Panasonic LCD Projector PT-LB60NTU PT-LB60U Operating Instructions

							
ENGLISH-31
Useful functions

Projector control
panel
Correcting the image position
automatically (AUTO SETUP)
This projector can adjust the position of the image and the settings for\
 “DOT
CLOCK” and “CLOCK PHASE” when RGB signals are being input.Press the AUTO SETUP button while RGB
signals are being projected.
BAutomatic positioning
will be carried out.
NOTE:
B“SIGNAL SEARCH” will also be carried out. (When “SIGNAL SEARCH\
”
is set to “ON”, refer to page 51 for details.)
B If the dot clock frequency is 100 MHz or higher, “DOT CLOCK”, and
“CLOCK PHASE” will not be adjusted automatically. Refer to page 45\
 for
details.
B If the edges of the projected image are indistinct, or if a dark picture\
 is
being projected, the automatic setup processing may stop automatically
before it is complete. If this happens, project a different picture and \
then
press the AUTO SETUP button again.
[

Projected
image
Screen 
						

							
32-ENGLISH
Turning off the picture and sound
momentarily (SHUTTER)
The “SHUTTER” function can be used to momentarily turn off the pic\
ture and
sound from the projector when the projector is not being used for short
periods of time, such as during breaks in meetings or when carrying out
preparation. The projector uses less power in “SHUTTER” mode than \
it does
in normal projection mode.Press the SHUTTER button.
BThe picture and sound will be turned off.
B Press any button on either the projector or
remote control unit to return to normal operating
mode.
NOTE:
BYou can also select “SHUTTER” from the on-
screen menu (refer to page 53).
Adjusting the volume (VOLUME)
You can adjust the volume of the sound that is output from the projector\
’s
built-in speaker and VARIABLE AUDIO OUT connector.
Press the VOLUME +/- button.
BPress the + button to raise the volume.
B Press the - button to lower the volume.
NOTE:
BYou can also select “VOLUME” from the on-
screen menu (refer to page 52). 
						

							
ENGLISH-33
Enlarging the picture (DIGITAL ZOOM)
You can enlarge the projected image and move the enlarged area.BThe picture will then be enlarged to 1.5 times the
normal size.
BPress the MENU button to return to the normal screen.
Press the DIGITAL ZOOM +/- button.
NOTE:
B
The enlargement ratio can be changed within the range of 1x to 2x, in
steps of 0.1. When RGB signals are being input, the enlargement ratio
can be changed within the range of 1x to 3x, except when the “FRAME
LOCK” is set to “ON” (page 47).
B If the type of signal being input changes while the digital zoom functio\
n
is being used, the digital zoom function will be cancelled.

Button functions when using “DIGITAL ZOOM”
+button The enlargement ratio will increase.
- button The enlargement ratio will decrease.
FGbuttons The displayed position will move
upward or downward.
IHbuttons The displayed position will moveto the left or right.
Menu operation
(on connector panel)
Useful functions 
						

							
34-ENGLISH
Displaying two screens (INDEX WINDOW)
This function lets you store a picture which is being projected into mem\
ory,
so that you can display a still picture and a moving picture on the scre\
en.BThe current moving picture will be captured in a
still window.
B Press the MENU button to return to the previous
screen.
Press the INDEX WINDOW button.
NOTE:
B
The aspect ratio of the screen changes and the image is vertically
elongated in comparison to a normal image.
B When the screen size is changed, the picture’s aspect ratio will also\
change. Make sure that you fully understand the notes on “ASPECT” \
on
page 47 before using the “INDEX WINDOW” function.
B You can also select “INDEX WINDOW” from the on-screen menu (refer
to page 53).

Moving
pictureStill
picture Moving
picture
Button functions when using “INDEX
WINDOW”
Press the 
For Gbutton to select a screen
size.
It can switch to three stages.
Still
picture Moving
pictureStill
picture Moving
pictureStill
picture Moving
picture
Press the II or  H
H
button to switch
between the still picture screen and
moving picture screen.
Press the ENTER button to capture the
present moving picture in a still window.
Still
picture Still
picture
Moving
picture Moving
picture
Menu operation
(on connector panel) 
						

							
ENGLISH-35
BA pointer will be displayed in the middle of the
projected image.
B Press the POINTER button to cancel the pointer
display.
Press the POINTER button.
NOTE:
B
The pointer cannot be displayed when a menu screen is being
displayed. Moving the pointer
Press the 
FGIHbuttons to move the
pointer.

