Panasonic Digital Imaging Systems Dp 1810p Copier Operating Instructions

							21
NOTE
4
Number of
Copies
5
Press
START
CTo reset each selection, press the RESET key.
CLedger and Legal copy sizes cannot be selected.
∗The book format and page order can be set in function mode. (See page 30)
CBook \ 2 Copy function is only available for DP-2010E. Platen
Ledger size original
LetterLedger
(3)
COPY SIZE
(Reduction/
Enlargement Only
*)
Book 
\ \\ \
\ 2 Copy (For DP-2010E)

Book 
\ \\ \
\ 2 Copy
From book originals to 2-Sided copies.
Ledger size originals only.
Facing (Book Format)
*Flipping (Book Format)*
1
Place the
Original on
the Platen
2
Press 2-Sided/
1-Sided Copy key
(circulation) to select
Book \ 2
Creative Features
Making Copies
Book Mark
Center book by
length and width
according to
center marks. 
						

							22
NOTE
Creative Features
Job Memory

 

 


Two Copy Jobs Can Be Programmed in Memory (M1, M2) for recall at a
later time.
To Store a Job in Memory
#Set up the copy job to be stored in memory,
by first selecting each function you wish the
copier to perform.
$Press the MEMORY IN (F2) key.
%Press the M1 (F3) or M2 (F4) key.
To Recall a Job Stored in Memory
&Place the Original
(Press the M1 (F3) or M2 (F4) key.
The stored contents will be displayed.
)Press START
CStored job(s) will not be deleted even if the power switch is turned Off.
CWhen storing a new job into programmed memory, the previously stored job will be
overwritten.
JOB MEMORY
PRESS M1,M2 TO STORE.
RECALL JOB MEMORY
LOADING... 
						

							23
Creative Features
Sort Copy
1
1
1
1
11
NOTECWhen the memory becomes full during original scanning, the message
“OUT OF MEMORY” “CONTINUE? 1: YES 2: NO” will be displayed in the
message display. If this occurs, follow the instructions in the message
display.
For additional memory consult your authorized servicing dealer.
CTo reset all job settings, press the RESET key.

Sort Copy
The sort copy has 2 available electronic sorting functions as follows:
Note: Before using the sort copy, select the desired sorting mode by setting its function first
           (See page 29).
1
ADF/i-ADF: Place the
Originals
Platen: Place the
  First Original
2
Select the
SORT Mode
(3)
COPY SIZE
(Reduction/
Enlargement
Only)
4
Number of
Copies
5
Press
START
6
ANOTHER ORIGINAL?
1:YES 2:NO
Press “1” key.
7
Place next Original
8
Press START
9
Repeat steps 6 and 7
until all originals are
scanned and stored
into the copier’s memory.
10
ANOTHER ORIGINAL?
1:YES 2:NO
Press “2” key. Sort Sort-Rotate
Multiple copies
sorted
automatically.Multiple copies sorted
automatically and
Stacked in alternate
direction.
(Up to Letter size)
From Platen Glass only:Platen Glass ADF/i-ADF
Making Copies 
						

							24
NOTE
INTERRUPT (F1) Key ENERGY-SAVER Key

These modes can save power while the copier is not
in use.
Energy Saver Mode
#To enter this mode
Press the ENERGY-SAVER key or the copier will
automatically enter the ENERGY-SAVER Mode after
15 minutes
* from the last copy. The indicator will flash.
$To cancel this mode and make copies
Press the ENERGY-SAVER key again.
Sleep Mode
#Automatically enters the Sleep Mode after 30
minutes from the last copy. The copier power will
drop and the indicator will light.
$To make copies, press the ENERGY-SAVER key.
Interrupt Mode
CThis mode can interrupt other copy jobs while
making copies.
#Press the INTERRUPT (F1) key, the indicator will
light.
$Make another copy job using the platen glass.
%Press the INTERRUPT (F1) key again to continue
the original job.
Note: The ADF can not be used with interrupt.
 (Use only the Platen)
∗Energy saver time (15 minutes) and Sleep time (30 minutes) can be changed by the
key operator. (See page 31)
Other Features
Modes Power Consumption Warm Up Time
Normal Operation
Energy Saver Mode
Sleep ModeApproximately 92 Wh
Approximately 40 Wh
Approximately 1.5 WhN/A
30 sec. recovery
30 sec. recovery
ENERGY SAVER
INTERRUPT
Energy Saver/Interrupt Mode 
						

							25
NOTECAn incorrect exposure may occur when there is a black line at the edge of
the original or an image which the copier interprets as a black pattern in the
Skyshot mode.
CAn incorrect position detection of the original may occur when a strong light
shines onto the glass during Skyshot mode.
Other Features
Skyshot Mode

