Panasonic Projector PT-DS12KU User Manual

							Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 121
[SUB VERSION]Displays the sub version of the firmware of the projector.
[NETWORK VERSION] Displays the firmware version of the projector.
[UPGRADE(ET
-

UK20)] Displays the activation status based on the Upgrade Kit.
[ON COUNT] [POWER ON TIMES]
Displays the number of times the power is turned on.
[LAMP1 ON] Displays the number of times the lamp is turned on.
[LAMP2 ON]
[LAMP1] Displays runtime in detail.
[LAMP2] Displays runtime in detail.
[NUMBER OF REGISTERED  SIGNAL] Displays the number of registered signals.
[REMOTE2 STATUS] Displays the control status of the REMOTE2.
[AC VOLTAGE] Displays the status of the AC voltage.
[COOLING CONDITION] Displays the set cooling conditions. When [AUTO] is set, automatically recognized result is displayed.
[SIGNAL INFORMATION] [MEMORY NO.]
Displays the memory number of the input signal.
[INPUT] Displays the input terminal currently selected.
[SIGNAL NAME] Displays the input signal name.
[SIGNAL FREQUENCY] Displays the frequency of the input signal.
[SYNC.STATE] Displays the synch polarity of the input signal.
[V.SYNC WIDTH] Displays the vertical sync signal pulse width of the input signal.
[SCAN TYPE] Displays the scan type of the input signal.
[TOTAL DOTS] Displays the total dot count of the input signal.
[DISPLAY DOTS] Displays the number of input signal display dots.
[TOTAL LINES] Displays the total line count of the input signal.
[DISPLAY LINES] Displays the number of input signal display lines.
[SAMPLING] Displays the sampling information of the input signal.
[SIGNAL LEVEL] Displays the signal level of the input signal.
[BIT DEPTH] Displays the gradation of the input signal.
*1 The lamp runtime to be displayed is real time.  The following conversion is required to calculate the rough estimate for lamp replacement.
Model No.Formula for lamp replacement time (rough estimate)
PT
-

DZ13KU
PT
-

DS12KU
PT
-

DW11KU (A x 56 + B x 40 + C x 35) ÷ 56
 f
A

: Runtime when [LAMP POWER] is set to [HIGH]
 fB

: Runtime when [LAMP POWER] is set to [MIDDLE]
 fC

: Runtime when [LAMP POWER] is set to [ECO]
The formula when the optional Replacement lamp unit (for portrait mode) is used is:
(B x 2 + C) ÷ 2
PT
-

DZ10KU (A x 40 + B x 35) ÷ 40
 f
A

: Runtime when [LAMP POWER] is set to [NORMAL]
 fB

: Runtime when [LAMP POWER] is set to [ECO]
The formula when the optional Replacement lamp unit (for portrait mode) is used is:
(A x 2 + B) ÷ 2
Note
 f The content of status can be sent via E-mail by pressing the  button while displaying the status. fSome items in [SIGNAL
 INFORMATION] may be displayed and others not displayed, depending on the signal being input.
 fIf you attach a lamp unit used in a projector of a model dif

ferent from the projector (PT
-
 DZ13KU, PT
-
 DS12KU, PT
-
 DW11KU, PT
-
 DZ10KU) 
to the projector, or when the lamp unit used in the projector to a projector of a different model, the “lighting time” and “runtime” displayed in 
[STATUS] may differ from the actual time.
[NO SIGNAL SHUT-OFF]
A function that automatically switches the power source of the projector to standby if there is no input signal for a certain period of time. The 
time before switching to standby can be set.
1) Press  as to select [NO SIGNAL SHUT-OFF].
2)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[DISABLE] Disables the No signal shut-off function.
[10MIN.] - [90MIN.] Allows you to set in ten minutes intervals.   
						

