Panasonic Multiport Hub Aw Hb505 Operating Instructions

							-9-
• Changing Switch Settings on Pan/tilt Head 
qRemove the cover from the pan/tilt head.
* Be careful of the Tally Indicator wire.
wShift the mounting direction switches (SW1, SW2) on
the pan/tilt head depending on whether the head is
suspended from the ceiling or mounted on the floor.
They are originally set for suspended installation.ePlace the cover back on the pan/tilt head.
* Be sure not to trap the wires.
• If the pan/tilt head is connected to the control panel
with a cable longer than 300 meters, set the cable
compensation switch on the pan/tilt head to the ON
position in advance.  If the distance between the
pan/tilt head and the control panel is shorter than 300
meters, keep the switch in the original position (OFF).
For details on shifting the switch, refer to the figure
below or the Operating Instructions for Pan/tilt Head.
SW 2 SW 1 SW 3
SW 2 SW 1 DESKTOP
HANGING
Tally Indicator 
						

							-10-
ON
OFF
• Shifting Cable Compensation Switch on Pan/tilt
Head
If the distance from the control panel to the pan/tilt
head is longer than 300 meters, set the cable compen-
sation switch to the ON position by observing the fol-
lowing procedure.
qRemove the controller connection panel from the
pan/tilt head.
* Be careful of the wires.
wShift the cable compensation switch on the inner side
of the controller connection panel of the pan/tilt head to
the ON position.
ePlace the controller connection panel back on the
pan/tilt head. 
						

							-11-
CONNECTION• Before making any connection, switch off all the com-
ponents of the system.
• Use the Control Panel AC Adaptor AW-PS301 (optional)
and Pan/tilt Head AC Adaptor AW-PS300 (optional).
• Use the Pan/tilt Head AW-PH300 and the Color Video
Camera WV-E550 or AW-E560.  (The color Video
Camera WV-E550 cannot used.) To connect the pan/tilt
head to the camera, the Camera Cable AW-CA20T15
(optional) is necessary.
• Locally purchase a DC cable with a nominal cross sec-
tion of 1.25 mm
2or larger that meets the UL specifica-
tions, and connect the Pan/tilt Head AW-PH300 to the
Pan/tilt Head AC Adaptor AW-PS300 with that cable.
The maximum distance between the pan/tilt head and
pan/tilt head AC adapter is 30 m.
• Connect the AC Adapter AW-PS505 to the Multiport
Hub AW-HB505.
• Connect the AC Adaptor AW-PS301 to the Multi Hybrid
Control Panel AW-RP505 and clamp the DC cable of
the AC adapter to the cord clamp on the control panel.
• Connect the Pan/tilt Head AW-PH300 to the Color
Video Camera or WV-E560 with the Camera Cable AW-
CA20T15.
DC Cord Cord Clamper
Control Panel
AC Adaptor
AW-PS301 
						

							-12-
ITEM(AWC) UP(ABC)PAGEDOWN
  (BAR)IRIS
G/L  INVIDEO  OUT
ZOOM/FOCUS
REMOTEVD
VIDEO/RGB VBS/HD
    75ON
OFF
CONTROL
EXT DC INSEE MANUALCAUTION
• Connect the iris control cable of the motor-driven zoom
lens to the camera and the remote (zoom/focus control)
cable to the pan/tilt head.  If the remote (zoom/focus
control) cable of the motor-driven zoom lens is con-
nected to the camera, the lens cannot be controlled.
To Lens Interface ConnectorTo Iris Connector Iris Control Cable Remote (Zoom/Focus
Control) Cable 
						

