Panasonic Dmc Fz10 Operating Instructions Manual

							Playback (advanced)
111
 You can only load pictures from the 
camera and cannot write them on the 
card or delete them.
 Use the supplied USB connection 
cable only.
 When there are 1000 or more pictures 
on the card, the pictures may not be 
imported.
 When the PC recovers from the 
standby mode while connecting it to a 
camera with USB connection cables, 
they may not properly communicate 
each other.
FZ10-PP.book  111 ページ  ２００３年１１月１８日　火曜日　午後１時７分 
						

							Playback (advanced)
112
Connecting to a Printer
By connecting the camera directly to a printer supporting PictBridge or USB 
Direct-Print via the USB connection cable (supplied), you can select the pictures to 
be printed or start printing.
1Turn the camera on and then set 
the [USB MODE] to [PTP] 
(PictBridge) or [Mass Storage] 
(USB Direct-Print). (P107)
2Turn on a printer.
3Connect the camera to the printer 
via the USB connection cable 
(supplied).
¬Suggestions/Tips ¬
 Ask the manufacturer of the printer 
about the corresponding models. 
(Read the printer operating 
instructions too.)
 If the remaining battery power 
becomes low during communication, 
the power indicator blinks and the 
alarm beeps. In this case, stop the 
communication. Then turn the camera 
off and charge the battery.
 When connecting to a printer, we 
recommend using the AC adaptor as 
the power source.
 Disconnect the USB connection cable 
and DC cable after printing.
 Use the supplied USB connection 
cable only.
A/V
OUT
USB
FZ10-PP.book  112 ページ  ２００３年１１月１８日　火曜日　午後１時７分 
						

							Playback (advanced)
113
Using a Printer (PictBridge)
Preparation
 Connect the camera to a printer. (P112)
 Set the paper size and print quality. (Read the printer operating instructions.)
ªSingle picture
1Select [SINGLE PICTURE].
 The screen shown in step 2 
appears when DPOF print is not 
set or the printer does not support 
DPOF print.
2Select the picture to print.
3Select [YES] and print.
 Press the [DISPLAY] button to print 
the date. (Only when connecting to 
the printer supporting to printing 
the date.)
Press 3 and then press 2/1 to 
set the number of prints. Press 4 
to print pictures.
 Press the [MENU] button to cancel 
printing.
SINGLE
PICTUREDPOF
PICTURE
SET
WB
REVIEWSET
WB
REVIEW
SETSELECT
PictBridge
SET
WB
REVIEWSET
WB
REVIEW
PRINTSELECT
2304
100_
00011/19
PLEASE SELECT
THE PICTURE TO PRINT
PictBridge
SET
WB
REVIEWSET
WB
REVIEW
PLS CHECK THE PRINTER
START PRINTING?
DATEDISPLAYSELECTSET COUNT
SET
COUNT1
YESNO
PictBridge
FZ10-PP.book  113 ページ  ２００３年１１月１８日　火曜日　午後１時７分 
						

							Playback (advanced)
114
Preparation
 Connect the camera to a printer. (P112)
 Set the DPOF print with this camera in advance. (P91)
 Set the paper size and print quality. (Read the printer operating instructions.)
ªDPOF picture
1Select [DPOF PICTURE].
 Press the [MENU] button, and you 
can change the DPOF print setting. 
(P91)
 When printing under the new 
settings, disconnect the USB 
connection cable and connect it to 
the printer again.2Select [YES] and print.
 Press the [DISPLAY] button to print 
the date. (Only when connecting to 
the printer supporting to printing 
the date.)
 Press the [MENU] button to cancel 
printing.
¬Suggestions/Tips ¬
 When the total number of prints becomes 1000 or more, the number of remaining 
pictures may appear as [---] on the screen.
 When connecting to a printer not supporting DPOF, DPOF printing cannot be set. 
(The DPOF print selecting screen does not appear.)
 Do not disconnect the USB connection cable when the cable disconnection 
warning icon [ ] is indicated.
 When the [¥] indication lights in yellow during printing, check if there is no 
malfunction on the printer.
 When the printer does not support the date printing by DPOF setting, the date may 
not be printed as it is on date setting in DPOF setting.
 When you do not set the date print setting, also check the date print setting on the 
printer.
SET
WB
REVIEWSET
WB
REVIEW
SINGLE
PICTUREDPOF
PICTURE
SETSELECT
PictBridge
SET
WB
REVIEWSET
WB
REVIEW
DATEDISPLAYSELECT
SET
PLS CHECK THE PRINTER
START PRINTING?
YESNO
PictBridge
FZ10-PP.book  114 ページ  ２００３年１１月１８日　火曜日　午後１時７分 
						

