Panasonic Digital Catv Terminal Tzpcd2000 Operating Instructions

							11
Digital CATV Terminal connection to TV and VCR
Installation
Follow this diagram when connecting the Digital CATV Terminal to a TV and VCR.
Procedure
l Connect the CABLE OUT jack of the Digital CATV Terminal to the ANT IN jack of the VCR, and connect the ANT
OUT jack of the VCR to the ANT IN jack of the TV using 75 W shielded cable.
Connecting a non-cable ready TV
VHF Matching
TransformerJumper Cable
TV Set VHF Antenna Terminals
Rear of Non Cable-Ready TV TV Set UHF Antenna
Terminals
Note:
l Additional equipment and cables shown are not supplied with this set.
VCR or S-VCRTV 
						

							12
Installation
Digital CATV Terminal connection to component with Digital Audio Input jack
Follow this diagram to connect the Digital CATV Terminal to a component with a Digital Audio Input jack.
Procedure
1
Connect the Digital Audio Cable from the Digital Audio Out jack on the Digital CATV Terminal to the Digital Audio
Input jack on the component with the Digital Audio Input jack.
2Connect the TV or other component while referring to page 10.
Note:
l If using a Dolby Digital AC-3 decoder, you can enjoy Dolby Digital (AC-3) 5.1 channel surround sound.
l Additional equipment and cables shown are not supplied with this set.
Connect AC Power Cord
Procedure
lConnect the AC power cord to the AC power input at the rear of the Digital CATV Terminal, and plug the AC power
cord into a grounded outlet.
AC Power Cord
AC Power CordTV
Dolby Digital
AC-3 decoder
or6-Channel Amplifier
& Speakers 
						

							13
Power ON/OFF
Installation
Push the POWER button on this unit to turn the set on
POWER-ON
Press POWER once more to turn off.
Power Indicator: Green
Power Indicator: Indicator not illuminated
( Please understand the Digital CATV Terminal is not updated
when you plug off from AC outlet.)

1   Press the Remote Control CBL mode button
2   Press the POWER button.
Changing the TV input source (Panasonic TV models)
1   Press the TV mode button.
2   Press the POWER button to turn on the power for the TV.
3   Press the TV/VCR button to select the picture from the Digital
 CATV Terminal. If the connection is via the CABLE OUT jack as
 shown on page 11, use the CH UP/DOWN button on the TV to
 set the channel to the VCR output channel (channel 3 or 4).
Note:
l If using a non-Panasonic brand TV, make the selection directly
at the TV itself, or use the TV’s remote control to make the
setting as described on page 17.
l Some Panasonic brand TVs may have different remote control
codes,so that these TVs cannot be operated as described
above even though they are Panasonic-brand TVs. In such
cases, make the selection directly at the TV itself, or use the
TV’s remote control to make the setting as described on page
17.
l The default remote control settings do not allow TV and VCR
CH UP/DOWN settings to be made.You first need to clear the
channel lock as described on page 20. Procedure
Power Indicator
21
2
31 
						

							14
Remote Control
CBL, TV, VCR, AUX
Press to select remote operation.
POWER
Press to turn ON and OFF.
Press to move through interactive
screen choices.
SELECT
Press to choose interactive screen
item.
Page
Press to display Next/Previous
screen.
A, B, C
On-Screen decision buttons
CH
Press to select channel Up/Down
Mute
Press to turn sound off.
Last
Press to return to last channel
viewed.
Menu
Press to display Settings menu.
Info
Press to display channel information.
Exit
Press to hide interactive screen.
Fav
Press to view favorite channels.
VOL
Press to adjust volume.
Guide
Press to display interactive
program guide.
0-9
Press to enter channel and
personal identification
numbers(PIN). 
						

