Home > Panasonic > Satellite TV System > Panasonic Directv Digital Satellite Receiver Tzdbs01 Operating Instructions

Panasonic Directv Digital Satellite Receiver Tzdbs01 Operating Instructions

    Download as PDF Print this page Share this page

    Have a look at the manual Panasonic Directv Digital Satellite Receiver Tzdbs01 Operating Instructions online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							10
    FRONT AND REAR VIEW OF THE DIGITAL SATELLITE RECEIVER
    Front and Rear View of the Digital Satellite Receiver
    Front Panel
    POWERTurns the Digital Satellite Receiver On.
    MENUPress to enter and exit Roller Guide Menu system.
    GUIDEPress to access the Advanced Program Guide™.
    INFOPress to display the Channel banner or to search within the
    Guide.
    ACTIONPress to enter selection from the Guide or from the Menu.
    NAVIGATION 
    BUTTONS Press the navigation arrows to move the highlight up, down, left
    or right.
    SMART CARDAlso known as Access Card, identifies you to your program
    providers. The DIRECTV System requires a valid card. (Slide the
    door to the right to access the smart card.)
    Notes:
    rDIRECTV programming sold separately.
    rProgramming subject to change. You must be physically located in the U.S. to receive
    DIRECTV service. DIRECTV services not available outside the U.S. DIRECTV
    programming is sold separately and independently of DIRECTV System hardware. A valid
    programming subscription is required to operate DIRECTV System hardware. Activate your
    DIRECTV programming today at 1-800 DIRECTV (1-800-347-3288).
    DI GI TAL SATELLI TE RECEI VERPanasonic
    MENU
    GUI DEINFO
    ACTI ON
    POWER
    Menu button
    Navi gati on buttons
    Navi gati on buttons
    Action button Gui de buttonInfo butttonSmar t Car d
    (behi nd door)Power button
    Power i ndi cator LED
    Remote Control  sensor 
    						
    							11
    FRONT AND REAR VIEW OF THE DIGITAL SATELLITE RECEIVER
    Rear Panel
    SATELLITE INUse to connect DIRECTV satellite dish antenna to the Digital
    Satellite Receiver.
    VHF/UHF INUse to connect an off-air antenna or cable TV signal to the 
    Digital Satellite Receiver. This input serves as a passthrough 
    for off-air antenna or cable signal when the user presses the 
    TV/SAT button or when the Digital Satellite Receiver is 
    powered off.
    VHF (SAT) / UHF Use to connect the Digital Satellite Receiver to your TV. 
    OUT
    NTSC OUTPUTUse to connect the Digital Satellite Receiver to a TV or
    Monitor. By using the audio/video jacks, you will get better
    picture and sound quality. 
    TEL LINEUse to connect a phone line to the Digital Satellite Receiver
    to enable receipt of certain DIRECTV
    ® services.
    SATELLI TE
    IN
    R- AUDI O- L VI DEO
    NTSC OUTPUTVHF/ UHF
    IN
    VHF ( SAT)  / UHF
    OUTTEL LINEAC IN
    SATELLITE IN jack
    VHF (SAT) /UHF
    OUT JackUHF/VHF IN Jack
    Tel Line NTSC OUTPUT
    AC POWER INPUT 
    						
