Panasonic Digital Camera Dmc Ts4 Owners Manual For Advanced Features

							- 191 -
Others
[Memory card error. 
This card cannot be used in this camera. 
Format this card?]
•
It is a format that cannot be used with this unit.> Insert a different card.
> Format the card again with the camera after saving necessary data on a PC etc.  (P60) 
Data will be deleted.
[Please turn camera off and then on again]/[System Error]
•
This message will be displayed when  the lens did not operate properly.
> Turn the camera off and on. If the message persists, contact the dealer or your nearest 
Service Center.
[Memory Card Error]/[Memory card parameter error]/[This memory card cannot be 
used]
>Use a card compatible with this unit.  (P24)–SD Memory Card (8 MB to 2 GB)–SDHC Memory Card (4 GB to 32 GB)–SDXC Memory Card (48 GB, 64 GB)
[Insert SD card again]/[Try another card]
•
An error has occurred accessing the card.
> Insert the card again.
> Insert a different card.
[Read Error/Write Error 
Please check the card]
•
It has failed to read or write data.
> Remove the card after turning the power off. Insert the card again, turn the power on, and 
try to read or write the data again.
•The card may be broken.
> Insert a different card.
[Motion recording was cancelled due to the limitation of the writing speed of the 
card]
•
Use a card with SD Speed Class with “Class 4”  or higher when recording motion pictures.•In the event that it stops even after using a “Class 4” card or higher, the data writing speed has 
deteriorated so it is recommended to make a backup and then format  (P60).
•Depending on the type of the card, Motion Picture Recording may stop in the middle. 
						

							Others
- 192 -
[Cannot record due to incompatible format(NTSC/PAL) data on this card.]
>Format the card after saving necessary data on a PC etc.  (P60)
> Insert a different card.
[A folder cannot be created]
•
A folder cannot be created because there are no remaining folder numbers that can be used.
> Format the card after saving necessary data on a PC etc.  (P60) If you execute [No.Reset] 
in the [Setup] menu after formatting, the folder number is reset to 100.  (P57)
[Picture is displayed for 16:9 TV]/[Picture is displayed for 4:3 TV]
•
Select [TV Aspect] in the [Setup] menu if you want to change the TV aspect. (P58)•This message also appears when the USB connection cable is connected to the camera only.
In this case, connect the other end of the USB connection cable to a PC or a printer.  (P165, 
169)
[Editing operation cannot proceed as information processing is ongoing.]
•
If a card inserted into the unit contains a group of pictures taken in [Time Lapse Shot] and one 
or more pictures from the group have been deleted or have had their file names changed in a 
PC or other device, the unit automatically retrieves new information and reconstitutes the 
group. When there are many image files, the currently retrieving information icon [ ] 
may be displayed for a significant period on the playback screen. During this period, it will not 
be possible to use delete or the playback menu.
If you turn off this unit while information is bei ng retrieved, only the still pictures for which data 
has been retrieved will be saved as the group.  When you switch on again, the information 
retrieval will restart from the same point.
[Recording failed.]
•
You may not record when the recording location is too dark/too bright, or if the subject does 
not have enough contrast when recording in 3D.
[This battery cannot be used]
•
Use a genuine Panasonic battery. If this message is displayed even when a genuine 
Panasonic battery is used, contact the dealer or your nearest Service Center.
•If the battery terminal is dirty, clean it and remove any objects.
[To prevent water leakage, ensure that the door is locked properly.]
•
Refer to P22  for details. 
						

							- 193 -
Others
Troubleshooting
First, try out the following procedures (P193–204).
•
The battery is exhausted. Charge the battery.•If you leave the camera on,  the battery will be exhausted.
> Turn the camera off frequently by using the [Economy] etc.  (P56)
•If you connect to a TV compatible with VIERA Link with an HDMI micro cable (optional) and 
turn off the power on the TV with the remote control for the TV, the power on this unit also turns 
off.
> If you are not using VIERA Link, set [VIERA Link] to [OFF].  (P59)
•Insert all the way until you hear a locking sound and it is locked by the lever while being careful 
about the direction the battery is inserted. (P21)
If the problem is not resolved, it may be improved by selecting [Reset]  (P57) on the 
[Setup] menu.
Battery and power source
The camera cannot be operated even when it is turned on.
The camera turns off immediately after it is turned on.
This unit is turned off automatically.
Side door does not close. 
						