							15
Remote Control
Remote Control Function Key Chart
ALL COMPONENTS
ALL COMPONENTS
CBL
CBL
TV
VCR
CBL
TV
VCR
AUX
CBL, TV
CBL
CBL, TV
CBL CBL CBL
CBL, TV, VCR
CBL, TV, VCR
AUX
CBL, TV, VCR
CBL, TVTurn components On and OFF
Channel information
On screen display
Program
Settings menu
ACTION
Menu
Program mode
Exit Menus
View favorite channels
Up,Down,Left and Right navigation
Select
Display Next/Previous screen
On-Screen decision buttons
Volume up/down
Channel up/down
Skip forward/rewind
Mute audio
The description of functions for each of the components in the table above apply when the factory
default code settings are in place. The factory default code settings are as follows:
TV:Panasonic brand TV (code: 0250)
VCR:Panasonic-brand VCR (code: 1062)
AUX:Panasonic-brand CD Player (code: 0303)
KeyComponent Function
Component mode selection for
remote control
Interactive program guide
Return to last channel viewed 
						

							16
Remote Control
Remote Control Function Key Chart
CBL, TV, VCRSelect channel
Select code
The description of functions for each of the components in the table above apply when the factory
default code settings are in place. The factory default code settings are as follows:
TV:Panasonic brand TV (code: 0250)
VCR:Panasonic-brand VCR (code: 1062)
AUX:Panasonic-brand CD Player (code: 0303)VCR
AUX
CBL
TV
VCR
AUX
CBL
TV
VCR
AUX
CBL
TV
VCR
AUX
CBL
TV
VCR
CBL
TV
VCR
AUX
CBL
TV
VCR
AUX
CBL
TV
VCR
AUX
ALL COMPONENTSChannel enter
Disc
VOD rewind
Punch to VCR
Rewind
Fast search rev
VOD play
Punch to VCR
Play
Play
VOD fast fwd
Punch to VCR
Fast forward
Fast search fwd
VOD record
Punch to VCR
record
VOD stop
Punch to VCR
Stop
Stop
VOD pause
Punch to VCR
Pause
Pause
BYPASS
TV/VIDEO
TV/VCR
SIDE A-B
SETUP
Key Component Function 
						

							17
Programming the Remote Control
The Universal Remote Control can be programmed to operate many manufacturers’components using the
component function buttons for TV, VCR, or AUX. Follow the procedures for programming your Remote Control
with and without codes for the component. Determine the manufacturer of the component and look in the table for
the code.
Use the following procedure to program the TV remote control code. At the time of
shipment from the factory, this is set to Panasonic-brand TVs (code:0250).
Use the following procedure to program the TV remote control code.
1.Select the Setup Code for your TV by referring to the tables on pages 21 to 24. If you
cannot find the right Setup Code, refer to “Programming Without Code” on page 18.
2.Press the TV button, and then press the Setup button and hold for 3 seconds (until
the visible LED blinks twice).
3.Use the numeric buttons on the remote control to enter a 4-digit Setup Code. When
programming is complete, the LED on the remote control will flash twice.
n Programming for TV operation
n Programming for VCR operation
n Programming for AUX (other component) operation
You can use the remote control for the Digital CATV Terminal to operate your VCR,DVD
player. However, a VCR Commander Module (not included) is requred in order to
program your VCR for recording. If you are not using a VCR Commander Module, you
will need to make the programming operations directly at the VCR. For details, refer to
the User’s Guide which is supplied with the VCR Commander package. At the time of
shipment from the factory, the code is set to Panasonic-brand VCRs (code: 1062).
Use the following procedure to program the VCR or DVD player remote control code.
1.Select the Setup Code for your VCR by referring to the tables on pages 21 to 24. If you
cannot find the right Setup Code, refer to “Programming Without Code” on page 18.
2.Press the VCR button, and then press the Setup button and hold for 3 seconds (until
the visible LED blinks twice).
3.Use the numeric buttons on the remote control to enter a 4-digit Setup Code. When
programming is complete, the LED on the remote control will flash twice.
You can use the remote control for the Digital CATV Terminal to operate a CD player,
DVD player, Audio Amplifier, Miscellaneous Audio component, Audio Amplifiers and
Tuners, Home Automation equipment or Cable Converter. At the time of shipment from
the factory, the code is set to Panasonic-brand CD player (code: 0303).
Use the following procedure to program the desired component.
1.Select the Setup Code for the desired component by referring to the tables on pages
21 to 24. If you cannot find the right Setup Code, refer to “Programming Without
Code” on page 18.
2.Press the AUX button, and then press the Setup button and hold for 3 seconds (until
the visible LED blinks twice).
3.Use the numeric buttons on the remote control to enter a 4-digit Setup Code. When
programming is complete, the LED on the remote control will flash twice.
If the component does not operate with the remote control, repeat the procedure using
another code. (Some brands have multiple codes.)
If you enter an incorrect Code, or if no button is pressed for 10 seconds or
more, the program will be canceled.
Unsuccessful Code
AUX button
VCR button
LED
TV button
Setup button
Numeric buttons 
						

