Panasonic Digital AV Mixer Agmx70 Operating Instructions

							4141
≥With the page turn group (number 6008)
R2: [Rotate] (rotation) setting
R3: [Angle] setting
R4: [Turn] setting
R5: [Radius] setting
≥With the ripple group (number 6031)
R2: [Level] (amplitude) setting
R3: [Time] setting
R4: [Width] setting
The position of the ripple center can be changed using
[Shift] + XY.
≥With the spark group (number 6032)
R2: [Width] setting
R3: [Size] setting
R4: [Time] setting
≥With the melt group (numbers 6033 to 6034)
R2: [Level] setting
≥With the twist group (numbers 6009 to 6010)
R2: [Rotate] (rotation) setting
R3: [Turn] setting
R4: [Tilt] setting
3D
ModifyRotate
128Angle
32Turn
64Radius
3
0 - 255
0 - 2550 - 2550 - 7
3D
ModifyLevel
32Time
64Width
1
0 - 255
0 - 2550 - 5
3D
ModifyWidth
32Size
2Time
255
0 - 255
1 - 30 - 255
3D
ModifyLevel
128
0 - 255
3D
ModifyRotate
128Turn
128Tilt
128
0 - 255
0 - 2550 - 255
Effect-by-effect setting screens
R1 R2 R3 R4 R5
R1 R2 R3 R4 R5
R1 R2 R3 R4 R5
R1 R2 R3 R4 R5
R1 R2 R3 R4 R5 
						

							42
3D
ModifyEmpty
9000 Setup
9000 - 9019
Empty
Saved
Setup
Preview
CLR
All CLR
Effect-by-effect setting screens
[Key Learn] setting
This is used to set key learn.  It cannot be set for number
3001 to 3006, 3301 to 3305, 6001 to 6003 and 6006 to 6010
doors.  The key XYZ, key level and 3D modify settings are
stored in the memory for each key frame.
The key patterns are selected using the rotary 2 and 3
controls.  Selection is made from 9000 to 9019.
[Saved] is displayed for a pattern once set by the pattern
number, and [Empty] is displayed for a pattern which has
not yet been set.
Select [Setup], [Preview], [CLR] or [All CLR] using the rotary
4 control, and enter the selection using [Enter].
The operation of a set key is reproduced by selecting a
pattern with the [Saved] display and then selecting [Preview]
followed by [Enter].
When a pattern with the [Saved] display is selected and
either [CLR] or [All CLR] is selected followed by [Enter],
[OK?] appears.  By selecting [Enter] at this point, the
selected key learn pattern is cleared if [CLR] was selected
or all the key learn patterns are cleared if [All CLR] was
selected.  Clearing is canceled using [Shift] + [Enter].
With either [Empty] or [Saved] patterns, the editing mode is
established by selecting [Setup] followed by [Enter], and the
display is switched.  When a [Saved] pattern is to be set,
[OK?] appears: use [Enter] to set the pattern or [Shift] +
[Enter] to cancel the setting.
R1 R2 R3 R4 R5 
						

