Panasonic Monitor Bt Lh2550p Owners Manual

31
■CALIBRATION
Select CALIBRATION in the “SYSTEM CONFIG” menu to open the following menus.
*1 “EXECUTING” is displayed during “AUTO CALIBRATION” and “COMPLETE” appears when calibration ends. “INCOMPLETE” appears if calibration could not be completed. 
*2 When “RESET” ends, “COMPLETE” appears.
1. Press [ , ] in the “SYSTEM CONFIG” menu,
select the [CALIBRATION] submenu and press
[ENTER].
2. Press [ , ], select the [AUTO CALIBRATION] submenu and press [ENTER].
3. Select “YES” and press [ENTER].  This...

32
Underlined values indicate factory defaults.
*1 Changes in settings change menu settings. 
FUNCTION
Sub menu Settings Description
FUNCTION 1 - 
FUNCTION 5 HV DELAY
AUTOSETUP
BLUE ONLY
GAMMA SELECT
COLOR SPACE
SD ASPECT
SCAN
TWO WINDOW
SUB INPUT SEL.
WFM/VECTOR
MARKER
LEVEL METER
CROSS HATCH
MONO
TIME CODE
CLOSED 
 CAPTION
ANAMO
UNDEF
(Factory default: 
FUNCTION1:
 MARKER
FUNCTION2:
 WFM/VECTOR
FUNCTION3:
 TWO WINDOW
FUNCTION4:
 TIME CODE
FUNCTION5:
 LEVEL METER) Selects functions to be assigned to...

33
■FUNCTION setting restrictions
Settings are not available under the following conditions.
 
Setting Conditions that disable operation
HV DELAY In TWO WINDOW and WFM mode, “INVALID FUNCTION” appears to indicate that 
operation is disabled.
When “RGB-COMP.” is selected under “YP
BPR/RGB” or “DVI-COMP.” is selected under 
“DVI-D” in the “INPUT SELECT” menu, “INVAL ID FUNCTION” appears to indicate that 
operation is disabled.
AUTO  S ETUP When something other than “RGB-COMP.” is selected under “YP...

34
Main Menu (continued)
■Functions displayed during FUNCTION button operation
Pressing any of the [FUNCTION1] to [FUNCTION5] buttons  displays the operations assigned to each button as
shown below. 
 DELAY OFF, H DELAY, V DELAY, HV DELAY
 AUTOSETUP COMP.AUTOSETUP, COMPLETE, INCOMPLETE, 
NOT RGB-COMP.CH
 BLUE ONLY ON, BLUE ONLY OFF
 GAMMA SELECT GAMMA STANDARD, GAMMA FILM, 
GAMMA STDIO/PST
 COLOR SPACE SMPTE-C, COLOR SPACE EBU, 
COLOR SPACE ITU-709, COLOR SPACE WIDE1, 
COLOR SPACE WIDE2, COLOR SPACE...

35
Main Menu (continued)
“GPI CONTROL” is used to enable and disable GPI functions and assign functions to each of the GPI terminal pins
(J  page 48). 
Underlined values indicate factory defaults.
Note: 
This function is not available when,  “SD ASPECT” operation when input signal is HD or PC
 “SCAN” operation when the input signal is PC
 “GAMMA SELECT” operation when the input signal is PC
 “SELECT SYNC” operation when anything other than “RGB-VIDEO” is selected under “YP
BPR/RGB” in the
“INPUT SELECT”...

36
Main Menu (continued)
Underlined values indicate factory defaults.
*1 All five input lines (VIDEO, SDI1, SDI2, YP
BPR/RGB, DVI-D) cannot be turned off. An attempt to turn off all
inputs ends when the fourth input line is turned off since it will not be possible to turn off the 5th input line also. 
*2 “AUTO” is the factory default, but select a specific format when there is risk that the input signal may be contaminated by outside noise.
INPUT SELECT
Sub menu Settings Description
VIDEO OFF
ON
Turns...

37
■COMP. 
Set “RGB-COMP” under “YP
BPR/RGB” in the “INPUT SELECT” menu and select the “RGB-COMP” input line to
enable the “COMP” menu. 
Underlined values indicate factory defaults.
 
*1 Run “AUTOSETUP” when video is displayed across the entire screen area. “EXECUTING” is displayed during“AUTOSETUP” and “COMPLETE” appears when setup completes.  
“INCOMPLETE” is displayed if setup could not be completed. 
AUTOSETUP may not provide adequate adjustment for some video input. Use H POSITION, V POSITION,
PHASE...

38
Use the following submenus to set headphone output and audio level meters. Underlined values indicate factory defaults.
*1 When ANALOG is selected in the “INPUT SELECT” menu, the LEVEL METER does not indicate the audio level meter even when set to ON. 
AU D IO
Sub menu Settings Description
INPUT
SELECT AU TO
ANALOG Selects input line for audio output to headphone terminal.
  When an SDI input line is selected with the [INPUT] button on 
the front panel: embedded audio (SDI terminal)
When input lines...

39
Underlined values indicate factory defaults.
*1 Available during HD-SDI input signals.
*2 Available during VIDEO (NTSC) input. Closed captions appear as bright lines on line 21 when closed caption is set to ON and underscan is also on.
*3 Opens the vector display during SDI signal input.
DISPLAY SETUP
Sub menu Settings Description
TWO
WINDOW
SIZE L/S
M/M
S/L Selects size of split-screen displays. 
 main window LARGE, sub-window SMALL
 main window MEDIUM, sub-window MEDIUM
 main window SMALL,...

40
Main Menu (continued)
■“WFM/VECTOR” 
The “WFM/VECTOR” function enables display of the waveform and vector display. Use “DISPLAY SETUP” in the
main menu to select “WFM” and “VECTOR” display. ( Jpage 39)
Press the button ([FUNCT ION1] to [FUNCTION5] (Jpage 32)) to which the “WFM/VECTOR” function has been
assigned to turn the function on and off. (This assumes that the “WFM/VECTOR” function has been assigned to
any of the [FUNCTION1] to [FUNCTION5] buttons.)
These examples show 16:9 aspect ratio images....