Panasonic Bb Hcm311a Owners Manual

							Operating Instructions (Additional Features)
[For assistance, please call: 1-800-272-7033] 31
 Clicking [].
 Clicking [
						

							Operating Instructions (Additional Features)
32
7.Set the image buffer frequencies, and click [Next>].
Note
Due to the network environment, object, number of accesses, enabling IPsec, 
the camera may not record the numbers of images as you set. In this case, set 
the image buffer frequencies longer.
 Clicking [Cancel] takes you back to the Trigger page without saving 
changes.
 Clicking [
						

							Operating Instructions (Additional Features)
[For assistance, please call: 1-800-272-7033] 33
8.Select the transfer method, and click [Next>].
 Clicking [
						

							Operating Instructions (Additional Features)
34
When you set [FTP] for Transfer Method
Select [FTP], and click [Next>]. The following page is displayed.
 Clicking [
						

							Operating Instructions (Additional Features)
[For assistance, please call: 1-800-272-7033] 35
SettingDescription
Server IP 
Address or 
Host Name
*1
*1But [Space], [], [], [&], [] are not available.
 If you set the server IP address, set 4 digits (0—255) and 3 
periods such as 192.168.0.253. But 0.0.0.0 and 
255.255.255.255 are not available. Or set a host name (1—
255 characters).
 You can set IPv6 address.
Po r t N o. Enter a number (1—65535). Usually set to 21.
Login ID*2
*2But [] is not available.
 If your ISP requires a login ID, set it (0—63 characters).
Password*2 If your ISP requires a password, set it (0—63 characters).
Login Timing Select the login timing to an FTP server. If you set [One Time] 
during 1-minute transfer, the camera logs in to the server only 
once, and can reduce the time to log in or log out.
Upload File 
Name*1 Set the file name to save on an FTP server. Enter 1—232 
characters. Entering \ creates directories for a file. (E.g. 
NetworkCamera\image.jpg)
Overwrite 
Setting Selecting [Overwrite File] saves and overwrites the image on 
the server. Selecting [Save as New File with Time Stamp] 
saves the image attaching time stamps on the file name, and 
the images are not overwritten.
(E.g. image20050101093020500.jpg) Underlined numbers 
are 9h30min20s500ms on January 1, 2005. The letter s is 
inserted after the day when referring to a summer time zone.
Data 
Tr a n s f e r  
Method Select [Passive Mode] normally. If FTP does not work, select 
[Active Mode] and check the operation. 
						

							Operating Instructions (Additional Features)
36
When you set [E-mail] for Transfer Method
Select [E-mail], and click [Next>]. The following page is displayed.
 Clicking [
						

							Operating Instructions (Additional Features)
[For assistance, please call: 1-800-272-7033] 37
SettingDescription
SMTP Server IP 
Address or Host 
Name
*1
*1But [Space], [], [], [&], [] are not available.
 If you set the server IP address, set 4 digits (0—255) and 
3 periods such as 192.168.0.253. But 0.0.0.0 and 
255.255.255.255 are not available. Or set a host name 
(1—255 characters).
 You can set IPv6 address.
Po r t N o. Enter a number (1—65535). Usually set to 25.
POP3 Server IP 
Address or Host 
Name
*1
 If you set the server IP address, set 4 digits (0—255) and 
3 periods such as 192.168.0.253. But 0.0.0.0 and 
255.255.255.255 are not available. Or set a host name 
(0—255 characters).
 You can set IPv6 address.
Po r t N o. Enter a number (1—65535). Usually set to 110.
Login ID*2
*2But [] is not available.
 If your ISP requires a login ID to log in to a POP3 server, 
set it (0—63 characters).
Password*2 If your ISP requires a password to log in to a POP3 server, 
set it (0—63 characters).
Reply E-mail 
Address*2 Set the senders E-mail address. We recommend you to 
set the administrators E-mail address.
Destination E-
mail Address*2 
1—3
 Set the destination E-mail address (up to 3).
Subject*2 Enter a subject with ASCII characters or characters in each 
language (0—44 characters for a 1-byte character and 0—
22 characters for a 2-byte character).
Te x t Enter text with ASCII characters or characters in each 
language (0—63 characters for a 1-byte character and 0—
31 characters for a 2-byte character). But [] and [end-of-
line] key are not available. 
						

							Operating Instructions (Additional Features)
38
9.After you confirm the settings and click [Next>], set E-mail notification and click 
[Next>].
 If you select [Enable], the E-mail Notification When Triggered page is 
displayed. Enter the settings seeing page 
36 and page 37.
10.Click [Save] after confirming the settings.
 New settings are saved.
 When finished, Success! is displayed.
SettingDescription
Disable The camera does not send an E-mail notification when 
buffering or transferring image.
Enable The camera sends an E-mail notification (up to 3 
destinations) when buffering or transferring image. 
						

							Operating Instructions (Additional Features)
[For assistance, please call: 1-800-272-7033] 39
11.Click [Go to Trigger page].
 The Trigger page is displayed.
Note
 If you set a short interval to transfer image to a cell phone, many E-mails 
may be sent to it leading to a large phone bill. Therefore, we recommend 
you to set a long interval. 1 image per minute frequency is recommended.
 Motion Detection transfer stops its operations until the camera finishes all 
transfers. For example, if the camera transfers 3 images per minute and 6 
images in total, the Motion Detection will be in the following operation.
 If you are buffering images on the internal memory, the following 
operations also delete all buffered images.
– Turning off the camera.
– Saving the Date and Time page.
– Restarting, updating firmware or resetting the camera to factory 
default.
– Maximum number of buffered images change depending on 
resolution, image quality and what object the camera buffers. At the 
320 x 240 pixels resolution and the standard quality, the camera 
buffers about 125 frames. (If 3 triggers are enabled [maximum 5 
triggers], the internal memory capacity is divided into 3 sections. In 
this case, each trigger can buffer about 40 images.) See 3.11 File 
Size and Number of Buffered Images on the Operating Instructions 
for the internal memory capacity.
Note
 A change due to light or wind may detect motions mistakenly.
 Motion detection level is changed depending on resolution, image quality, 
and object situation. Confirm the level by performing motion detection 
recording.
 Enabling Motion Detection delays the frame rate of the camera.
 Objects moving fast may not be detected.
 Motion Detection may not work in the dark. 
Detectable DetectableUndetectable
1st 2nd 3rd 4th 5th 6th120 seconds
A Motion Detection signal is detected. 
						

							Operating Instructions (Additional Features)
40
Setting the Motion Detection
The Motion Detection page allows you to adjust sensitivity of the Motion Detection. 
Threshold: If the threshold is set low, this function sensitively detects changes.
Sensitivity: If you set sensitivity high, amplitude of motion detection bar gets jumpy.
1.Click [Motion Detection] on the Setup page.
2.Click the Motion Detection bar in Threshold to set the threshold level.
3.Click the Motion Detection bar in Sensitivity to set the sensitivity level.
4.Click [Save] to save the settings.
 Clicking [Cancel] cancels your settings without saving changes.
5.Click [Go to Motion Detection page].
 The Motion Detection page is displayed.
Note
 The Motion Detection is disabled while panning and tilting.
 The Motion Detection is disabled while zooming (BB-HCM381A).
Preview
Display current threshold and detection level.
 The threshold is displayed by between green and red bar.
 The detection level is displayed by between dark and light color.
Note
Setting Threshold and Sensitivity is enabled after saving, and reflect to 
preview. 
SettingDescription
Threshold Adjust the threshold for Motion Detection.
Sensitivity  If you set sensitivity high, amplitude of motion detection bar 
gets jumpy.