    							12
    FEATURES OF THE DIGITAL SATELLITE RECEIVER
    Features of the Digital Satellite Receiver
    DIRECTV Channel Banner 
    The Channel Banner is available with DIRECTV® programming to show you which
    channel and program you are currently viewing or have selected. The following figure
    shows the DIRECTV channel banner. The DIRECTV channel banner description area
    can be expanded, if the user presses the INFO key. 
    In addition to viewing the program description, the user can add or remove the
    channel from the favorite channel list. This is accomplished by navigating left or right
    and pressing the ACTION key.
    Channel Banner: Favorite Channel List
    The favorite channel list is a customized list that allows you to create your own unique
    channel list. The favorite channel list is active when you select the “FAV CH” mode in
    the guide screen. By default, the “ALL CH” mode is selected. Also, by default, both the
    “ALL” mode and “FAV” modes default to all the channels selected in their lists. 
    When the description of the channel banner is expanded, the user now has the
    opportunity to add or remove a channel from the favorite list. By default, 
    Delete from FAV button is highlighted when the Channel Banner is expanded. Once
    a channel is removed from the favorite list, the user is required to numerically enter in
    the channel number to view that channel, at which time the user can add the channel
    back into the favorite channel list.
    The following figure depicts the Channel Banner, when the Description area is 
    highlighted.The DIRECTV Channel Banner
    DTVALL CH
    Any Given Sunday
    3:00 PM - 5:37 PM              Mon 10/30/00 3:23 PM
    Movie. Drama. (1999) Al Pacino, Cameron Diaz, Dennis
    Quaid. Oliver Stone scores with this tale of egos colliding on
    & off the pro football field. All Day Ticket. AC, AL. 
    Rating R
    CC
    DTV
    105
    ALL CHAny Given Sunday
    3:00 PM - 5:37 PM              Mon 10/30/00 3:23 PM
    Movie. Drama. (1999) Al Pacino, Cameron Diaz, Dennis
    Quaid. Oliver Stone scores with this tale of egos colliding on
    & off the pro football field. All Day Ticket. AC, AL. 
    Rating R
    CC
    ALL CH
    Channel Banner
    Delete from FAV 
    						
    							13
    FEATURES OF THE DIGITAL SATELLITE RECEIVER
    Channel Banner: Components
    The Channel Banner is used to show you which channel and program you are
    currently viewing or selecting. The figure below indicates the various components of
    the Channel Banner.
    The following figure displays some of the information that can possibly be displayed,
    simultaneously.Channel Banner Components
    System Clock
    Channel
    Name
    Channel Surf 
    Mode 
    (FAV or ALL CH)Channel
    NumberAlternate
    Audio IconRating LevelClosed 
    Caption
    Icon
    DescriptionTitle and duration
    Delete From FAV
    Channel Banner with OSD Messages
    Delete from FAV
    Audio Track (1of 2) English
    i
    Press INFO if you want to purchase this event.  
    						
    							14
    FEATURES OF THE DIGITAL SATELLITE RECEIVER
    Icons: Channel Banner
    The Channel Banner contains several icons that are displayed only when the feature
    is available and is supported by the Digital Satellite Receiver. The following figure and
    table depicts the location and appearance of these icons.
    Viewing Modes
    This section describes the user interface that is directly controlled by remote or front
    panel. The following operational modes are supported by this interface:
    • Tuning Mode
    • Recall Display Mode
    • Exiting Tuning Mode
    Normal Viewing Mode
    Normal Viewing Mode is defined as only the video being displayed and possibly
    closed captioning data. When Digital Satellite Receiver is first powered on, it will be in
    the Normal Viewing mode.
    Note:The first time the Digital Satellite Receiver is powered On, all channels except those
    exceeding the MPAA or TV rating limits and channels not authorized by DIRECTV are
    shown.
    Once the user has created a favorite channel list, the Digital Satellite Receiver will
    channel surf only to channels that are part of the favorite channel list. The user may
    tune to a channel that is not a member of the favorite channel list by entering in a
    channel number, explained in the Direct Tuning Method section. The user must add
    this channel using the menu system.
    Icon NameIcons DescriptionIcon Appearance
    MessagesIndicates that there is an unread
    message.
    LockIndicates that the channel is locked
    due to either limits on spending or
    by content advisory.
    Alternate AudioIndicates that the current program
    has multiple audio tracks.
    Closed CaptioningIndicates that the program has
    Closed Captioning.
    CC 
    						