							-13-
CAMERA
CONTROL OUTCAMERA
CONTROL IN VIDEO OUTPAM/TILT
CONTROL OUTPAM/TILT
CONTROL IN
S-VIDEO OUT VIDEO
IN
G/L
OUTG/L
IN
CAMERA
CONTROL OUTVIDEO OUTPAM/TILT
CONTROL OUT
S-VIDEO OUT VIDEO
IN
G/L
OUT
CAMERA
CONTROL OUTVIDEO OUTPAM/TILT
CONTROL OUT
S-VIDEO OUT VIDEO
IN
G/L
OUT
CAMERA
CONTROL OUTVIDEO OUTPAM/TILT
CONTROL OUT
S-VIDEO OUT VIDEO
IN
G/L
OUT
CAMERA
CONTROL OUTVIDEO OUTPAM/TILT
CONTROL OUT
S-VIDEO OUT VIDEO
IN
G/L
OUT
4
3
2
1 5
DC12V  IN
TO CAMERA PAM/TILT HEAD
TO CONTROL PANELPREVIEW OUT
SEE MANUAL
PAGEITEM(AWC) UP(ABC)DOWN  (BAR)IRIS
G/L  INVIDEO  OUT
ZOOM/FOCUS
REMOTEVD
VIDEO/RGB VBS/HD
    75ON
OFF
CONTROL
EXT DC INSEE MANUALCAUTION
DC+15V
AC IN
LAMP AC OUT
MIN  250W
MAX 500W
OPTION   SW
CONTROL OUTOPTION   SW
CONTROL INLAMP
CONTROL
OP SC
DC 15V
OUT- +
TALLYDC12V IN
AUX  CONTROL  IN1 2 3 4
5 
PREVIEW IN OUT G/L  OUTPREVIEW MONITOR OUT
CONTROL CONTROL  OUTPAN/TILT CAMERA
TD  MULTI  PORT  HUBG / L  IN
• Connect the multiport hub to the multi hybrid control
panel with the three coaxial cables (video signal, G/L
signal, camera control signal)  and one 10BASE-T
straight cable (pan/tilt head control signal).  The maxi-
mum distance between the control panel and pan/tilt
head is 10 meters for coaxial cables 5C-2V and
10BASE-T straight cable (UTP category 5 or equiva-
lent).
• Connect the multiport hub to the multi hybrid control
panel with the three coaxial cables (video signal, G/L
signal, camera control signal)  and one 10BASE-T
straight cable (pan/tilt head control signal).  The maxi-
mum distance between the control panel and each
pan/tilt head is 500 meters for coaxial cables 5C-2V
and 10BASE-T straight cable (UTP category 5 or equiv-
alent).
• For further details on connecting the individual devices,
refer to their operating instruction manuals.
Connecting the Control Panel to Multiport Hub, Color video
Camera (WV-E560), Pan/tilt Head (AW-PH300), and Pan/tilt
Head AC Adapter (AW-PS300)
Pan/tilt Head
AW-PH300Color Video Camera
AW-E560To Servo Control Zoom Lens
Camera Cable
AW-CA20T15
Pan/tilt Head AC Adaptor AW-PS300PREVIEW VIDEO OUT
G/L THROUGH
OUT
G/L IN
PAN/TILT CONTROLZOOM/FOCUS
CONTROL
CAMERA CONTROLGEN-LOCK
VIDEOMulti Hybrid
Control Panel
AW-RP505
Multiport Hub
AW-HB505 IRIS CONTROL 
						

							-14-
S-VIDEO VIDEO
PREVIEW
VIDEO
VIDEO
CONTACT PAN/TILT
CONTROL
PAN/TILT
CONTROL CAMERA CONTROL
CAMERA CONTROL SYSTEM
TALLY
G/L 
G/L  DC-15V
OPTION
SWITCH 
CONTROL
PREVIEW
VIDEO
G/L
ONPOWER
OFFPOWER
O    I
FUSE(POWER)
3.15AFUSEFUSE
Option UnitSEG, Switcher etc.
POWERON
OFF
Color  Monitor  WV-CM   1470
PUSH
POWERON
OFF
Color  Monitor  WV-CM   1470
PUSH
ZOOM/FOCUS CONTROL
IRIS CONTROL
LAMPCONTROL
SPEED FOUCUS PA N  /  T I LT
ZOOMTELE
WIDEFA R
LEFT RIGHTUP
DOWN
NEAR
DEFON
OFF ON
OFF
POWEROPERATE
IRISCAM
CONT
BAR
CAMMODEGAIN AWC
SCENE
FILEABC
AT W
A
B
AUTO/AIWELC LOW MID
MANUON SC H
OFF HIGHT AGC
OFF 1 / 100SHUTTER
ON
OFF
LAMPMEMORY
ON
OFF AUTO
MANUON
OFFON
OFFON
OFF ON
OFFON
OFF
WIP
EXT ND OPH / F
1 .
2 .
3 .
4 .
G/L PHASE
PRESET
T.PEDMulti Hybrid Control Panel AW-RP505
154 3 2 154 3 2
2 1345
67891090¡  180¡
0¡     270¡
LEVELTALLYCONTROL
POWER
1
YC2
YC3
YC4
YC5
YC
OFF ON
CABLE  COMP
Multl  Port  Hub  AW-H8505
POWERON
OFF
Color  Monitor  WV-CM   1470
PUSH
POWERON
OFF
Color  Monitor  WV-CM   1470
PUSH
POWERON
OFF
Color  Monitor  WV-CM   1470
PUSH
POWERON
OFF
Color  Monitor  WV-CM   1470
PUSH
Signal Generator
Control Panel
AC Adaptor
AW-PS301 Pan/tilt Head AC
Adaptor
AW-PS300 Halogen
LampColor Monitor
(75Wterminator) Color Video
Camera
AW-E560
Camera Cable
AW-CA20T15
Multiport Hub
AW-HB505
Preview Color Monitor
(75Wterminator) Servo Control
Zoom Lens
Unnecessary if no
halogen lamp is used. Unnecessary if
no optional unit is
connected.
•Expample of System Connection
Multi Hybrid Control panel AW-RP505
Multiport Hab
AC Adabtor
AW-PS505 
						