							Chapter 4 Settings — [PROJECTOR SETUP] menu
122 - ENGLISH
[REMOTE2 MODE]
You can set the  terminal.
1) Press as to select [REMOTE2 MODE].
2)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[DEFAULT] The pin assignment of the  terminal is used by the factory default setting of the 
projector.
[USER] Used to change the setting of the  terminal.
[L6500 SERIES] The setting of  terminal is used for the L6500 series compatibility .
 fWhen [USER] is selected, proceed to Step  3)

.
3) Press the  button.
4)  
Press 
 as to select one from [PIN2] to [PIN8], and press  qw to switch the setting.
[FUNCTION BUTTON]
Set the functions of the  button on the remote control.
1) Press as to select [FUNCTION BUTTON].
2)  
Press the  button.
 f The  [FUNCTION BUTTON] screen is displayed.
3) Press  as to select a function.
[DISABLE] Disables the  button.
[P IN P] Switches [OFF]/[USER1]/[USER2]/[USER3] in [P IN P]. ( x
  page   127)
[SUB MEMORY] Displays the sub memory list. ( x
  page   132)
[SYSTEM SELECTOR] Switches the [SYSTEM SELECTOR] setting. (x
  page   77)
[SYSTEM DAYLIGHT VIEW] Switches the [SYSTEM DAYLIGHT VIEW] setting. ( x
  page   75)
[FREEZE] Temporarily pauses the image. ( x
  page   106)
[WAVEFORM MONITOR] Displays the waveform of the input signal. ( x
  page   106)
[LENS MEMORY LOAD] Calls the registered lens memory. (x
  page   123)
[LEFT/RIGHT SWAP]
*1Switches the flip horizontal settings. ( x   page   93)
*1 Only for PT-DZ13KU, PT- DS12KU, PT- DW11KU
4) Press the  button.
[DATE AND TIME]
Set the time zone, date, and time of the built-in clock of the projector .
Setting the time zone
1) Press as to select [DATE AND TIME].
2)  
Press the  button.
 f The  [DATE AND TIME] screen is displayed.
3) Press  as to select [TIME ZONE].
4)  
Press 
 qw to switch [TIME ZONE].
Setting the date and time manually
1) Press as to select [DATE AND TIME].
2)  
Press the  button.
 f The  [DATE AND TIME] screen is displayed.
3) Press  as to select [ADJUST CLOCK].   
						

							Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 123
4) Press the  button.
 fThe  [ADJUST CLOCK] screen is displayed.
5) Press  as to select an item, and press qw to set the local date and time.
6)  
Press 
 as to select [APPLY], and press the  button.
 fThe setting of the date and time will be completed.
Setting the date and time automatically
1) Press  as to select [DATE AND TIME].
2)  
Press the  button.
 f The  [DATE AND TIME] screen is displayed.
3) Press  as to select [ADJUST CLOCK].
4)  
Press the  button.
 f The  [ADJUST CLOCK] screen is displayed.
5) Press  as to select [NTP SYNCHRONIZATION], and press qw to change the setting to [ON].
6)  
Press 
 as to select [APPLY], and press the  button.
 fThe setting of the date and time will be completed.
Note
 fTo set the date and time automatically, the projector must be connected to the network. fIf synchronization with the NTP
 server fails just after [NTP SYNCHRONIZATION] is turned [ON], or if [NTP SYNCHRONIZATION] is turned 
[ON] while the NTP server is not set, [NTP SYNCHRONIZATION] will return to [OFF].
 f Access the projector via a web browser to set the NTP

 server. Refer to “[Adjust clock] page” (x   page   147) for details.
[LENS CALIBRATION]
Automatically set the lens shift limit values and home position for the projector.
1) Press as to select [LENS CALIBRATION].
2)  
Press the  button.
 f The confirmation screen is displayed.
3) Press  qw to select [OK], and press the  button.
 fTo cancel, select [CANCEL].
 fThe lens moves up, down, left, and right to automatically set the lens shift limit values and home position.
 fThe lens stops to complete the calibration.
Note
 f[PROGRESS] is displayed on the menu during lens calibration. Cannot cancel mid-operation. fWhen lens calibration executes correctly
, [COMPLETE] is displayed and [INCOMPLETE] is displayed when it does not execute correctly .
 fPressing the  button on the remote control for at least three seconds will also display the confirmation screen for lens calibration 
execution.
[LENS MEMORY]
Save and load the focus position, shift position, and zoom position of an adjusted lens.
Saving lens position
1) Press  as to select [LENS MEMORY].
2)  
Press the  button.
3)

 
Press 
 as to select [LENS MEMORY SAVE].
4)
 
Press the  button.
 f The  [LENS MEMORY SAVE] screen is displayed.
5) Press  as to select the item to save, and press the  button.   
						

