Panasonic Projector PT-DS12KU User Manual

							Chapter 4 Settings — [SIGNAL LIST] menu
ENGLISH - 131
 fTo cancel the deletion, press the  button to return to the  [REGISTERED SIGNAL LIST] screen.
3) Press the  button.
 fThe selected signal will be deleted.
Note
 fA registered signal can also be deleted from [REGISTERED SIGNAL DELETE] on the [REGISTERED SIGNAL SETUP] screen.
Protecting the registered signal
1) Press  asqw to select the signal to protect.
2)  
Press the  button.
 f The  [REGISTERED SIGNAL STATUS] screen is displayed.
3) Press the  button.
 fThe  [REGISTERED SIGNAL SETUP] screen is displayed.
4) Press  as to select [LOCK].
5)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] The signal is not protected.
[ON] The signal is protected.
Note
 fWhen [LOCK] is set to [ON], signal deletion, image adjustment, and automatic setup are not available.  T o perform these operations, set 
[LOCK] to [OFF].
 f A

 signal can be registered to the sub memory even if it is protected.
 fEven a protected signal will be deleted if [INITIALIZE] is executed.
Expanding signal lock-in range
1) Press  asqw to select the signal to set.
2)  
Press the  button.
 f The  [REGISTERED SIGNAL STATUS] screen is displayed.
3) Press the  button.
 fThe  [REGISTERED SIGNAL SETUP] screen is displayed.
4) Press  as to select [LOCK-IN RANGE].
5)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[NARROW] Select in most cases.
[WIDE] Widens the lock-in range.
Note
 fSwitch the range that determines that a signal to be input is the same signal that is already registered. fT
o prioritize the determination that it is the same signal that is already registered, set to the [WIDE] setting.
 f Use in cases such as when the synchronizing frequency of a signal to be input has changed slightly , or multiple signal lists are registered. fCan only be used when a signal is input from the  terminal,  terminal,  terminal, or  terminal. fWhen [WIDE] is set, the image may appear distorted because a signal is determined to be the same signal even if a synchronizing 
frequency changes slightly

.
 fWhen a signal to be input corresponds to multiple signals set in [WIDE], a registered signal with a high memory number receives priority . 
Example: a signal to be input that corresponds to memory numbers  A2, 

A4 and B1 will be determined to be B1.
 fWhen a registration signal is deleted, the settings are also deleted. fIn an environment where multiple types of signals are input to the same terminal, signals are sometimes not determined correctly when the 
setting is set to [WIDE].   
						

							Chapter 4 Settings — [SIGNAL LIST] menu
132 - ENGLISH
Sub memory
The projector has a sub memory function that can register the multiple image adjustment data, even if it is recognized as the same signal by 
the frequency or format of the synchronization signal source.
Use this function when you need to adjust the picture quality such as switching of the aspect ratio or white balance by the same 
synchronization signal source. The sub memory includes all the data that can be adjusted for each signal, such as the screen aspect ratio and 
data adjusted in the [PICTURE] item ([CONTRAST], [BRIGHTNESS], etc.).
Registering to the sub memory
1) Press qw on the normal screen (when the menu is not displayed).
 fThe sub memory registration screen is displayed if the sub memory is not registered. Proceed to Step  3) .
 fA

 list of sub memories registered to the signal currently input is displayed.
 fBy selecting [SUB MEMOR

Y] in the [PROJECTOR SETUP] menu → [FUNCTION BUTTON], the  button can be used instead 
of qw.
2) Press  asqw to select the sub memory number to register in [SUB MEMORY LIST].
3)  
Press the  button.
 f The  [SIGNAL NAME CHANGE] screen is displayed.
4) Press  asqw to select [OK], and press the  button.
 fTo rename the registered signal, follow the procedure in Steps  6) and 7) in “Renaming the registered signal” (x   page   130).
Switching to the sub memory
1) Press qw on the normal screen (when the menu is not displayed).
 fA list of sub memories registered to the signal currently input is displayed.
2) Press  asqw to select the signal to switch in [SUB MEMORY LIST].
3)  
Press the  button.
 f This switches to the signal selected in Step  2) .
Deleting the sub memory
1) Press qw on the normal screen (when the menu is not displayed).
 fThe  [SUB MEMORY LIST]  screen is displayed.
2) Press asqw to select the sub memory to delete, and press the  button.
 fThe  [REGISTERED SIGNAL DELETE] screen is displayed.
 fT

o cancel the deletion, press the  button to return to the  [SUB MEMORY LIST] screen.
3) Press the  button.
 fThe selected sub memory will be deleted.   
						