							18
Programming the Remote Control
n Programming Without Code
If you cannot find the right Code, you can call up all Codes one after the other to
search for a Code.
1.Turn on the power for the Component to be programmed.
2.Press the mode button (TV, VCR or AUX) for the component to be programmed,
and then press the Setup button and hold for 3 seconds (until the visible LED blinks
twice).
3.Use the numeric buttons on the remote control to enter “991”. After this number is
entered, the LED on the remote control will flash twice.
4.Press the POWER button. (A remote control signal will be transmitted.)
5.If the component turns off, go to step 6. If the component remains on,  press the
mode button (TV, VCR or AUX), and then repeat step 4. (Repeat this step until the
right Code is found.)
6.Press the Setup button to register the Code. When programming is complete, the
LED on the remote control will flash twice.
n Identifying programmed Codes
If you would like to know what Code has been programmed, you can find out by
observing the flashing pattern of the remote control LED.
1.Press the mode button (TV, VCR or AUX) for the component that you would like to
find out the Code for, and then press the Setup button and hold for 3 seconds (until
the visible LED blinks twice).
2.Use the numeric buttons on the remote control to enter “990”. After this number is
entered, the LED on the remote control will flash twice.
3.When a “1” is then entered using the numeric buttons, the remote control LED will
flash. The number of times it flashes corresponds to the first digit of the Code. For
example, if the LED flashes five times, the first digit of the Code is 5.
4.When a “2” is then entered using the numeric buttons, the remote control LED will
flash. The number of times it flashes corresponds to the second digit of the Code.
5.When a “3” is then entered using the numeric buttons, the remote control LED will
flash. The number of times it flashes corresponds to the third digit of the Code.
6.When a “4” is then entered using the numeric buttons, the remote control LED will
flash. The number of times it flashes corresponds to the fourth digit of the Code.
7.Write the code numbers for your components in the space provided below. This will
serve as a reference when you need to program your remote control. AUX button POWER button
VCR button
LED
TV button
Setup button
Numeric buttons
TV
VCR
AUX
Name of component
TV
VCR  , DVD player ()
()
() 
						