    							15
    FEATURES OF THE DIGITAL SATELLITE RECEIVER
    Power On Requirements
    When the Digital Satellite Receiver is powered on, the receiver will tune to the last
    tuned channel. If this channel no longer exists, the receiver will tune to channel 100.
    Prior to initial setup of the receiver, the receiver may automatically go to Setup menu
    or tune to channel 100.
    Tuning Mode
    The Tuning Mode happens when the user attempts to change the channel. The Digital
    Satellite Receiver will support 3 ways to change the channel, as outlined below:
    Direct Tuning Method
    The Digital Satellite Receiver supports the tuning of either single or compound
    channel numbers. The single channel numbers range from (0 to 9999) and compound
    channel numbers (major-minor) can range from (0-0 to 999-99)*. The compound
    channel number uses the “PROG” button to enter the minor number field. Following is
    an example of Direct tuning screen. 
    *For example, 120-1 is an example of a compound number. 120 is the major number
    and 1 is the minor number.
    MethodResult
    • Direct Tuning (0-9 and PROG keys)Tunes directly to a channel using
    either single or compound numbers.
    • Channel UP/Down Tuning (pqkeys)Tunes to the next/previous available
    channel.
    • Rapid Tune (R-TUNE)Switches between the last two
    channels, accessed. This is
    accomplished using the R-TUNE key
    on the remote.
    Star Battle  9:00 PM - 10:00 PM 
    9:15 PM Sun 3/21/01 
    “The battle of the universe begin when the evil…”  
    345-78 
    MSNBC 
    FAV CH 
    CC        RATING: TV- PG    
    Direct Tuning example 
    						
    							16
    FEATURES OF THE DIGITAL SATELLITE RECEIVER
    Tuning Mode (Cont.)
    Example of Non-compound (Single) Channel Number Input
    For example, to tune channel 345, you enter the channel number by using the number
    keys (0-9) on the remote control. Then press the ACTION button which causes the
    tuning event to occur.
    Example of Compound Channel Number Input
    A compound numbers (major-minor) can range from (0-0 to 999-99). For example, to
    enter channel number 345-78, you do the following.
    • Press the numeric buttons 3, 4 and 5 on the remote control.
    •Press PROG button to enter the minor number field.
    • Press number 7 and 8 buttons on the remote control.
    •Press ACTION button to complete the tuning event.
    Note:If you do not enter a number after 3 seconds, the number 0 is assumed for the minor
    number.
    Unavailable Channel Selection
    The “Channel Not Available” screen is displayed when you select an unavailable
    channel. The following is a list of some possible situations where an unavailable
    channel selection may occur.
    rTuning to a channel that is not transmitting any programs.
    rTuning to a channel that is blocked either by spending or content advisory limits.
    rThe signal strength of the RF signal is insufficient to obtain consistent error free data.
    Following is a example of Channel Not Available screen.
    The following is an example of insufficient credit.
     Rating Limit Exceeded.
    Press ACTION to Override.
    11 9
    DTV
    ALL CHRandom Hearts
    4:30 PM - 5:45 PM
    Wed 05/03/00 6:00 PM
    Movie, Drama, Harrison Ford, Kristin Scott Thom
    Rating: R
    Channel Not Available Screen
    For ordering information, please callicustomer service, ext. 732. 
    						
    							17
    GETTING STARTED
    Getting Started
    Step 1. Connect AC Power Cord
    Plug the AC power cord into a grounded outlet.  Do not turn on any devices until you
    have finished making all necessary connections.
    Step 1a. DIRECTV Satellite dish Connection
    Connect the DIRECTV Satellite dish downlead to the Satellite In jack on the rear panel
    of the Digital Satellite Receiver.
    Note:With this receiver and the proper satellite dish antenna, you may be able to subscribe
    to local channels from DIRECTV in certain markets. Additional equipment may be
    required in some areas. Check with your retailer or visit DIRECTV.com for information
    on availability of local channels from DIRECTV in your area.
    Step 1b. Antenna/Cable Connection
    Connect the antenna or cable wire to the VHF/UHF IN jack on the rear panel of the
    Digital Satellite Receiver. The signal from the terrestrial antenna or cable will be
    passed through when the user presses the TV/SAT button on the remote control or
    when the digital satellite receiver is off. The RF output of the Digital Satellite Receiver
    must be connected to the television.
    SATELLITE
    IN
    R- AUDIO- L VI DEO
    NTSC OUTPUTVHF/UHF
    IN
    VHF  ( SAT)  / U HF
    OUTTEL LINEAC IN
    SATELLITE
    DISH
    SATELLITE
    IN
    R- AUDIO- L VI DEO
    NTSC OUTPUTVHF/UHF
    IN
    VHF (SAT) /UHF
    OUTTEL LINEAC IN
    CABLE OR OFF-AIR ANTENNA 
    						