							Playback (advanced)
115
Using a Printer (USB Direct-Print)
Preparation
 Connect the camera to a printer. (P112)
 Set the paper size and print quality. (Read the printer operating instructions.)
ªSingle picture
1Select [SINGLE PICTURE].
 The screen shown in step 2 
appears when DPOF print is not 
set.
2Select the picture to print.
3Select [YES] and print.
 Press the [DISPLAY] button to print 
the date.
Press 3 and then press 2/1 to 
set the number of prints. Press 4 
to print pictures.
 Press the [MENU] button to cancel 
printing.
SET
WB
REVIEWSET
WB
REVIEW
SETSELECT
DIRECT PRINT
SINGLE
PICTUREDPOF
PICTURE
SET
WB
REVIEWSET
WB
REVIEW
PRINTSELECT
2304
100_
00011/19
PLEASE SELECT
THE PICTURE TO PRINT
DIRECT PRINT
SET
WB
REVIEWSET
WB
REVIEW
PLS CHECK THE PRINTER
START PRINTING?
DATEDISPLAYSELECTSET COUNT
SET
COUNT1
YESNO
DIRECT PRINT
FZ10-PP.book  115 ページ  ２００３年１１月１８日　火曜日　午後１時７分 
						

							Playback (advanced)
116
Preparation
 Connect the camera to a printer. (P112)
 Set the DPOF print with this camera in advance. (P91)
 Set the paper size and print quality. (Read the printer operating instructions.)
ªDPOF picture
1Select [DPOF PICTURE].
 Press the [MENU] button, and you 
can change the DPOF print setting. 
(P91)
 When printing under the new 
settings, disconnect the USB 
connection cable and connect it to 
the printer again.2Select [YES] and print.
 Press the [DISPLAY] button to print 
the date.
 Press the [MENU] button to cancel 
printing.
¬Suggestions/Tips ¬
 When the total number of prints 
becomes 255 or more, the number of 
remaining pictures appears as [---] on 
the screen.
 When you set the date print setting by 
pressing the [DISPLAY] button, the 
date is printed regardless of the date 
print setting on DPOF setting. (P95)
 When the printer does not support the 
date printing by DPOF setting, the 
date may not be printed as it is on date 
setting in DPOF setting.
 When you do not set the date print 
setting, also check the date print 
setting on the printer.
SET
WB
REVIEWSET
WB
REVIEW
SETSELECT
DIRECT PRINT
SINGLE
PICTUREDPOF
PICTURE
SET
WB
REVIEWSET
WB
REVIEW
PLS CHECK THE PRINTER
START PRINTING?
DATEDISPLAYSELECT
SET
YESNO
DIRECT PRINT
FZ10-PP.book  116 ページ  ２００３年１１月１８日　火曜日　午後１時７分 
						

							Others
117
Others
Using the MC Protector/ND Filter
The MC protector (DMW-LMC72; optional) is a transparent filter which affects 
neither the colors nor the amount of light, so it can always be used to protect the 
camera’s lens.
The ND filter (DMW-LND72; optional) reduces the amount of light to approximately 
1/8th (equal to adjusting the aperture value 3 increments) without affecting the color 
balance.
1Remove the lens cap and the lens 
ring.
2Attach the lens hood.
3Attach the MC protector 1 or the 
ND filter 2.
 Cap 3 (supplied with MC 
protector)
¬Suggestions/Tips ¬
 The lens cap supplied with the camera 
cannot be attached to the MC 
protector or the ND filter.
 You cannot attach the MC protector 
and the ND filter at the same time.
 When taking pictures with the flash 
using the MC protector/ND filter, 
vignetting effect may occur.
 When the MC protector/ND filter fell, 
they may be destroyed. Be careful not 
to drop them when attaching.
 The cap supplied with MC protector 
can also be used for the ND filter.
MCu“Multi-coated”
NDu“Neutral Density”
FZ10-PP.book  117 ページ  ２００３年１１月１８日　火曜日　午後１時７分 
						