							Others
- 194 -
•[GPS Setting] is set to [OFF]. (P115)•Radio waves from GPS satellites may not be received depending on the recording 
environment, such as indoors or close to a building.  (P114)
> It is recommended to use by holding the camera still for a while at an outdoor location clear 
to the sky, with the antenna pointed upward.
•[GPS Setting] is set to [ON].
> Set [GPS Setting] to [OFF] or [Airplane Mode] to [ON] when you turn the unit off onboard an 
airplane or inside a hospital etc.  (P131)
•It may take a few minutes the first time you use it or when it has not been used for a while.•Positioning is performed within 2 minutes normally, but since the position of the GPS satellites 
change, it may take longer depending on the location or environment of the recording.
•It will take longer for positioning in an environment where it is harder to receive the radio waves 
from the GPS satellites. (P114)
•Straight after the power is turned on, or when the GPS icon is not set to [ ], current location 
and location name information stored in the unit may differ significantly.
•It can be changed to a different candidate before  recording a picture when [ ] is displayed. 
(P119)
•When a landmark etc. does not exist nearby or no information is registered in the database of 
the unit, [---] is displayed.  (P117)
> You can enter location names etc. with  [Place-Name Edit] during the playback.  (P142)
About the GPS
Positioning is not possible.
GPS status indicator is lit while the power is turned off.
Positioning takes time.
Location name information is different from the place the picture was recorded 
in.
Location name information is not displayed. 
						

							- 195 -
Others
•Is there any memory remaining on the built-in memory or the card?> Delete the pictures which are not necessary to increase the available memory.  (P44)
•You may not be able to record for a short while after turning the power on when using a large 
capacity card.
•The picture can become whitish if there is dirt e.g. fingerprints on the lens.
> When it is dirty, lightly wipe the surface of the lens with soft and dry cloth.
•Is the inside of the lens fogged?
> There is condensation. Refer to “When inner side of the lens is fogged (condensation)” on 
P6  for what to do.
> Check that the exposure is correctly compensated.  (P70)
•Setting the [Min. Shtr Speed] to faster speed might make the picture darker.
> Set the [Min. Shtr Speed]  (P101) to slower speed.
> Set Auto Bracket  (P71) or [Burst]  (P103) of the [Rec] menu to [OFF].
•The focus range varies depending on the Recording Mode.
> Set to the proper mode for the distance to the subject.
•The subject is beyond the focus range of the camera.  (P33)•There is camera shake (jitter) or the subject is moving slightly.  (P29)
•Turn the power on again. If the operations are still not working normally, remove the power and 
consult the dealer or your nearest Service Center.
Recording
The picture cannot be recorded.
The recorded picture is whitish.
The recorded picture is too bright or dark.
Multiple pictures are taken at one time.
The subject is not focused properly.
The auto-focus and other operations are not working normally. 
						

							Others
- 196 -
>The shutter speed becomes slower when pictures are taken in dark places so hold the 
camera firmly with both hands to take the pictures.  (P29)
> When taking pictures at a slow shutter speed, use the Self-timer.  (P69)
•Is there any memory remaining on the built-in memory or the card?
•Is the ISO sensitivity high or the shutter speed slow?
(ISO sensitivity is set to [AUTO] when the camera is shipped. Therefore, when taking pictures 
indoors etc. noise will appear.)
> Decrease the ISO sensitivity.  (P94)
> Take pictures in bright places.
•Have you set [High Sens.] in Scene Mode, or [Burst] in [Rec] menu to [ ] or [ ]? If so, the 
resolution of the recorded picture decreases slightly because of high sensitivity processing, but 
this is not a malfunction.
•When recording under fluorescent or LED lighting fixture etc., increasing the shutter speed may 
introduce slight changes to brightness and color. These are a result of the characteristics of the 
light source and do not indicate a malfunction.
The recorded picture is blurred.
The Optical Image Stabilizer is not effective.
Taking pictures using Auto Bracket is not possible.
The recorded picture looks rough.
Noise appears on the picture.
The brightness or the hue of the recorded picture is different from the actual 
scene.
When recording pictures or half-pressing the shutter button, reddish stripes may 
appear on the LCD monitor. Alternatively, part or all of the LCD monitor may turn 
a reddish color.
•
This is a characteristic of CCDs, and it appears when the subject has a 
bright part. Some unevenness may occur in the surrounding areas, but 
this is not a malfunction.
It is recorded in motion pictures but is not recorded on still pictures.
•It is recommended that when you take pictures you take care not to 
expose the screen to sunlight or any other source of strong light. 
						

							- 197 -
Others
•Use a card with SD Speed Class with “Class 4” or higher when recording motion pictures.•Depending on the type of the card, recording may stop in the middle.> If Motion Picture Recording stops during use of a card of at least “Class 4” or if you use a 
card that has been formatted on a PC or other equipment, the data-writing speed is lower. 
In such cases, we recommend that you make a backup of the data and then format  (P60) 
the card in this unit.
•Set the AF area to the distinctive color of the subject if there is a part that is different from the 
surrounding color. (P99)
•If the camera is moved too slowly, the camera has assumed that camera motion was stopped 
and will end the still picture recording.
•If there is a great deal of shaking towards the recording direction while moving the camera, 
recording will end. > When recording with [Panorama Shot], move the camera by trying to trace a small circle 
parallel to the recording direction at a speed of about 8 seconds per revolution (estimated).
•It is possible that the subject may be warped slightly, or the borders get colored, depending on 
the zoom magnification, due to the characteri stics of the lens. Also, the peripherals of the 
image might look warped because the perspective is enhanced when the wide angle is used. 
This is not a malfunction.
•The inside of the lens may fog due to condensation depending on the environment this unit is 
used in, areas that undergo a significant change in temperature or in high humidity, etc. Refer 
to 
“When inner side of the lens is fogged (condensation)” on  P6 for directions.
Motion Picture Recording stops in the middle.
Subject cannot be locked.
(AF tracking not possible)
Recording by [Panorama Shot] is ended before finishing.
Lens
Recorded image may be warped, or nonexistent color is surrounding the 
subject.
The inner side of the lens is fogged. 
						