							43
With Sphere (#6001)
Effect-by-effect setting screens
Pos. X 128 Y 128
Z 196
Event ME Time Pattern INT
00E10:00F3013 Wht
Key
Learn
CLR KF
CopyK Frame
00K Level
255
Insert
Replace Basic
Paste
Exit9000
In the key learn editing mode, the key frame number is displayed in [K Frame].
Using the rotary 1 control, the editing items are selected and key frames are set.  Key frames 00 to 19 can be set, and they
are displayed during editing in the rotary 2 control display area.
The time settings for the key frames to date can be set by [ME Time].  This is useful for an additional [KeyFrame].  During
learning, ME is automatically selected for time.
Editing items that can be selected by the rotary 1 control
Insert: A key frame is inserted in the space of the next key frame.  Insert is executed using [Enter].
Replace: The current key frame is replaced.  Replace is executed using [Enter].
CLR KF: The current key frame is cleared.  Clear is executed using [Enter].
Copy: The current key frame is copied.  Copy is executed using [Enter].
Paste: The key frame in the copy buffer is pasted by overwriting.  Paste is executed using [Enter].  If the key frame has
not been copied, the execution menu cannot be selected.
Exit: Key learn is stored in the memory after exiting the editing mode.  Exit is executed using [Enter].
In the editing mode, it is possible to set the parameters using the rotary 2, 3, 4 and 5 controls, XYZ using the joystick XY and
rotary Z control, the aspect ratio using [Aspect], the key frames using [Shift] + rotary 2 control, and the key level using [Shift]
+ rotary 5 control.
To set another key pattern, first exit this screen, proceed with key pattern input again, and execute key learn.
Insert
Replace
CLR KF
Copy
Paste
ExitBasic
K Frame
00K Level
255Insert
Replace
CLR KF
Copy
Paste
ExitSphere
K Frame
00K Level
255
Rotate
128Time
0TransF
255
With basic patterns (#3001 to #3006) that can be
positioned and basic compressed patterns (#3301 to
#3304)
R2: [Rotate] rotation setting
R4: [Time] setting
R5: [TransF] (transformation) setting
XY Position
3D parameters are the same as with 3DModify.
R1 R2 R3 R4 R5 R1 R2 R3 R4 R5
R1 R2 R3 R4 R5 
						

							44
With flag (#6002)
Effect-by-effect setting screens
Insert
Replace
CLR KF
Copy
Paste
ExitFlag
K Frame
00K Level
255
Width
192Angle
64Time
48Amp
32
R2: [Width] (flag width) setting
R3: [Angle] setting
R4: [Time] (fluttering time) setting
R5: [Amp] (amplitude) setting
3D parameters are the same as with 3DModify.
With accordion (#6003)
Insert
Replace
CLR KF
Copy
Paste
Exit
Accordion
K Frame
00K Level
255
Width
192Angle
64Amp
32
R2: [Width] (accordion width) setting
R3: [Angle] setting
R5: [Amp] (amplitude) setting
3D parameters are the same as with 3DModify.
With the perspectives group (#6006 to #6007)
Insert
Replace
CLR KF
Copy
Paste
Exit
Perspective
K Frame
00K Level
255
Rotate
128Axis
0View
128Depth
64
R2: [Rotate] (rotation) setting
R3: [Axis] (rotary axis) setting
R4: [View] (viewer) setting
R5: [Depth] setting
3D parameters are the same as with 3DModify.  Key
learn is not possible for doors.With page turn (#6008)
Insert
Replace
CLR KF
Copy
Paste
Exit
Page Turn
K Frame
00K Level
255
Rotate
128Angle
32Turn
64Radius
3
R2: [Rotate] (rotation) setting
R3: [Angle] setting
R4: [Turn] setting
R5: [Radius] setting
3D parameters are the same as with 3DModify.
With twist group (#6009 to #6010)
Insert
Replace
CLR KF
Copy
Paste
ExitTwist
K Frame
00K Level
255
Rotate
128Turn
128Tilt
128
R2: [Rotate] (rotation) setting
R3: [Turn] setting
R4: [Tilt] setting
R1 R2 R3 R4 R5 R1 R2 R3 R4 R5
R1 R2 R3 R4 R5 R1 R2 R3 R4 R5
R1 R2 R3 R4 R5 
						

