamps and motors.LThe product should be kept free from 
excessive smoke, dust, high 
temperature, and vibration.
LThe product should not be exposed to 
direct sunlight.
LDo not place heavy objects on top of 
the product.
LWhen you leave the product unused 
for a long period of time, unplug the 
product from the power outlet.
LThe product should be kept away from 
heat sources such as heaters, kitchen 
stoves, etc. It should not be placed in 
rooms where the temperature is less 
than 5 °C (41 °F) or greater than 40 °C 
(104 °F). Damp basements should 
also be avoided.
LThe maximum calling distance may be 
shortened when the product is used in 
the following places: Near obstacles 
such as hills, tunnels, underground, 
near metal objects such as wire 
fences, etc.
LOperating the product near electrical 
appliances may cause interference. 
Move away from the electrical 
appliances.
Routine care
LWipe the outer surface of the product 
with a soft moist cloth. Do not use 
benzine, thinner, or any abrasive 
powder. No responsibility will be taken by our 
company with respect to 
consequences resulting from the 
inappropriate use, damage or both of 
the unit.
GT15xx.book  Page 12  Monday, June 4, 2007  8:52 AM 
						

							Important Information
13For product assistance, visit www.panasonic.com/help
For A assistance, visit www.joip.com
Security caution
When using this product, take 
appropriate measures to avoid the 
following security breaches.
LLeaks of private information via this 
product
LIllegal use of this product by a third 
party
LInterference or suspension of the use 
of this product by a third party
Take the following measures to avoid 
security breaches:
LTo prevent illegal access, keep the 
base unit software updated (if you do 
not have the latest version of 
software, this can lead to blocked 
access or information leaks) (page 
55).
LYou are responsible for the security 
settings, such as the remote code for 
the answering system, to access this 
product. This information should not 
be made available to any third parties 
outside the user group. To prevent 
unauthorized access to this product, 
we recommend that you regularly 
change the remote code (page 63).
LPlace this product where it is unlikely 
to be stolen.
LDuring an internet call, outside 
interference may occur resulting in 
improper call transmission and/or unit 
function.
Notice for product disposal, transfer, 
or return
LThis product can store your 
private/confidential information. To 
protect your privacy/confidentiality, we 
recommend that you erase the 
information such as phonebook or 
caller list entries from the memory before you dispose, transfer or return 
the product.
– Erasing caller list information (page 
45)
– Erasing phonebook information 
(page 41)
– Erasing messages (page 59, 72)
LWhen transferring this product to 
another party or disposing of this 
product, be sure to cancel the service 
contract with A at www.joip.com if 
you subscribed to optional A 
services.
GT15xx.book  Page 13  Monday, June 4, 2007  8:52 AM 
						

							Preparation
14For product assistance, visit www.panasonic.com/help
For A assistance, visit www.joip.com
Controls (Base unit)
BB-GT1500
AIP indicator
BTEL indicator
CSTATUS indicator
DVM (Voice Mail) indicatorECharge contacts
F{HANDSET LOCATOR}*1
G{IP RESET}
*1 You can locate a misplaced handset by pressing {HANDSET LOCATOR}. To stop 
paging, press it again or {OFF} on the handset.
AB DC
F
E
IP RESET
G Bottom view
GT15xx.book  Page 14  Monday, June 4, 2007  8:52 AM 
						

							Preparation
15For product assistance, visit www.panasonic.com/help
For A assistance, visit www.joip.com
BB-GT1540
A {IP} (IP line)
IP indicator
B {TEL} (Landline)
TEL indicator
C {IP/TEL}
D STATUS indicator
E VM (Voice Mail) indicator
F {ANSWER ON}
ANSWER ON indicator
G {LOCATOR} {INTERCOM}
H {AUTO} {PROGRAM}
I {CONF} (Conference)
J {HOLD}
K Speaker
L Charge contacts
M {*} (TONE)N {PAUSE} {REDIAL}
O {FLASH} {CALL WAIT}
P {MUTE}
Q {s} (SP-PHONE)
SP-PHONE indicator
R MIC (Microphone)
S Navigator key ({^} {V} {})
T {6} (Message)
Message indicator
U {STOP}
V {ERASE}
W {MEMO}
X {GREETING REC} (Recording)
Y {GREETING CHECK}
Z Display
! {IP RESET}
IP RESET
ABDCFE
RH
IJG
MNKOPQTU
!
S LVXYWZBottom view
GT15xx.book  Page 15  Monday, June 4, 2007  8:52 AM 
						

							Preparation
16For product assistance, visit www.panasonic.com/help
For A assistance, visit www.joip.com
Controls (Handset)
ASpeaker
BSoft keys
CHeadset jack
D{IP} (IP line)
EJoystick
F{s} (SP-PHONE)
G{REDIAL} {PAUSE}
H{*} (TONE)
I{FLASH} {CALL WAIT}
JCharge indicator
Ringer indicator
Message indicator
KReceiver
LDisplay
M{TEL} (Landline)
N{OFF}
O{HOLD} {INTERCOM}
PMicrophone
QCharge contacts
Using the joystick
The handset joystick can be used to 
navigate through menus and to select 
items shown on the display, by pushing it 
up {^}, down {V}, left {}.
The joystick can be used to select the 
center soft key icon, by pressing down 
on the center of the joystick.
Using the soft keys
The handset features 2 soft keys and a 
joystick. By pressing a soft key, or by 
pressing the center of the joystick, you 
can select the feature shown directly 
above it on the display.
AJ
B
M
N
O
P
Q
K
L
B
D
E
F
G
H
I
C
GT15xx.book  Page 16  Monday, June 4, 2007  8:52 AM 
						