							MEMORY
PRESET
2 1345
678910
-15-
OPERATION1. Power
Set the power switches on the pan/tilt head AC adapter
and the multiport hub AC adapter to the ON position,
then set Power control Switch on the multi control panel
to the ON position.
2. Pan/tilt Limiter Setting for Pan/tilt Head
If there are obstacles around the pan/tilt heads, set the
limiters to limit the operating range (pan left and right
ends, tilt up and down ends) of the pan/tilt head.
Note:The switches on the pan/tilt head have been pre-
set before shipment from the factory on the
assumption that the pan/tilt head would be sus-
pended from the ceiling.  If the pan/tilt head is
mounted on a board, for example, be sure to shift
the mounting direction switches on the pan/tilt
head.  Unless this is done, pan/tilt directions will be
reversed and pan/head operation limiter data can-
not be properly stored in the memory.  For details
on shifting these switches, refer to INSTALLATION
OF PAN/TILT HEAD at page 8 or the Operating
Instructions for Pan/tilt Head.qSelect a pan/tilt head with the CONTROL switch on the
multi hybrid control panel.
wLeft Panning Limiter
Turn the pan/tilt head to the desired left panning limit
with PAN/TILT Lever of the multi hybrid control panel,
keep MEMORY Switch depressed, and simultaneously
press buttons [1] and [6] of PRESET Switch for 5 sec-
onds or more.  When the desired limit has been set,
button [5] of PRESET Switch lights.
To reset the limit, keep the MEMORY switch
depressed, and simultaneously press buttons [1] and
[6] of PRESET Switch again for 5 seconds or more.
When the set limit is reset, button [10] of PRESET
Switch lights.
Up tilting limiterPreset position selection switch
Left panning
limiter
Preset
memory
switchRight panning 
limiterLights on 
completion 
of resetting
Down titing
limitorLights on 
completion 
of setting 
						

							-16-
eRight Panning Limiter
Turn the pan/tilt head to the desired right panning limit
with PAN/TILT Lever of the multi hybrid control panel,
keep MEMORY Switch depressed, and simultaneously
press buttons [4] and [9] of PRESET Switch for 5 sec-
onds or more.  When the desired limit has been set,
button [5] of PRESET Switch lights.
To reset the limit, keep the MEMORY Switch
depressed, and simultaneously press buttons [4] and
[9] of PRESET Switch again for 5 seconds or more.
When the set limit is reset, button [10] of PRESET
Switch lights.
rUp Tilting Limiter
Turn the pan/tilt head to the desired up tilting limit with
PAN/TILT Lever of the multi hybrid control panel, keep
MEMORY Switch depressed, and simultaneously press
buttons [2] and [3] of PRESET Switch for 5 seconds or
more.  When the desired limit has been set, button [5]
of PRESET Switch lights.
To reset the limit, keep the MEMORY switch
depressed, and simultaneously press buttons [2] and
[3] of PRESET Switch again for 5 seconds or more.
When the set limit is reset, button [10] of PRESET
Switch lights.
tDown Tilting Limiter
Turn the pan/tilt head to the desired down tilting limit
with PAN/TILT Lever of the multi hybrid control panel,
keep MEMORY Switch depressed, and simultaneously
press buttons [7] and [8] of PRESET Switch for 5 sec-onds or more.  When the desired limit has been set,
button [5] of PRESET Switch lights.
To reset the limit, keep the MEMORY switch
depressed, and simultaneously press buttons [7] and
[8] of PRESET Switch again for 5 seconds or more.
When the set limit is reset, button [10] of PRESET
Switch lights.
ySelect a pan/tilt head with the CONTROL switch on the
multi hybrid control panel, and set the its operating
range limiters.  Repeat the same process for each of
the other pan/tilt heads.
3. Cable Compensation Setting, Genlock and
Total Pedestal Adjustment1) After selecting a camera with the CONTROL switch on
the multi hybrid control panel, set the CAM CONT
switch to the ON position.
Note:When the CAM CONT switch on the multi hybrid
control panel is set to the ON position, the switch
settings of the multi hybrid control panel are sent
to the camera to update its settings.  Do not set
the CAM CONT switch to the ON position except
when changing the camera settings.  If another
camera is selected with the CONTROL switch
while the CAM CONT switch is in the ON position,
the settings of the selected camera will be similarly
changed.  Set the CAM CONT switch back to the
OFF position before changing one camera for
another with the CONTROL switch. 
						