							45
Effect-by-effect setting screens

When a compression effect has been applied to images, some of the effects may be automatically canceled.
≥When applying 2D compression effects to channel A
Under the conditions below, the Still, Strobe and Multi Strobe for channel A are turned OFF when the Transition lever or
key size adjustment Z has been changed or the compression rate has been changed by the aspect ratio.
Conditions: When [DSK-Effects] is OFF and any of the Rev or Dual PinP patterns below has been selected
• 2DcompKey (2D + 3Dcomp included) + Rev
• 2DcompTrans + Rev
• 2Dcomp2Trans (+ Rev)
• 2Dslide1Trans (+ Rev)
• 2Dslide2Trans (+ Rev)
≥When applying 2D compression effects to channel B
Under the conditions below, the Still, Strobe and Multi Strobe for channel B are turned OFF when the Transition lever or
key size adjustment Z has been changed or the compression rate has been changed by the aspect ratio.
Conditions: When [DSK-Effects] is OFF and any of the Norm or Dual PinP patterns below has been selected
• 2DcompKey (2D + 3Dcomp included) + Rev
• 2DcompTrans
• 2Dcomp2Trans
• 2Dslide1Trans
• 2Dslide2Trans
The processing procedure differs depending on whether the 3D optional board (AG-VE70) has been installed or nor.  Details
are as follows.
≥When the 3D optional board (AG-VE70) is not installed
Pattern number selected Processing after cancel operation
1501 to 1533 (28 to 31, 36 to 42, 128 to 129) 2Dcomp
1541 to 1550 (32 to 35, 130 to 133, 141 to 142) 2chComp
1301 to 1333 (43 to 46, 51 to 54, 138 to 140) 2DSlide1 (only Multi Strobe is set OFF)
1341 to 1348 (47 to 50, 134 to 137) 2DSlide2 (only Multi Strobe is set OFF)
3301 to 3303, 3311 to 3313, 3501 to 3578 2Dcomp Key
3304, 3314, 3324, 3501 to 3378 Dual PinP
1401 to 1498 (143 to 182) 2Dcomp/MoveKey
3401 to 3478 2DcompMoveKey (OFF when Z is changed)
3601 to 3623 Bounce Key (OFF when Z is changed)
Pattern number selected Processing after cancel operation
1341 to 1348 (47 to 50, 134 to 137) 2DSlide2 (only Multi Strobe is set OFF)
1541 to 1550 (32 to 35, 130 to 133, 141 to 142) 2chComp
3304, 3314, 3324, 3501 to 3378 Dual PinP
4601 to 5614, 6031 to 6037 3D + 2Dcomp Key (OFF when Z is changed)
≥When the 3D optional board (AG-VE70) is installed 
						

							46
[DSK Source] settings
These are used to select the DSK [Key] and [Fill] signals.
Select the key signals using the rotary 2 control.  Either
[EXT] (external) or [Title] can be selected.
Select the key fill signals using the rotary 3 control.  [EXT]
(external) input, [Title] or [BodMat] (border matte) can be
selected.
Select the page number of the title memory using the rotary
4 control.  The total number of pages can be changed on
the [Setup] setting screen.
DSK
SourceKey
EXTFill
EXTPage
1-1Mode
Write
EXT
Title
EXT
Title
BodMat1-30/26
(NSTC/PAL)
- 1-8
Write
Preview
Set the operation using the rotary 5 control.  Either [Write] or [Preview] can be selected.
Set [Mode] to [Write], and write the KEY, Y, Pb and Pr external input signals into the memory using [Enter].
What is written is the whole frames of the images.  Sub-frames are ignored.  If the page concerned is used as a group, the
pages of the entire group will be cleared as well.  Since the saving that is initiated by [Write] supports only the [EXT] external
inputs, set [Key] and [Fill] to [EXT].
Set [Mode] to [Preview], and select [Enter] to initiate the preview display.  It is now possible to check the slides or movie
movements from On to Off.  The default setting is [Preview].
When [Title] has been selected for [Key] and [Fill] and preview is initiated, the title, star and heart keys are canceled and
changed to MIX (56).
The title page can be selected using the rotary 4 control.  The first number is for the page and the second number for the
sub-pages.
When part of a group has been selected, playback is initiated from the start of that part.
The playback type of the title concerned is displayed in the top section.  Preview for [Movie], [Crawl] and [Roll] is initiated by
[Shift] + [0].
R1 R2 R3 R4 R5
Pos. X 128 Y 128
Z 196
Event ME Time Pattern INT
00E10:00F3015 Wht
DSK Fade Still
DSK
Source
DSK
On/OffME Trig
OffSlide In
Off
Slide Out
OffSpeed
8
DSK
Effects OffLight
On
Crop
A
28
127
12
Fade To
BlackAudio
OnPhone
After Key
EXTFill
EXTPage
1-1Mode
Write
DSK
KeySlice
0Slope
0K Level
255
These settings are opened when the DSK/FADE button or DSK Preview is selected.  Both DSK and Fade settings can be
performed.
Select the [DSK Source], [DSK Key], [Crop], [DSK On/Off], [DSK Effects] or [Fade] item using the rotary 1 control.  When the
title memory is 0, the Key [Memory], Source [Memory], [Memory], [Mode] and [Slide] settings are canceled.
Still
Crawl
Roll
Movie
R1 R2 R3 R4 R5
DSK/Fade settings
6
A 
						