You can select the pointer in “POINTER
SELECT ” from 3 types (refer to page 50).
Pointer1 Pointer2 Pointer3
Displaying the pointer (POINTER)
You can display the pointer on the projected images.
Useful functions


The pointer will move in 4 directions as shown
below. 
The pointer will move in 8 directions as shown
below.

Menu operation
(on connector panel) 
						

							
36-ENGLISH
On-screen menus
Menu screens
The various settings and adjustments for this projector can be carried o\
ut by
selecting the operations from on-screen menus.
The general arrangement of these menus is shown below.Menu Screen
(When a VIDEO signal is being
input )

POSITION menu  (page 44)

BPress the MENU button to
display the menu screen.
Refer to page 38 for details on
how to operate the on-screen
menus.
B
The illustrations of the on-screen
menus in this operating instructions
are for the PT-LB60NTU.
PICTURE menu  (page 40) 
						

							
ENGLISH-37
Adjustments and settings

2/2

LANGUAGE menu (page 48)
SECURITY menu (page 54)

WIRELESS menu  (page 56)
(PT-LB60NTU only)
OPTION menu  (page 49)
G     F
G     F 
						

							
38-ENGLISH
#Press the MENU button.
$ Press the  F
F
or G
G
button to select an item
from the main menu on the left side.
% Press the ENTER button.
Menu operation guide

The menu screen will be displayed.
The selected item will be displayed in
orange.
The sub-menu for the selected item will
be displayed on the right side.
You can select an item from the sub-menu.

NOTE:
B Press the MENU
button to return to
the previous
screen.

Menu operation
(on connector panel) 
						

							
ENGLISH-39
Adjustments and settings
&Press the  F F
or G G
button to select an
item, and then press the  I
I
or H
H
button to adjust the value or change
the setting.
If adjusting the items in the “PICTURE”
and “POSITION” menus, the menu
screen will disappear and only the
selected item will be displayed.
The value and setting indicator will turn
green when any adjustment changes
from the factory set value. For items
without any selective setting or bar
scale, press the ENTER button. The
next screen for the item will then be
displayed.Unavailable on-
screen menu items
This projector has
unadjustable items and
unusable functions
depending on the signal
being input.
If an item cannot be adjusted
or a function cannot be used,
you cannot select the
corresponding item.
Returning a setting to the factory default
If you press the DEFAULT button on the remote control unit, you can retu\
rn
settings to the factory default settings. However, the operation of this\
 function
varies depending on which screen is being displayed.B
B
When a menu screen is being displayed
All the items on the sub-menu which is being displayed will be returned \
to
their factory default settings, and the value and setting indicator will\
appear white.
B
B
When an individual adjustment screen is being displayed
Only the item displayed will be returned to the factory default setting,\
 and
the value and setting indicator will appear white.

NOTE:
BA triangle symbol below a bar scale
indicates the factory default setting.
Items which do not have this triangle
symbol cannot be returned to the factory
default setting. The positions of the
triangle symbols vary depending on the
type of signal being input. Indicates the current
adjustment value
Indicates the standard
factory default setting  
						

							
40-ENGLISH
Adjusting the picture
#Press the MENU button to display the menu screen.
$ Select the “PICTURE” menu from the main menu, and then press the
ENTER button.
% Press the F or G button to select an item.
& Press the  Ior H button to adjust the value or change the setting. For
items with selective setting or a bar scale, the individual adjustment
screen will be displayed. For “DETAILED SETUP”, press the ENTER
button to display the next screen.
When an S-VIDEO/VIDEO signal is
being input When WIRELESS is selected
When an RGB signal is being input  When an YP
BPRsignal is being
input
PICTURE MODE

When an S-VIDEO/VIDEO/YPBPR
signal is being input
When an RGB signal is being input
or WIRELESS is selected
Select the picture mode that best
matches the image source and
room conditions.