    							18
    GETTING STARTED
    Step 1c. Digital Satellite Receiver connection to TV or Monitor
    Follow this diagram when connecting the Digital Satellite Receiver to a Television or 
    Monitor.
    Procedure
    • Connect the VHF (SAT) /UHF OUT to the ANT IN of the television or connect video cable
    from the video output jack on the Digital Satellite Receiver to the video input jack on the TV.
    • Connect audio cables from the left and right NTSC audio output jacks on the Digital
    Satellite Receiver to the left and right audio input jacks on the TV.
    To receive off-air programming (no cable box)
    • Turn off the Digital Satellite Receiver or press TV/SAT button to toggle.
    • Tune TV to desired channel.
    To receive off-air programming (with cable box)
    • Turn off the Digital Satellite Receiver or press TV/SAT button to toggle.
    • Tune TV to cable box output channel (either CH3 or Ch4).
    • Tune the cable channels using the cable box.
    Note:Modem should also be connected to a telephone jack using the cable supplied RJ11C
    cable if impulse pay per view services are desired.
    DIGITAL SATELLITE RECEIVER CONNECTION TO TV OR MONITOR
    SATELLI TE
    IN
    R- AUDI O- L VI DEO
    NTSC OUTPUT
    TEL LINEAC IN
    Incomi ng si gnal  from
    cabl e or antennaTV
    ANT I N
    INPUT
    AUDI O
    RL
    VI DEO
    Digital Satellite Receiver
    VHF ( SAT)  / UHF
    OUT VHF/ UHF
    IN
    NOTE: A/V CABLES AND MODEM
    CABLE INCLUDED. 
    						
    							19
    GETTING STARTED
    Step 1d. Digital Satellite Receiver, Satellite dish, Cable box and terrestrial antenna
    Follow this diagram if you have Satellite service, cable box and terrestrial antenna.
    Cable or terrestrial antenna signal is passed through when you press TV/SAT button
    to toggle or when the Digital Satellite Receiver is turned off.
    Procedure
    • Connect the antenna cable to one of the inputs (A or B) of the A/B switch.
    • If using a cable box, connect the cable wire from the wall jack to the cable box ANT
    (antenna) IN jack using a standard RF cable with coaxial connector and connect the cable
    box ANT (antenna) OUT jack to the other input (A or B) of the A/B switch.
    • If not using a cable box, connect the cable wire from the wall jack to the second input of the
    A/B switch using an RF cable (not shown).
    • Connect the OUT signal of the A/B switch to the ANT IN jack of the Digital Satellite
    Receiver.
    • Connect the VHF (SAT) /UHF OUT jack to the Conventional TV or Monitor by using a RF
    cable.
    • Connect the NTSC OUTPUTS of the Digital Satellite Receiver to the A/V inputs of the
    television or monitor.
    Note:If viewing video using RF Input, select either CH 3 or CH 4 in TV Output section in the
    Setup menu. Tune your television to the same channel (either CH 3 or CH 4).
    DIGITAL SATELLITE RECEIVER, SATELLITE DISH, 
    CABLE BOX AND TERRESTRIAL ANTENNA
    SATELLI TE
    IN
    TEL LINER- AUDI O- L VI DEO
    NTSC OUTPUT
    AC IN UHF/ VHF
    INVHF ( SAT)  / UHF
    OUTANT I N
    VI DEO R- AUDI O- L
    A/ B SWI TCH
    ANT I NANT OUT
    CABLE BOX
    TV Digital Satellite Receiver
    NOTE: A/V CABLES AND MODEM
    CABLE INCLUDED. 
    						
    All Panasonic manuals Comments (0)

    Related Manuals for Panasonic Directv Digital Satellite Receiver Tzdbs01 Operating Instructions