Panasonic Digital Imaging Systems Dp 1810p Copier Operating Instructions

41
3. Operation

Operation Procedure
ADF/i-ADF
Face-Up
1
Place the
Original
34
Inappropriate Originals
CPaper with a smooth surface such as glossy
and coated papers
CTransparencies
COriginals with a lead edge that is “creased”,
“folded”, “punched” or “glued”
Accessories
CPaste-ups
CPressure sensitive or carbon backed papers
CPaper with excessive curl
CStapled originals
CFreshly printed copies from a laser printer
NOTECTo copy these kinds of originals, use the Platen Glass instead.
(2)
For Duplex Copy
(If...

42

 

 


550-Sheet Paper Tray
Problem Solving
1
Pull the Paper Tray out.
2
Place the paper with the copying
surface facing upward.
Special papers, like glossy paper, mailing
labels and transparencies cannot be used
in the paper tray.
Use the Sheet Bypass for special paper.
3
Make sure paper is not loaded
above the overfill indicator located
in the Paper Tray.
Adding Paper (
J JJ J
J)
ATTENTIONCDo not use paper with folds or wrinkles.
Refer to page 35 for details on adjusting the paper tray size....

43
Adding the Toner and Replacing Toner Waste Container (
? ?? ?
?)
1
Open the Front Cover.
2
Remove the Toner Waste Container by
slowly pulling it towards the left as
illustrated.
3
Seal the container with the enclosed
cap and dispose of it properly.
4
#Turn the empty Toner Bottle
counter-clockwise until it stops. The
Arrow mark (Unlocked symbol    )
visible on the end of the Toner
Bottle is aligned with the Arrow
mark on the machine.
Note: To prevent toner spill, ensure
that the key is facing upwards...

44
5
#Shake the new Toner Bottle four
or five times to loosen the
contents.
$Remove the cap from the Toner
Bottle.
6
#Align the Key of the bottle, also
represented by the Arrow mark
(Unlocked symbol    ) visible on
the end of the Toner Bottle with
the Arrow mark on the machine.
Note: To prevent toner spill,
ensure that the key is facing
upwards before installing the
bottle.
$Inser t the bottle as far as it will
go, then turn it clockwise (160°,
approx. 1/2 turn) until it locks
(Locked symbol ).
Note: If...

45
NOTECMake sure that the misfeed indicator goes off after removing the misfed
paper.
CThe misfeed indicator will not go off if the paper is still jammed in the copier.
Check again and remove all misfed paper.
Paper Misfeed Locations
A: ADF (see page 51), i-ADF(see page 50)
(J70, J71)
B: Copier (Paper Exit, Paper Entry/Transport,
ADU) areas (see page 46-48) (J51 - J59,
J80)
C: Paper Feed Module (see page 49)
(J00 - J50)
IMisfeed Indicator
Removing a Misfed PaperProblem Solving

 

 


Paper Misfeed...

46
ATTENTION
Removing a Misfed Paper
CMake sure that the misfeed indicator goes off after removing all misfed paper.
1
Remove the misfed paper. 
Paper Exit Area
CMake sure that the misfeed indicator
goes off after removing all misfed
paper.
Problem Solving
For DP-1810P
For DP-2010E 

47
Problem Solving
1
2
3
Open the Right Cover.
Remove the misfed paper.
If copy paper is fed far into the copier:
#Turn the right paper clearing knob.
$Remove the misfed paper.

Paper Entry/Transport Area
CMake sure that the misfeed indicator
goes off after removing all misfed
paper.
ATTENTION
4
#Open the Heat Roller Cover.
$Remove the misfed paper.
%Close the Right Cover.
Caution: This fuser area may be
hot.Caution
heated
surface
CMake sure that the misfeed indicator goes off after removing all misfed...

48
Problem Solving
1
2
Open the Right Cover.
Remove the misfed paper. 

ADU Area (For DP-2010E only)
CMake sure that the misfeed indicator
goes off after removing all misfed
paper.
Removing a Misfed Paper
3
If copy paper is fed far into the copier;
#Turn the right paper clearing knob.
4
Close the Right Cover.
$Remove the misfed paper. 

49
Problem Solving
1
2
#Pull the paper tray out.
$Remove the misfed paper.
%Return the Paper Tray to the original
position.
#Open the Feed Cover.
$Remove the misfed paper.
%Close the Feed Cover.

Paper Feed Module
CMake sure that the misfeed indicator
goes off after removing all misfed
paper.
CMake sure that the misfeed indicator goes off after removing all misfed
paper.
ATTENTION
For DP-1810P
For DP-2010E
I 

50
ATTENTION
Removing a Misfed Paper
CPush the tab on the center of the Entry Cover to close it.
CTo prevent original(s) damage, please make sure to open the ADF Cover before
removing misfed original(s).

i-ADF (For DP-2010E only)
CMake sure that the misfeed indicator
goes off after removing all misfed
paper.
Problem Solving
1
2
#Open the Entry Cover.
$Remove the misfed paper.
%Close the Entry Cover.
#Open the ADF Cover.
$Remove the misfed paper.
%Close the ADF Cover.
&Open and close the Entry Cover to...