							Chapter 4 Settings — [PROJECTOR SETUP] menu
124 - ENGLISH
6) When the confirmation screen is displayed, press qw  to select [OK], and press the  button.
 fThe  [LENS MEMORY NAME INPUT] screen is displayed.
7) Press  asqw to select the text, and press the  button to enter the text.
8)  
After the name is input, press  asqw to select [OK], and press the  button.
 fThe registration completes and returns to the  [LENS MEMOR Y SAVE] screen.
 fIf you press 

asqw to select [CANCEL] and then press the  button, the lens memory will not be saved.
 fIf you press 

asqw to select [DEFAULT] and press the  button, the entered name will not be registered and the default 
name will be used.
 f If you select [OK] without entering any characters and press the  button, the default name will be used.
Loading the lens position
1) Press  as to select [LENS MEMORY].
2)  
Press the  button.
3)

 
Press 
 as to select [LENS MEMORY LOAD].
4)
 
Press the  button.
 f The  [LENS MEMORY LOAD] screen is displayed.
5) Press  as to select the item to load, and press the  button.
6)  
When the confirmation screen is displayed, press  qw

 to select [OK], and press the  button.
 fThe lens moves automatically to the registered shift, zoom, and focus positions.
Note
 fLens memory is not guaranteed to be 100   % reproduced. fThe zoom and focus positions may have shifted after lens memory was loaded. Readjust as necessary . fBeware of shift, as errors in zoom position are particularly significant. fWhen a lens is replaced, readjust and save the lens memory again. fIf a lens without zoom function is used, the lens memory of the zoom position does not operate. fWhen [LENS MEMOR

Y LOAD] is assigned to the  button, the lens memory is loaded in order each time you press the  
button.
Deleting a lens memory
1) Press  as to select [LENS MEMORY].
2)  
Press the  button.
3)

 
Press 
 as to select [LENS MEMORY EDIT].
4)
 
Press the  button.
 f The  [LENS MEMORY EDIT] screen is displayed.
5) Press  as to select [LENS MEMORY DELETE].
6)  
Press the  button.
 f The  [LENS MEMORY DELETE] screen is displayed.
7) Press  as to select the item to delete, and press the  button.
8)  
When the confirmation screen is displayed, press  qw

 to select [OK], and press the  button.
Changing the lens memory name
1) Press as to select [LENS MEMORY].
2)  
Press the  button.
3)

 
Press 
 as to select [LENS MEMORY EDIT].
4)
 
Press the  button.
 f The  [LENS MEMORY EDIT] screen is displayed.   
						

							Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 125
5) Press as to select [LENS MEMORY NAME CHANGE].
6)  
Press the  button.
 f The  [LENS MEMORY NAME CHANGE] screen is displayed.
7) Press  as to select the name to change, and press the  button.
 fThe  [LENS MEMORY NAME INPUT] screen is displayed.
8) Press  asqw to select the text, and press the  button to enter the text.
9)  
After the name is changed, press 
 asqw to select [OK], and press the  button.
 fThe registration completes and returns to the  [LENS MEMOR Y NAME CHANGE] screen.
 fIf you press 

asqw to select [CANCEL] and then press the  button, the changed name will not be registered.
 fIf you press 

asqw to select [DEFAULT] and press the  button, the changed name will not be registered and the default 
name will be used.
 f If you select [OK] without entering any characters and press the  button, the default name will be used.
[SAVE ALL USER DATA]
Save the various setting values as a backup in the built-in memory of the projector .
1) Press as to select [SAVE ALL USER DATA].
2)  
Press the  button.
 f The  [SECURITY PASSWORD] screen is displayed.
3) Enter a security password and press the  button.
4)  
When the confirmation screen is displayed, press  qw

 to select [OK], and press the  button.
 f[PROGRESS] is displayed while saving data.
[LOAD ALL USER DATA]
Load the various setting values saved as a backup in the built-in memory of the projector .
1) Press as to select [LOAD ALL USER DATA].
2)  
Press the  button.
 f The  [SECURITY PASSWORD] screen is displayed.
3) Enter a security password and press the  button.
4)  
When the confirmation screen is displayed, press  qw