							Others
118
After Use
After using the camera, it is recommended that you complete the following steps:
1Turn the camera off and close the 
flash.
2Remove the card and the battery. 
(P15, 19)
3Remove the lens hood (only when 
using it) and attach the lens ring 
and the lens cap.
 When removing the lens hood, hold 
the whole of the lens hood gently 
and then rotate it 
counter-clockwise. (It may hard to 
rotate the lens cap if you hold its 
edge.)
¬Suggestions/Tips ¬
 If you will not be using the camera for 
a long time,
– Remove the battery. (When you 
insert the battery again, set the 
clock.)
– Do not keep the camera in a place 
where it will be subjected to high 
temperatures, high humidity or soot. 
Fungus may be attached to the lens 
or condensation may occur.
– Keep the camera in a cool, dry and 
well-ventilated place and avoid 
storing near dust or chemicals.
– We recommend keeping it in a 
closed case with the desiccant.
OFF ON
FZ10-PP.book  118 ページ  ２００３年１１月１８日　火曜日　午後１時７分 
						

							Others
119
Screen Display
ªIn recording
1 Recording mode
2 Flash (P38)
3 Conversion lens (P86)
4 White balance (P67)
5 ISO sensitivity (P74)
6 Picture size (P71)
7 Quality (P72)
8 Battery indication (P13)
9 Jitter alert indication (P33)
10 Frame/Time remain
In Motion image mode: e.g. 11S
11 Audio recording (P75)
12 Focus indication (P31)
13 Recording indication
14 Self-timer (P43)
15 Card access indication (P17)
16 AF area (P31)
17 Histogram (P29)
18 Aperture indication/Shutter speed 
indication (P31)
19 Program shift indication (P35)
20 Exposure compensation (P41)21 Auto bracket (P42)
22 Program shift setting indication 
(P35)
23 Spot AF area (P73)
24 Spot metering target (P73)
25 Zoom/Digital zoom (P37, 77)
26 Flash output adjustment/External 
flash (P40, 84)
27 Burst (P44)
28 Optical image stabilizer (P80)
29 Color effect (P78)
30 Continuous AF (P76)
 Current date and time appear for 
about 5 seconds after turning the 
camera on or setting the clock. (P22)
1234 5 6 7 8
9
11
13 12 10
14
16 15
17
21 22
23
24
25
26
27
28
29 30
18 20 19
1/25
PROGRAM SHIFT
F2.8
P2304
19COOL
H
ISO100
C_
AF1
WT24X
FZ10-PP.book  119 ページ  ２００３年１１月１８日　火曜日　午後１時７分 
						

							Others
120
ªIn playback
1 Playback mode
2 DPOF (P91, 98)
 (White):
DPOF setting for printing
 (Green):
DPOF setting for Slide Show
 (Green with number of prints): 
DPOF setting for printing and 
Slide Show
3 Protected picture (P96)
4 Picture with audio (P88)
5 Picture size (P71)
: In Motion image mode
6 Quality (P72)
: In Motion image mode
7 Battery indication (P13) 
8 Folder/File number
9 Page number/Total pictures
10 Histogram (P29)
11 Recording information
12 Recorded date and time
13 Audio playback (P88)
: In Motion image mode
14 Flip animation (P81)
PF2.8 1/25
2304
10:00  DEC. 1.2003
100_
0001
1/19
ISO100AUTO
1
8 234 675
9
14
1
0
11
12
1
13PLAY AUDIO
1
1
1
PLAY MOTIONIMAGE
FZ10-PP.book  120 ページ  ２００３年１１月１８日　火曜日　午後１時７分