 

 


Skyshot allows copying a manuscript without generating dark borders
even if the platen cover or ADF/i-ADF is opened.
Skyshot mode eliminates dark borders around the originals, and is especially convenient for
copying small-sized originals like bank checks or documents with unusual shapes (round, oval,
etc.). These documents can be reproduced without generating any unnecessary black areas
simply by making a copy with the cover open.
Two types of Skyshot modes can be selected;
Digital Skyshot Mode : The scanning area (size) is not pre-determined.
Manual Skyshot Mode : The scanning area (size) is pre-registered into memory (M1 and M2) in
advance. (See page 30)

 

 


Digital Skyshot Mode
1
Place the Original on
the platen (Opening the
Platen Cover/ADF)
Note: The default setting of Digital Skyshot Mode is “NORMAL”. In this setting, the unit scans once.
If there are black areas around the borders in the copies, set the Digital Skyshot Mode to
“QUALITY” to soften the dark borders.  In this setting, the unit scans twice.
#Press the FUNCTION key.
$Press the 2 key to select COPIER SETTINGS.
%Press the SET key.
&Press 6 and SET key to select DIGITAL
SKYSHOT.
(
Press 1-3 key to select the Digital Skyshot Mode.
1: OFF NONE
2: NORMAL Default setting (usually select this
mode).
3: QUALITY For better definition, select the
Quality mode.
)Press the SET key.
*Press the RESET key.
FUNCTION MODE  (1-2)
ENTER NO. OR ∨ ∧
2:COPIER SETTINGS
PRESS SET TO SELECT
COPIER PARAM. (00-14)
ENTER NO. OR ∨ ∧
06 DIGITAL SKYSHOT
 2:NORMAL
3
Press
START Key
2
Number of
Copies
Making Copies 
						

							26
NOTE
1
Place the
Original
23
Number of
Copies
4
Press
START Select the Custom
Size (M1 or M2) Upper-
left
corner Platen
Skyshot Mode

 

 


Manual Skyshot Mode
When using this function, the custom size should be registered into memory (M1, M2) in
advance. (See page 32)
Other Features
2
∗The default size for M1 is: 70(X) × 160(Y) mm, and M2 is: 95(X) × 220(Y) mm
CWhen changing the M1 or M2 size, consult with the key operator.
CWhen using the Manual Skyshot mode, M1 and M2 are turned ON and other
job memory cannot be used.
CPress the RESET key to cancel all job settings.
FUNCTION MODE  (1-2)
ENTER NO. OR ∨ ∧
2:COPIER SETTINGS
PRESS SET TO SELECT
COPIER PARAM. (00-14)
ENTER NO. OR ∨ ∧
07 MANUAL SKYSHOT
 2:M1 ON
#Press the FUNCTION key.
$Press the 2 key to select COPIER SETTINGS.
%Press the SET key.
&Press 7 and SET key to select MANUAL SKYSHOT.
(
Press 2 or 3 key to select the Custom Size.
1: OFF NONE
2: M1 ON M1 size is ON*
3: M2 ON M2 size is ON*
4: M1, M2 ON Both sizes are ON
)Press the SET key.
*Press the RESET key. 
						

							27
Next
Selections2-ORIGINAL
H HH H
H COPYMargin SORTOther
Functions
Zoom Copy
2 in 1 Copy
2 Page CopySort-Rotate
Manual Skyshot
Job Memory Retrieval
Job Memory Storing
Remarks
First
Selections
Sort Book
Edge
Margin
Non-Sort
Combined Function Table
OAAOAA AOOOOOOAAO
OAAAAAAOOOOOOAAO
O OOOOOOAOOOOOAAO
O OOOOOO OAOOOOAAO
O OOOOOO O OAOOOAAO
O OOOOOO O O OAAA A AO
O OOOOOO O O OAAA A AO
O OOOOOO O O OAAA A AO
O✕✕AAAAOOO–––AA✕
O✕O✕✕✕✕OOO–––✕✕✕
Zoom Copy
2-ORIGINAL H
COPY Margin Other
Functions
SORT
2 in 1 Copy
2 Page Copy
Book
Edge
Margin
Non-Sort
Sort
Sort-Rotate
Manual Skyshot
Interrupt
O: Possible Combined Functions.
✕: Unavailable Combined Functions.
A : Next Selection is Carried Out.
–: Indicates that SORT mode cannot be used. Non-sort operation is carried out.AOOOOOOOOOOOOAAO
1 \ 22 \ 2Book -> 2
2 \ 1
OOAAAAAOOOOOOAAO 1 \ 2
OOAAAAAOOOOOOAAO 2 \ 2
OOAAAAAOOOOOOAAO Book \ 2
OOAAAAAOOOOOOAAO 2 \ 1
Making Copies 
						