 to select [OK], and press the  button.
Note
 f The projector will go into the standby status to reflect the setting values when [LOAD  ALL  USER DATA] is executed. fData registered from a computer is not included in [ALL
 USER DATA].
[INITIALIZE]
Return various setting values to their factory default settings.
1) Press as to select [INITIALIZE].
2)  
Press the  button.
 f The  [SECURITY PASSWORD] screen is displayed.
3) Enter a security password and press the  button.
 fThe  [INITIALIZE]  screen is displayed.
4) Press as to select an item to initialize.
[ALL USER DATA] Returns all setting items including [REGISTERED SIGNAL], [NETWORK SETUP], [E-mail set up], 
and [USER LOGO] to factory default settings.
The projector will go into the standby status to reflect the setting values.
[REGISTERED SIGNAL] Deletes all the setting values saved for each input signal.
To delete only a part of a registered signal, perform the procedure described in “Deleting the 
registered signal” (
x
  page   130).
[NETWORK/E-MAIL] Returns [NETWORK SETUP] and [E-mail set up] to factory default settings.
[LOGO IMAGE] Deletes the image registered in [USER LOGO].   
						

							Chapter 4 Settings — [PROJECTOR SETUP] menu
126 - ENGLISH
5) Press the  button.
6)  
When the confirmation screen is displayed, press  qw

 to select [OK], and press the  button.
[SERVICE PASSWORD]
This function is used by a service person.   
						

							Chapter 4 Settings — [P IN P] menu
ENGLISH - 127
[P IN P] menu
On the menu screen, select [P IN P] from the main menu, and select an item from the sub-
menu.
Refer to “Navigating through the menu” (x
  page   65) for the operation of the menu screen.
 fAfter selecting the item, press 

asqw to set.
Using P IN P function
Locate a separate, small sub screen in the main screen to project two images simultaneously .
1) Press as to select [P IN P MODE].
2)  
Press the  button.
 f The  [P IN P MODE] screen is displayed.
3) Press  as to select a function.
[OFF] P IN P function is not used.
[USER1]
The items set in “Setting P IN P function” (x
  page   127) are used in P IN P function.
[USER2]
[USER3]
4) Press the  button.
Setting P IN P function
P IN P function settings can be saved to [USER1], [USER2], and [USER3].
1) Press 
as to select [P IN P MODE].
2)  
Press the  button.
 f The  [P IN P MODE] screen is displayed.
3) Press  as to select the desired mode from [USER1], [USER2], and [USER3], and pres\
s the  
button.
4)
 
Press 
 as to select [MAIN WINDOW] or [SUB WINDOW], and press the  button.
5)
 
Press 
 as to select the input terminal to be displayed in the window, and press the  button.
6)
 
Press 
 asto select an item.
[SIZE] Set the window display size between 10   % and 100   %.
[POSITION] Set the display position of the window within the screen.
[CLOCK PHASE] When the sub window is input from the  terminal or the  terminal and a 
flickering image or smeared outline appears, set between 0 and +31.
7) If [SIZE] is selected in Step 6), press the  button.
 f
The sub-menu is displayed.
8) Press  asto select an item.
9)  
Press 
 qw to make adjustment, and press the  button.
10)
 
If [POSITION] is selected in Step 6), press the  button.
1

1)  
Press 
 asqw to adjust the position, and press the  button.   
						

							Chapter 4 Settings — [P IN P] menu
128 - ENGLISH
12) If [CLOCK PHASE] is selected in Step 6), press qw  to make adjustment.
13)  
Press 
 as to select [FRAME LOCK].
14)
 
Press 
 qw to switch the item.
[MAIN WINDOW] Set frame lock to the input signal set in the main window.
[SUB WINDOW] Set frame lock to the input signal set in the sub window.
15) Press as to select [TYPE].
16)  
Press 
 qw to switch the item.
[MAIN WINDOW] The main window has display priority.
[SUB WINDOW] The sub window has display priority.
Note
 fThe P IN P function may not be available for some signals being input or terminals being selected. Refer to “Two-window display 
combination list” ( x
  page   178) for details.
 fThe main window setting values are applied to image adjustment values such as [PICTURE MODE], [GAMMA], and [COLOR 
TEMPERA

TURE].
 fOn the main screen (when no menu is displayed), press  qw

 to switch the sizes and positions of the main window and sub window while P  
IN P is operating.
 f When [FRAME RESPONSE] is set to other than [NORMAL], [P

 IN P] cannot be set.
 fWhen [BACKUP

 INPUT MODE] is set to [ON], [1], or [2], [P IN P] cannot be set.
 f3D images cannot be displayed in P