							-17-
2) Adjust the cable compensation, genlock, and total
pedestal of the selected camera.
• Cable Compensation
Signal degradation due to cable length between the con-
trol panel and the pan/tilt head can be compensated for.
qIf the cable length from the pan/tilt head to the control
panel is longer than 300 meters, set the cable com-
pensation switch on the pan/tilt head to the ON posi-
tion.  For details, refer to INSTALLATION OF PAN/TILT
HEAD at page 8 or the Operating Instructions for
Pan/tilt Head.
wConnect a waveform monitor or a vectorscope to the
video output connector on the control panel for the
corresponding the camera pan/tilt head number ([1] to
[5]), set the video output connector on the control
panel, set the mode switch to the BAR position, then
observe the color bar signals.
eAdjust the Y (luminance) signal level with the CABLE
COMP Y control for the corresponding camera pan/tilt
head number ([1] to [5]), then adjust the CABLE
COMP Y control then adjust the C (chrominance) sig-
nal level with CABLE COMP C control. Repeat this until
the video output of the control panel is adjusted as
shown in the figure below.
Note:Turning CABLE COMP Y control changes not
only the Y (luminance) signal level but also the
video signal levels as a whole.
POWER
1
YC2
YC3
YC4
YC5
YC
OFF ON
CABLE  COMP
Multl  Port  Hub  AW-H8505
Waveform Monitor
Vector ScopeColor Monitor
(75Wtermination)
CABLE COMP C Control  CABLE COMP Y Control 
Multiport Hub
AW-HB505 
						

							-18-
GRAY
YELLOW
CYAN
GREEN
MAGENTA
RED
BLUE
100
  90
  80
  70
  60
  50
  40
  30
  20
  10
    0
 -10
 -20
 -30
 -40+69 +77
+56
+48
+38
+12
+7
-5
-16 -16+15 +28 +36
+20
-20 +20
-20+100+100
+89
+77
+72
+46 IRE
75%
100%
1V[p-p]
+100
+27
+27
-20
-13 -13
100
  90
  80
  70
  60
  50
  40
  30
  20
  10
    0
 -10
 -20
 -30
 -40IRE
75%
100%
+20
-20+20
-20 +7.5 +7.5
- I  WHITE  +Q       BLACK
1V[p-p]
Color Monitor
Color MonitorWaveform Monitor
Waveform Monitor
• Genlock AdjustmentTo use the camera in external sync mode, phase adjust-
ment is necessary to match the phases with those of the
other units and camera.  No G/L adjustment is necessary in
case of no genlock.
• Horizontal Phase Adjustment
qSet G/L PHASE ON/OFF Switch of the multi hybrid con-
trol panel to the ON position.
Note:When G/L PHASE ON/OFF Switch of the multi
hybrid control panel is set to the ON position, the
sync phase of the camera changes to the settings
of G/L PHASE H Control, G/L PHASE Coarse
Switch, and G/L PHASE SC Control.  Unless G/L
phase adjustment is necessary, do not set G/L
PHASE ON/OFF Switch to the ON position.
wObserve the waveforms of the G/L signal input (black
burst signal ) and video signal output on a dual chan-
nel oscilloscope, and turn the G/L horizontal phase
control to match the horizontal phase as shown in the
next page.