							Chapter 4 Settings — [SECURITY] menu
ENGLISH - 133
[SECURITY] menu
On the menu screen, select [SECURITY] from the main menu, and select an \
item from the sub-
menu.
Refer to “Navigating through the menu” (x
  page   65) for the operation of the menu screen.
 fWhen the projector is used for the first time
Initial password: Press  awsqawsq in order

, and press the  button.
 fAfter selecting the item, press 

asqw to set.
Attention
 fWhen you select the [SECURITY] menu and press the  button, entering a password is required. Enter the preset password and 
then continue operations of the [SECURITY] menu.
 fWhen the password has been changed previously

, enter the changed password, and press the  button.
Note
 fThe entered password is displayed with*marks on the screen. fAn error message is displayed on the screen when the entered password is incorrect. Re-enter the correct password.
[SECURITY PASSWORD]
Display the  [SECURITY PASSWORD] screen when the power is turned on with the  switch set to the  side. When 
the entered password is incorrect, the operation will be restricted to the power standby < v> button, the  button, and the  
(, , ) buttons.
1) Press  as to select [SECURITY PASSWORD].
2)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Disables the security password entry.
[ON] Enables the security password entry.
Note
 fThe [SECURITY  PASSWORD] setting is set to [OFF] by the factory default or when [ALL USER DATA] in [INITIALIZE] ( x   page   125) is 
executed.
 f Change the password periodically that is hard to guess. fThe security password is enabled after setting [SECURITY

 PASSWORD] to [ON] and turning the  switch to .
[SECURITY PASSWORD CHANGE]
Change the security password.
1) Press as to select [SECURITY PASSWORD CHANGE].
2)  
Press the  button.
 f The  [SECURITY PASSWORD CHANGE] screen is displayed.
3) Press  asqw and the number ( - ) buttons to set the password.
 fUp to eight button operations can be set.
4) Press the  button.
5)  
Re-enter the password for the confirmation.
6)

 
Press the  button.
Note
 f The entered password is displayed with*marks on the screen.   
						

							Chapter 4 Settings — [SECURITY] menu
134 - ENGLISH
 fWhen numerical values are used for the security password, the security password is required to be initialized if the remote control is lost. 
Consult your dealer for the method of initialization.
[DISPLAY SETTING]
Overlap the security message (text or image) over the projecting image.
1) Press  as to select [DISPLAY SETTING].
2)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] The text display is disabled.
[TEXT] The text display is enabled.
[USER LOGO] Displays the image registered by the user.
Note
 fTo create/register the [USER LOGO] image, use “Logo Transfer Software” included in the supplied CD-ROM.
[TEXT CHANGE]
Change the text displayed when the text display is enabled by selecting [TEXT] in [DISPLA Y SETTING].
1) Press as to select [TEXT CHANGE].
2)  
Press the  button.
 f The  [TEXT CHANGE] screen is displayed.
3) Press  asqw to select the text, and press the  button to enter the text.
4)  
Press 
 asqw to select [OK], and press the  button.
 fThe text is changed.
[CONTROL DEVICE SETUP]
Enable/disable the button operations on the control panel and the remote control.
1) Press  as to select [CONTROL DEVICE SETUP].
2)  
Press the  button.
 f The  [CONTROL DEVICE SETUP] screen is displayed.
3) Press  as to select [CONTROL PANEL] or [REMOTE CONTROL].
[CONTROL PANEL] You can set the limitation on the control from the control panel.
[REMOTE CONTROL] You can set the limitation on the control from the remote control.
4) Press the  button.
 fThe  [CONTROL PANEL] screen or the [REMOTE CONTROL] screen is displayed.
5) Press  as to select [CONTROL PANEL] or [REMOTE CONTROL].
6)  
Press 
 qw to switch the item.
 fYou can set the operation restriction from the control panel or the remote control.
[ENABLE] Enables all button operations.
[DISABLE] Disables all button operations.
[USER] Operation of all buttons can be enabled/disabled separately.
Refer to “Enabling/disabling any button” (
x
  page   134) for details.
7) Press as to select [APPLY], and press the  button.
 fThe confirmation screen is displayed.
8) Press  qw to select [OK], and press the  button.
Enabling/disabling any button
1) Press as to select [CONTROL DEVICE SETUP].   
						

							Chapter 4 Settings — [SECURITY] menu
ENGLISH - 135
2) Press the  button.
 fThe  [CONTROL DEVICE SETUP] screen is displayed.
3) Press  as to select [CONTROL PANEL] or [REMOTE CONTROL].
4)  
Press the  button.
5)

 
Press 
 as to select [CONTROL PANEL] or [REMOTE CONTROL].
6)
 
Press 
 qw to switch [USER].
7)
 
Press 
 as to select the button item to set.
 fWhen [INPUT  SELECT BUTTON] is selected, press the  button, and then press as to select the button to set.
Buttons that can be set
[CONTROL PANEL] [REMOTE CONTROL]
[POWER BUTTON] Power standby  button, power on  button
[INPUT SELECT BUTTON]  button,  button,  button,  button,  button, and  
button
*1
[MENU BUTTON]
 button
[LENS BUTTON]  button  button,  button,  
button
[AUTO SETUP BUTTON]  button
[SHUTTER BUTTON]  button
[ASPECT BUTTON] — button
[ON SCREEN BUTTON] — button
[OTHER BUTTON] asqw,  button Buttons not listed above
*1 Only for PT-
DZ13KU, PT- DS12KU, PT- DZ10KU
8) Press qw to switch the item.
[ENABLE] Enables button operations.
[DISABLE] Disables button operations.
 fThe following items are available when [SDI1/2 BUTT