 IN P. (Only for PT
-
 DZ13KU, PT
-
 DS12KU, PT
-
 DW11KU)
 fThe P

 IN P state continues while the P IN P function is used, even if 3D images of the simultaneous system are displayed. (Only for 
PT
-

DZ13KU, PT
-
 DS12KU, PT
-
 DW11KU)   
						

							Chapter 4 Settings — [TEST PATTERN] menu
ENGLISH - 129
[TEST PATTERN] menu
On the menu screen, select [TEST PATTERN] from the main menu.
Refer to “Navigating through the menu” (x
  page   65) for the operation of the menu screen.
 fPress 

qw to switch.
[TEST PATTERN]
Display the test pattern built-in to the projector.
Settings of position, size, and other factors will not be reflected in test patterns. Make sure to display the input signal before performing various 
adjustments.
1) Press  qw to switch the [TEST PATTERN] item.
 fThe items will switch each time you press the button.
Menu screen + All white
Displays test patterns with the menu screen. Select a test pattern so that it is easy to make various 
adjustments.
Menu screen + All black
Menu screen + Window
Menu screen + Window  (inversion)
Menu screen + Color bar  (vertical)
Menu screen + Color bar  (horizontal)
Menu screen + 16:9/4:3  aspect frame
Menu screen + Focus
Menu screen + Entry screen Displays the menu screen and input signal.
Built-in test patterns are not displayed.
Note
 f
Press the  button on the remote control while the test pattern is displayed to hide the menu screen.
Changing color or a focus test pattern
When the “Menu Screen + Focus” test pattern is displayed, the color can be changed.
1) Press  qw to select the “Menu Screen + Focus” test pattern.
2)  
Press the  button.
 f The  [TEST PATTERN COLOR] screen is displayed.
3) Press  as to select a color, and press the  button.
 fThe test pattern color changed to the color selected.
Note
 fThe test pattern color settings return to [WHITE] when the projector is switched of f. fColors of the test patterns other than focus test patterns cannot be changed.   
						

							Chapter 4 Settings — [SIGNAL LIST] menu
130 - ENGLISH
[SIGNAL LIST] menu
On the menu screen, select [SIGNAL LIST] from the main menu.
Refer to “Navigating through the menu” (x
  page   65) for the operation of the menu screen.
 rRegistered signal details
A1 (1-2)
When the address number (A1, A2, ... L7, L8) signal is registered Sub memory number
Memory number:
 f
A name can be set for each sub memory (x   page   132).
Registering new signals
After a new signal is input and the  button on the remote control or the control panel is pressed, the registration is completed and the 
[MAIN MENU] screen is displayed.
Note
 fUp to 96 signals, including sub memories, can be registered to the projector . fThere are 12 pages (eight memories of 
A through L, with eight memories possible on each page) for memory numbers, and the signal is 
registered to the lowest number that is available. If there is no available memory number it will be overwritten from the oldest signal.
 f The names to be registered are automatically determined by the input signals and memory numbers. fIf a menu is being displayed, the new signals will be registered at the instant they are input.
Renaming the registered signal
Registered signals can be renamed.
1) Press  asqw to select the signal of which name is to be changed.
2)  
Press the  button.
 f The  [REGISTERED SIGNAL STATUS] screen is displayed.
 fThe memory number

, input terminal, input signal name, frequency, synch polarity, etc., are displayed.
 fPress the  button to return to the 

[SIGNAL LIST] screen.
3) Press the  button.
 fThe  [REGISTERED SIGNAL SETUP] screen is displayed.
4) Press  as to select [SIGNAL NAME CHANGE].
5)  
Press the  button.
 f The  [SIGNAL NAME CHANGE] screen is displayed.
6) Press  asqw to select the text, and press the  button to enter the text.
7)  
After the name is changed, press 
 asqw to select [OK], and press the  button.
 fThe registration is completed and the  [REGISTERED SIGNAL  SETUP] screen returns.
 fWhen pressing  asqw to select [CANCEL] and pressing the  button, the changed signal name will not be registered and 
an automatically registered signal name will be used.
Deleting the registered signal
Registered signals can be deleted.
1) Press  asqw to select the signal to delete.
2)  
Press the  button.
 fThe  [REGISTERED SIGNAL DELETE] screen is displayed.