							47
DSK/Fade settings
[DSK Key] settings
These are used to set the DSK key signals (for external
applications).  Memory keys are used in their original form.
The [Slice] level can be set to any value from 0 to 255 using
the rotary 2 control.  The default setting is 0.
[Slope] can be set to any value from 0 to 15 using the rotary
3 control.  The default setting is 0.
The [K Level] (key level) can be set to any value from 0 to
255 using the rotary 5 control.  The default setting is 255.
[Crop] setting
This is used to set crop for DSK.
The top can be set to any value from 2 to 200 using the
rotary 2 control.  The default setting is 6.
The bottom can be set to any value from 2 to 200 using the
rotary 3 control.  The default setting is 2.
The left can be set to any value from 0 to 680 using the
rotary 4 control.
The right can be set to any value from 0 to 680 using the
rotary 5 control.
The default setting in each of these cases is 12.
If the top setting is changed, the bottom setting will change,
and vice versa, in such a way that the total setting will not
exceed 200.  Similarly, if the left setting is changed, the right
setting will change, and vice versa, in such a way that the
total setting will not exceed 680.  The left and right settings
can be changed in 1-step increments.
DSK
KeySlice
0Slope
0K Level
255
0 - 255
0 - 150 - 255
Crop
A
28
127
12
0 - 200
0 - 2000 - 6800 - 680
R1 R2 R3 R4 R5
R1 R2 R3 R4 R5
[DSK On/Off] setting
This is used to set the DSK on/off operations.  [Slide
IN/OUT] takes effect when [Title] has been selected for
[Key] and [Fill].
Whether the in or out operation is to be initiated during an
ME transition is set using the rotary 2 control.
Whether the sliding in operation is to be initiated in the
horizontal or vertical direction during DSK ON is set using
the rotary 3 control.
Whether the sliding out operation is to be initiated in the
horizontal or vertical direction during DSK OFF is set using
the rotary 4 control.
1: Slide toward the right
2: Slide toward the left
3: Slide toward the top
4: Slide toward the bottom
DSK
On/OffME Trig
OffSlide In
OffSlide Out
OffSpeed
8
On
Off
Off
1
2
3
4Off
1
2
3
42 - 64
The default setting in each of these cases is [Off].
The sliding speed is set using the rotary 5 control.  Any even number from 2 to 64 can be selected.  The default setting is 8.
When sliding has been selected, the DSKTime is changed to 0.  During sliding, the DSK buttons have no effect but become
operational again upon completion of the sliding operation.  This setting can also be changed at the PC.

Sliding in the vertical direction cannot be used when the data selected for the DSK source is other than DIVIDE1.  For details
on DIVIDE, refer to page 76.
R1 R2 R3 R4 R5
6
A 
						

							48
DSK/Fade settings
[Fade] settings
These are used to perform the fade settings.
The image to be faded is selected from [Black], [White] or
[Blue] using the rotary 2 control.  The default setting is
[Black].
[On] or [Off] is selected for [Audio] fading using the rotary 3
control.  The default setting is [On].
[After] or [Pre] is selected for [Phone] fading using the rotary
4 control.  At [After], the sound is heard with the fading
effect applied to the images; at [Pre], it is heard with no
fading effect applied to the images.  The default setting is
[After].
Fade To
BlackAudio
OnPhone
After
Black
White
Blue
On
OffAfter
Pre