							19
Programming the Remote Control
n Programming for volume control
The volume adjustment function can be locked so that regardless of whether CBL, TV
or VCR mode is active, the volume is adjusted for only one of the modes. (Refer to
the
table below.)
The default setting is TV. When the setting is AUX mode, you can adjust the volume
for the AUX component at all times, even if some other mode is currently active.
Setting method
1.Press the Setup button and hold for 3 seconds (until the visible LED blinks twice).
2.Use the numeric buttons on the remote control to enter “993”. After this number is
entered, the LED on the remote control will flash twice.
3.Press the button for the mode that you would like to lock the volume adjustment for.
When the setting is complete, the LED on the remote control will flash twice.
Canceling the setting
1.Press the Setup button and hold for 3 seconds (until the visible LED blinks twice).
2.Use the numeric buttons on the remote control to enter “993”. After this number is
entered, the LED on the remote control will flash twice.
3.Press the VOL + button. When the setting is canceled, the LED on the remote
control will flash four times.
Note:
lIn the case of Mode Reassignment, the operation will be as shown in the table
below. See below for details on Mode Reassignment.
n Mode Reassignment
You can assign the Code for setting a certain mode (TV, VCR or AUX) to use as the
Code for setting some other mode.
(Example) Assigning the button setting Code for TV mode to the button for VCR mode
1.Press the Setup button and hold for 3 seconds (until the visible LED blinks twice).
2.Use the numeric buttons on the remote control to enter “992”. After this number is
entered, the LED on the remote control will flash twice.
3.Press the TV button.
4.Press the VCR button. When the setting is complete, the LED on the remote control
will flash twice. Then you can use second TV (which has other Remote Code)
instead of VCR.
Note:
lThe Code for CBL mode cannot be assigned to any other mode. Furthermore, no
other Code can be assigned to CBL mode.
Volume
Locked to:
TV
VCR
CBL
AUXTV
TV TV TVVCR
VCR VCR VCR AUXAUX AUX
AUX
AUX AUX AUX AUX CBL CBL CBLCBL Physical Mode Keys
Volume
Locked to:
TV
VCR
CBL
AUXTV
TV TV2 TVVCR
TV2 TV2 TV2 AUXAUX AUX
AUX
AUX AUX TV2 AUX CBL TV2 CBLCBL Physical Mode Keys
TV2
Mode Reassigned to: VCR button AUX button
LED
TV button
Setup button
Numeric buttonsCBL button
VOL + button 
						

							20
n Changing button functions
The functions of the remote control buttons can be assigned to other buttons.
Setting method
(Example) Assigning the function of the POWER button in TV mode to the Exit button
in VCR mode
1.Press the Setup button and hold for 3 seconds (until the visible LED blinks twice).
2.Use the numeric buttons on the remote control to enter “994”. After this number is
entered, the LED on the remote control will flash twice.
3.Press the TV mode button, and then press the POWER button.
4.Press the VCR button, and then press the Exit button. When programming is com-
plete, the LED on the remote control will flash twice.
Canceling the setting
1.Press the Setup button and hold for 3 seconds (until the visible LED blinks twice).
2.Use the numeric buttons on the remote control to enter “994”. After this number is
entered, the LED on the remote control will flash twice.
3.Press the Mode button twice. When programming is complete, the LED on the
remote control will flash twice.
n Channel lock
The Digital CATV Terminal lets you lock the channel selection (0~9 buttons, CH Up/
Down buttons, Last button) functions. The following procedure can be used to set
whether channel selection is locked or not.
Clearing the lock
1.Press the Setup button and hold for 3 seconds (until the visible LED blinks twice).
2.Use the numeric buttons on the remote control to enter “973”. After this number is
entered, the LED on the remote control will flash twice.
3.Press the CH - button. When programming is complete, the LED on the remote
control will flash twice.
Setting the lock
1.Press the Setup button and hold for 3 seconds (until the visible LED blinks twice).
2.Use the numeric buttons on the remote control to enter “973”. After this number is
entered, the LED on the remote control will flash twice.
3.Press the CH + button. When programming is complete, the LED on the remote
control will flash twice.
n Reset
You can reset any remote control settings which have been changed.
The settings can be reset in either of two ways.
Operation setting reset
This resets all remote control settings to their factory default values, except for Codes
set in TV, VCR and AUX modes.
1.Press the Setup button and hold for 3 seconds (until the visible LED blinks twice).
2.Use the numeric buttons on the remote control to enter “980”. When resetting is
complete, the LED on the remote control will flash four times.
Factory default reset
This resets all remote control settings to the factory defaults.
1.Press the Setup button and hold for 3 seconds (until the visible LED blinks twice).
2.Use the numeric buttons on the remote control to enter “977”. When resetting is
complete, the LED on the remote control will flash four times.
Programming the Remote Control
AUX button POWER button
VCR button
LED
TV button
CH +- buttonNumeric buttonsSetup button
Exit
button