Panasonic Ey7460 Operating Instructions Manual

Cordless Drill & Driver/Cordless Hammer Drill & Driver
Perceuse-visseuse sans  fi l/Perceuse à percussion-visseuse sans  fi l
Destornillador y taladro sin cables/Destornillador y taladro percutor si\
n cables
Operating Instructions
Instructions dutilisation
Manual de instrucciones
Model No: EY7460/EY7960
IMPORTANT
This manual contains safety information. Read manual completely before f\
irst using this product and save this manual for 
future use.
IMPORTANTCe mode d’emploi contient des informations sur la...

- 2 - 
(A)Keyless drill chuckMandrin porte-foret sans fi l Mandril sin llave
(B)Clutch handle Poignée de l’embrayage Mango de embrague
(C)Speed selector switchInterrupteur de sélection de vitesseInterruptor selector de velocidad
(D)Forward/Reverse lever Levier d’inversion marche 
avant-marche arrière Palanca de avance/inversión
(E)Alignment marks
Marques d’alignement Marcas de alineación
(F)Battery pack release buttonBouton de libération de 
batterie autonome Botón de liberación de batería
(G)Battery pack...

- 3 -  
I. INTRODUCTION
These tools can be used to tighten 
screws in clutch mode and to drill 
holes in wood and metal in drill mode. 
Additionally, model EY7960 can be 
used to drill holes in soft concrete and 
similar materials in hammer mode. 
II. GENERAL SAFE-
TY RULES
 WARNING! Read all instructions
Failure to follow all instructions listed below 
may result in electric shock, fire and/or 
serious injury. The term “power tool” in all 
of the warnings listed below refers to your 
main operated...

- 4 - 
 7) If devices are provided for the 
connection of dust extraction and 
collection facilities, ensure these 
are connected and properly used.
  Use of these devices can reduce 
dust related hazards.
Power Tool Use and Care
 1) Do not force the power tool. Use 
the correct power tool for your 
application.
  The correct power tool will do the job better and safer at the rate for 
which it was designed.
 2) Do not use the power tool if the 
switch does not turn it on and off.
  Any power tool that...

- 5 -  
 3)  Hold power tools by insulated grip-
ping sur faces when performing an 
operation where the cutting tool 
may contact hid den wiring.
  Contact with a “live” wire will make ex  posed metal parts of the tool 
“live” and shock the operator.
 4)  
Be aware that this tool is always in 
an operating condition, since it does 
not have to be plugged into an elec-
trical outlet.
  5) If the bit becomes jammed, imme- diately turn the trigger switch off 
to prevent an overload which can 
damage the...

- 6 - 
IV. FOR  BATTERY CHARGER & 
BAT TERY PACK
Important Safety Instructions
 1) SAVE THESE IN  STRUCTIONS -This 
manual contains important safety 
and operating instructions for bat-
tery charger EY0L80.
  2) Before using battery charger, read  all instructions and cautionary mark-
ings on (1) battery charger, (2) bat-
tery pack.
 3)  CAUTION 
- - To reduce the risk of in-
jury, charge only Panasonic Battery 
Pack as shown in last page.
 
Other types of batteries may burst 
causing personal injury and...

- 7 -  
 23) Do not short the battery pack. A bat-
tery short can cause a large current 
flow, over heating and burns.
 24)  NOTE: If the supply cord of this appli-
ance is damaged, it must only be re-
placed by a repair shop appointed by 
the manufacturer, because special 
purpose tools are required.
  25)  TO REDUCE THE RISK OF ELEC- TRIC SHOCK, THIS APPLIANCE 
HAS A POLARIZED PLUG (ONE 
BLADE IS WIDER THAN THE 
OTHER).
  This plug will fit in a polarized outlet  only one way. If the plug does not fit...

- 8 - 
Attaching or Removing Bat-
tery Pack
1. To connect the battery pack:
Line up the alignment marks and at-tach 
the battery pack.
  Slide the battery pack until it locks into position.
Alignment marks
2. To remove the battery pack:
Push on the button from the front to re-
lease the battery pack.
Button
Support handle
Place the support handle at your favorite 
position and tighten the handle securely.
Tighten
Loosen
Remove the handle when placing the 
tool in the storage case.
VI. OPERATION
[Main...

- 9 -  
3. After use, set the lever to its center position (switch lock).
Clutch Torque Setting
Adjust the torque to one of the 18 
clutch settings or    position 
(EY7460).
Adjust the torque to one of the 18 
clutch settings or  
 ,    position 
(EY7960).
NOTE:
Always make sure to stop operation 
of the tool and disengage it from 
the work, when you select Ham-
mering mode from Drilling mode 
or when you shift to Drilling mode 
from Hammering mode by rotating 
clutch handle.
CAUTION:
Set the clutch...

- 10 - 
Control Panel
(1)(2) (3)
(1) LED light
Before the use of LED 
light, always pull the 
power switch once.
Press 
 the LED light 
button.
The light illuminates with 
very low current, and it 
does not adversely af-
fect the performance of 
the tool during use or its 
battery capacity.
CAUTION:
• The built-in LED light is designed to  illuminate the small work area tempo-
rarily. 
• Do not use it as a substitute for a  regular flashlight, since it does not 
have enough brightness.
•  LED light turns...