							Preparation
17For product assistance, visit www.panasonic.com/help
For A assistance, visit www.joip.com
Installation
Connecting to a landline and the Internet (IP line)
Connect the base unit to a broadband router or modem with a built-in router.
*1 Computer is not required for setup or making/answering internet calls.
1Connect the included Ethernet cable to the “LAN” port on the base unit and 
unused Ethernet (LAN) port on your router or modem with a built-in router.
2Connect the included telephone line cord until it clicks into the “TEL” port on the 
base unit and telephone line jack.
3Connect the included AC adaptor to the base unit by pushing the plug firmly, then 
plug the other end into the power outlet.
LUse only the included Panasonic AC adaptor PQLV203.
LThe STATUS indicator on the base unit lights in red for about 3 seconds (page 
22).
Hook
(120 V AC, 60 Hz)
To single-line 
telephone jack 
(RJ11C) AC adaptor
3
Telephone 
line cordEthernet cableRouter
Computer
(Optional) *1Cable or 
DSL modemInternet
Press
plug firmly.
TEL
LAN
1
2
GT15xx.book  Page 17  Monday, June 4, 2007  8:52 AM 
						

							Preparation
18For product assistance, visit www.panasonic.com/help
For A assistance, visit www.joip.com
4Install the battery:
Press the notch of the handset cover firmly, and slide it in the direction of the 
arrow (A). Insert the battery (B), and press it down until it snaps into position 
(C). Then close the handset cover (D, E).
5Charge the battery:
Place the handset on the base unit.
LIf “Charge for 7 HRS” is displayed, wait for at most 15 minutes until 
“Please read joip Terms of Use. Agree?” is displayed.
LTo fully charge the battery, place the handset on the base unit for 7 hours. For 
battery information, see page 20.
6Agree to the A Terms of Use:
To use the A IP line, read the Terms of Use for the A services on the 
included leaflet or at www.joip.com then press {YES} (left soft key) while 
“Please read joip Terms of Use. Agree?” is displayed.
LTo agree to the Terms of Use later, press {NO}. When you want to agree, 
press {IP} and wait until the display changes from “Free calls! Plug 
internet cable. www.joip.com” to “Please read joip Terms of 
Use. Agree?”. Press {YES} to agree to it.
7Check for Internet access:
Wait until the STATUS indicator on the base unit turns green.
– When the STATUS indicator on the base unit lights in green, the installation is 
complete. Your A number is displayed on the handset 1 (included with your 
base unit). Once you start operations with the handset, it disappears from the 
display (page 30).
C
ED
A
B
Confirm the charge
indicator is on.
Model shown is BB-GT1500.
[
Please read joip
Terms of Use.
Agree?
YESNO
GT15xx.book  Page 18  Monday, June 4, 2007  8:52 AM 
						

							Preparation
19For product assistance, visit www.panasonic.com/help
For A assistance, visit www.joip.com
– When the STATUS indicator on the base unit does not light in green even if you 
wait for a few minutes, see page 23.
Note:
LThe AC adaptor must remain connected at all times. (It is normal for the adaptor to 
feel warm during use.)
LThe AC adaptor should be connected to a vertically oriented or floor-mounted AC 
outlet. Do not connect the AC adaptor to a ceiling-mounted AC outlet, as the 
weight of the adaptor may cause it to become disconnected.
LThe unit will not work during a power failure. To use the landline, we recommend 
connecting a corded telephone to the same telephone line or to the same 
telephone line jack using a Panasonic T-adaptor (page 8).
For DSL service users k
If the base unit is connected to a landline with DSL service, please attach a noise 
filter (contact your DSL provider) to the telephone line between the base unit and the 
telephone line jack in the event of the following:
– Noise is heard during conversations using the landline.
– Caller ID features do not function properly for landline calls.
Model shown is 
BB-GT1500.
Amber      Green
joip:#1001060429
 
Yo u r  A number
Noise filter
To single-line 
telephone 
jack (RJ11C)
GT15xx.book  Page 19  Monday, June 4, 2007  8:52 AM 
						

							Preparation
20For product assistance, visit www.panasonic.com/help
For A assistance, visit www.joip.com
Battery charge
Battery charge
To fully charge the battery, place the 
handset on the base unit for 7 hours.
LWhile charging, the charge indicator 
on the handset lights in amber. When 
the battery is fully charged, the 
indicator lights in green.
LModel shown is BB-GT1500.
Note:
LIf you want to use the handset 
immediately, charge the battery for at 
least 15 minutes.
LTo ensure that the battery charges 
properly, clean the charge contacts of 
the handset and base unit with a soft, 
dry cloth once a month. Clean more 
often if the unit is subject to the 
exposure of grease, dust, or high 
humidity.
Battery level
Note:
LWhen the battery needs to be 
charged, the handset beeps 
intermittently during use.
Panasonic battery performance
Note:
LBattery operating time may be 
shortened over time depending on 
usage conditions and surrounding 
temperature.
LBattery power is consumed whenever 
the handset is off the base unit, even 
when the handset is not in use.
LAfter the handset is fully charged, 
displaying “Charge completed”, it 
may be left on the base unit without 
any ill effect on the battery.
LThe battery level may not be 
displayed correctly after you replace 
the battery. In this case, place the 
Charge
contacts
Battery 
iconBattery level
1Fully charged
2Medium
3Low
Flashing: needs to be 
recharged.
4Empty
OperationOperating time
While in use 
(talking)Up to 6 hours
While not in use 
(standby)Up to 14 days
While using the 
clarity booster 
feature (page 
33)Up to 4 hours
GT15xx.book  Page 20  Monday, June 4, 2007  8:52 AM