							Others
- 198 -
•This phenomenon appears when you press the shutter button halfway to set the aperture value 
and does not affect the recorded pictures.
•This phenomenon also appears when the brightness changes when the camera is zoomed or 
when the camera is moved. This is because of operation of the automatic aperture of the 
camera, and it is not a malfunction.
•The LCD monitor may flicker for a few seconds after the power is turned on. This is an 
operation to correct flicker caused by lighting such as fluorescent lights, LED lights, etc. and is 
not a malfunction.
•Is [LCD Mode] active? (P53)•Perform [LCD Display].  (P52)
•This is not a malfunction.
These pixels do not affect the recorded pictures.
•In dark places, noise may appear to maintain the brightness of the LCD monitor. This does not 
affect the pictures you are recording.
•Is the flash setting set to [ Œ]?
> Change the flash setting.  (P65)
•The flash cannot be used in the following cases:–When using Auto Bracket  (P71)–In Miniature Effect Mode (P77)–[Scenery]/[Panorama Shot]/[Night Scenery]/[Handheld Night Shot]/[Sunset]/[Glass Through] 
in Scene Mode (P78)
–In 3D Photo Mode  (P85)–When recording in [Burst] (except for [ ])  (P103)
•The flash is activated twice when Red-Eye Reduction  (P65) has been set.•Has [Burst]  (P103) in the [Rec] menu been set to [ ]?
LCD monitor
The LCD monitor becomes darker or brighter for a moment.
The LCD monitor flickers indoors.
The LCD monitor is too bright or dark.
Black, red, blue and green dots appear on the LCD monitor.
Noise appears on the LCD monitor.
Flash
The flash is not activated.
Flash is activated several times. 
						

							- 199 -
Others
•[Rotate Disp.] (P59) is set to [ ] or [ ].
•Is there a picture on the built-in memory or the card?
> The pictures on the built-in memory appear when a card is not inserted. The picture data on 
the card appears when a card is inserted.
•Is this a folder or picture which was processed in the PC? If it is, it cannot be played back by 
this unit.
> It is recommended to use the “PHOTOfunSTUDIO” software in the CD-ROM (supplied) to 
write pictures from PC to card.
•Has [Filtering Play] been set for playback?
> Change to [Normal Play].  (P132)
•Is this a non-standard picture, a picture whic h has been edited using a PC or a picture which 
was taken by another make of digital camera?
•Did you remove the battery immediately after pict ure-taking or did you take the picture using a 
battery with a low remaining charge? > Format the data to delete the pictures mentioned above.  (P60) 
(Other pictures will be deleted as well and it will not be possible to restore them. Therefore, 
check well before formatting.)
•Is the clock in the camera set properly?  (P27)•When pictures edited using a PC or pictures taken by other equipment are searched, they may 
be displayed on dates differing from the actual dates on which the pictures were taken.
Playback
The picture being played back is rotated and displayed in an unexpected 
direction.
The picture is not played back.
The recorded pictures are not displayed.
The folder number and the file number are displayed as [—] and the screen turns 
black.
With a Calendar Search, pictures are displayed on dates differing from the actual 
dates on which the pictures were taken. 
						

							Others
- 200 -
•When Digital Red-Eye Correction ([ ], [ ]) is in operation, if you take a picture of 
subject with red color surrounded by a skin tone color, that red part may be corrected to black 
by the Digital Red-Eye Correction function.> It is recommended to take the picture with the Flash Mode set to [ ‡], [‰] or [ Œ], or 
[Red-Eye Removal] on the [Rec] menu set to [OFF].  (P109)
•Is it a picture that has been recorded with other equipment? In such cases, these pictures may 
be displayed with a deteriorated picture quality.
•This unit automatically adjusts the aperture during Motion Picture Recording. At such times, the 
sound may break up. This is not a malfunction.
•Motion pictures recorded in [AVCHD] or [MP4] may be played back with poor picture or sound 
quality or playback may not be possible even when played back with equipment compatible 
with these formats. Also, the recording information may not be displayed properly.
White round spots like soap bubbles appear on the recorded picture.
•
If you take a picture with the flash in a dark place or indoors, white 
round spots may appear on the picture caused by the flash reflecting of 
particles of dust in the air. This is not a malfunction.
A characteristic of this is that the number of round spots and their 
position differ in every picture.
Red part of the recorded image has changed color to black.
[Thumbnail is displayed] appears on the screen.
The sound of the recorded motion pictures sometimes breaks up.
Motion pictures recorded with this model can not be played back on other 
equipment.