							28
NOTE

 

 


ProcedureFUNCTION Key
RESET Key
#Press the FUNCTION Key
$Press 1 (GENERAL FUNCTIONS) or 2
(COPIER SETTINGS) key. You may also use
the (G or F) keys.
%Press the SET key.
&Press the Keypad to select function modes
or use the (G or F) keys.
(Follow the on screen instructions.
)After setting, press the SET key to set up the
function.
CPlease refer to each option’s operating instructions for function settings.
Printer
Settings for
Key OperatorGeneral
Functions for
Key OperatorCopier
Settings for
Key OperatorLAN Settings
for Key
Operator
Input Identification Code
Printer
Settings

 

 


Using Function Modes to Change the Initial Copy Modes
General
FunctionsCopier
SettingsLAN Settings
Options
Function

Checking the Copier’s Total  Counter
To display the copier’s Total Counter, press the COPY SIZE and PAPER TRAY keys
simultaneously.COPY SIZE
KeyPAPER
TRAY Key
FUNCTION MODE  (1-2)
ENTER NO. OR ∨ ∧ 
						

							29
Making Copies
Function
No. ModesInitial
Setting Function
00 SORT MODE DEFAULT Selects the sort mode.
CNON-SORT, SORTNON-SORT
General Functions
05 Displays the amount of sort memory used on
the panel.
COFF, DISPLAYSORT MEMORY USAGEOFF
Copy usage and copy limit of the selected
department and total copy usage will appear
on the screen. DEPT. COUNTER Consult
your
service
technician. 06
08
09Select Sort-Rotate mode.
COFF, ON SORT-ROTATE DEFAULT OFF
KEY OPERATOR MODEInput the key operator ID code. 
						

							30
No.ModesInitial
Setting Function
00 MARGIN DEFAULT Selects the margin position and shift value.
CPOSITION (Left, Right, Top, Bottom)
CVALUE (5 - 99 mm)LEFT
10 mm
Copier Settings Function
Selects the edge mode (Equal Rate = set the
same value for X & Y or Individual = set the
value for X & Y individually) and width.
CEQUAL RATE (X & Y ), INDIVIDUAL
C5 - 99 mm EDGE DEFAULT
05 Selects whether or not to disable edge deletion.
CINVALID, VALID 2 in 1 WITH FRAMESelects the book Center Void margin width.
C5- 99 mm BOOK MARGIN DEF.EQUAL RATE
5 mm
20 mm
INVALID
Enables or disables the use of skyshot mode.
COFF, NORMAL, QUALITY DIGITAL SKYSHOT
NORMAL
OFF
VALID Enables or disables the use of Manual
Skyshot.
COFF; M1 ON; M2 ON; M1, M2 ON MANUAL SKYSHOT
Input key operator ID code. KEY OPERATOR MODEAutomatically adjusts the copy density for text
and photographic originals.
CINVALID, VALID AUTO EXPOSURE 01
02
06
07
08
14
PORTRAIT
L \ R Selects the orientation and layout for 2 in 1 Copy.
CORIENTATION (Portrait, LANDSCAPE)
CLAYOUT (L \ R, R \ L) 2 in 1 DEFAULT 12
L \ R Selects the 2 page mode.
CL \ R, R \ L 2 PAGE MODE DEF.
13
INVALID
Select the reduction ratio in margin mode.
CINVALID, VALID FRAME MARGIN 03
OFF
Function sets the duplex priority mode.
C
OFF, 1 \ 2, 2 \ 2, Book \ 2 (For DP-2010E)
2-SIDED MODE DEF. 04
09
10
11
LONG EDGESelects the binding location for 1 \ 2 Copy.
C
LONG EDGE, SHORT EDGE (For DP-2010E)
1 \ 2 BINDING DEF.
LONG EDGESelects the binding location for 2 \ 1 Copy.
C
LONG EDGE, SHORT EDGE (For DP-2010E)
2 \ 1 BINDING DEF.
FLIPPING
L \ R Selects the page order and book format for
Book \ 2 Copy.
1. BOOK FORMAT (1: FACING, 2: FLIPPING)
2. 
PAGE ORDER (1: L \ R, 2: R \ L) (For DP-2010E)
BOOK \ 2 DEFAULT
NOTECCertain Functions or Parameters are available for selection only when their
respective option is installed.