Only one of three settings—namely, DSK memory, title key or star/heart key—can be selected.  The key selected last takes
precedence, and the previously selected key is canceled.
When the pattern is changed to MIX (56), the title key or heart/star key is to be canceled.  During title DSK, the heart/star key
cannot be used.
R1 R2 R3 R4 R5 
						

							49
[Audio Effects] settings
[PAN] setting
Set [On] or [Off] using the rotary 3 control.  The default
setting is [Off].
Select the input channel to be used using the rotary 4
control.  Select [L], [R] or [L+R].  The default setting is [L].
Set the output balance using the rotary 5 control.  Make the
selection from L7 to 0 to R7.  The default setting is 0.
PAN
1 OffIN Ch
LBalance
0
L7 - 0 - R7On
OffL
R
L+R
Pos. X 128 Y 128
Z 196
Event ME Time Pattern INT
00E10:00F3015 Wht
Audio Effects
EQ
MidM Level
0Freq
1.01KHzQ
0.5
Voice
Change OffPitch
UpLevel
5
Mute
Off AB Pan
OffIN Ch
LBalance
0
1EQ
OnLow
0High
0 1 - 8
Aux1
Aux2
[Audio Effects] is opened using Audio Effects or the ON button.  Audio effects can be set for each input.
Select the input from [1] (crosspoint 1), [2] (crosspoint 2), [3] (crosspoint 3), [4] (crosspoint 4), [5] (crosspoint 5), [6]
(crosspoint 6), [7] (crosspoint 7), [8] (crosspoint 8), [AUX1] or [AUX2] using the rotary 1 control.
Select the item from [PAN], [EQ] (equalizer), [EQ Mid] equalizer midrange, [Voice] (voice changer) or [Mute] using the rotary
2 control.R1 R2 R3 R4 R5
R1 R2 R3 R4 R5 
						

							50
[Audio Effects] settings
[EQ Mid] equalizer midrange setting
The [M Level] midrange level can be set in 2 dB intervals to
any value from –14 dB to 0 to +14 dB using the rotary 3
control.  The default setting is [0].
The midrange frequency can be set to any value from 100
Hz to 10.2 kHz using the rotary 4 control.  The default
setting is 1.01 kHz.
Select [0.5], [1], [2] or [5] for Q using the rotary 5 control.
The default setting is [0.5].
[Voice Change] (voice changer) setting
This is used to set the voice changer.
Set [On] or [Off] using the rotary 3 control.  The default
setting is [Off].
Set [Up] or [Down] for the [Pitch] using the rotary 4 control.
The default setting is [Up].
[Level] can be set to any value from [0] to [10] using the
rotary 5 control.  The default setting is [5].
1EQ
MIdM Level
0Freq
1.01KHzQ
0.5
–14 - +14100 Hz -
10.2 KHz0.5
1
2
5
1Voice
Change OffPitch
UpLevel
5
On
Off
Up
Down0 - 10
[Mute] setting
Set the mute level using the rotary 3 control.  [Off], [–12 dB],
[–20 dB] or [–60 dB] can be selected.  The default setting is
[Off].
Select the channel to be muted using the rotary 4 control.
[AB] (AB bus only), [ABAUX1] (AB bus and Aux1) or [All]
can be selected.  The default setting is [All].
Mute
–12dB AB
Off
–12dB
–20dB
–60dB
AB
ABAUXl
All
[EQ] equalizer setting
This is used to set the equalizers.
Set [On] or [Off] for all equalizers using the rotary 3 control.
The default setting is [On].
The [L Level] bass level can be set in 2 dB intervals to any
value from –14 dB to 0 to +14 dB using the rotary 5 control.
The default setting is [0].
The [H Level] treble level can be set in 2 dB intervals to any
value from –14 dB to 0 to +14 dB using the rotary 4 control.
The default setting is [0].
1EQ
OnL Level
0H Level
0
On
Off
–14 - +14–14 - +14
R1 R2 R3 R4 R5
R1 R2 R3 R4 R5
R1 R2 R3 R4 R5
R1 R2 R3 R4 R5