ON] is selected in [INPUT SELECT BUTTON] in PT
-
 DZ13KU and PT
-
 DS12KU.
[TOGGLE]Switches between SDI1 and SDI2 when the button is operated.
[SDI1] Fixes to SDI1.
[SDI2] Fixes to SDI2.
[DISABLE] Disables button operations.
 fWhen [INPUT

 SELECT BUTTON] is selected in Step 7), press the  button to return to the [CONTROL PANEL] screen or the 
[REMOTE CONTROL] screen.
9) Press  as to select [APPLY], and press the  button.
 fThe confirmation screen is displayed.
10) Press  qw to select [OK], and press the  button.
Note
 f When a button operation is performed on the device set to [DISABLE], the  [CONTROL  DEVICE PASSWORD] screen is displayed.
Enter the control device password.
 f The 

[CONTROL DEVICE PASSWORD] screen will disappear when there is no operation for approx. 10 seconds.
 fIf the operations of both [CONTROL

 PANEL] and [REMOTE CONTROL] are set to [DISABLE], the projector cannot be turned off (cannot 
enter standby).
 f When the setting has completed, the menu screen will disappear

. To operate continuously, press the  button to display the main 
menu.
 f Even when button operation on the remote control is disabled, the  button and the  button are enabled.
[CONTROL DEVICE PASSWORD CHANGE]
The control device password can be changed.
1) Press as to select [CONTROL DEVICE PASSWORD CHANGE].
2)  
Press the  button.
 f The  [CONTROL DEVICE PASSWORD CHANGE]  screen is displayed.
3) Press asqw to select the text, and press the  button to enter the text.   
						

							Chapter 4 Settings — [SECURITY] menu
136 - ENGLISH
4) Press asqw to select [OK], and press the  button.
 fTo cancel, select [CANCEL].
Attention
 fThe initial password is “AAAA” by the factory default or when [ALL  USER DA TA] in [INITIALIZE] (x   page   125) is executed. fChange the password periodically that is hard to guess.   
						

							Chapter 4 Settings — [NETWORK] menu
ENGLISH - 137
[NETWORK] menu
On the menu screen, select [NETWORK] from the main menu, and select an i\
tem from the sub-
menu.
Refer to “Navigating through the menu” (x
  page   65) for the operation of the menu screen.
 fAfter selecting the item, press 

asqw to set.
[NETWORK SETUP]
Perform the initial setting of the network before using the network function.
1) Press  as to select [NETWORK SETUP].
2)  
Press the  button.
 f The  [NETWORK SETUP] screen is displayed.
3) Press  as to select an item, and change the settings according to the operation i\
nstructions of the 
menu.
[PROJECTOR NAME] Change the setting when using a DHCP server.
[DHCP] Set to [ON] when obtaining an IP address automatically using a DHCP server. Set to [OFF] when not 
using a DHCP server.
[IP ADDRESS] Enter the IP address when not using a DHCP server.
[SUBNET MASK] Enter the subnet mask when not using a DHCP server.
[DEFAULT GATEWAY] Enter the default gateway address when not using a DHCP server.
[STORE] Save the current network settings.
4) Press as to select [STORE], and press the  button.
5)  
When the confirmation screen is displayed, press  qw

 to select [OK], and press the  button.
Note
 f When using a DHCP  server, confirm that the DHCP server is running. fConsult your network administrator regarding the IP
 address, subnet mask, and default gateway.
 fWhen [Art-Net SETUP] is set to [ON(2.X.X.X)] or [ON(10.X.X.X)], [NETWORK SETUP] cannot be selected.
[NETWORK CONTROL]
Set up the control method of the network.
1) Press  as to select [NETWORK CONTROL].
2)  
Press the  button.
 f The  [NETWORK CONTROL] screen is displayed.
3) Press  as to select an item, and press qw to change the setting.
[WEB CONTROL] Set to [ON] to control with the web browser.
[PJLink CONTROL] Set to [ON] to control with the PJLink protocol.
[COMMAND CONTROL] Set to [ON] to control with the / terminal control command format 
(x
  page   176). Refer to “Control commands via LAN” ( x
  page   171).
[COMMAND PORT] Set the port number used for command control.
[CRESTRON RoomView] Set to [ON] to control with RoomView of Crestron Electronics, Inc.
[AMX D.D.] Set to [ON] to control with the controller of AMX Corporation.
Setting this function to [ON] enables detection through “AMX Device Discovery”. For details, refer to 
the website of AMX Corporation.
URL http://www.amx.com/
[STORE] Save the current network control settings.   
						

							Chapter 4 Settings — [NETWORK] menu
138 - ENGLISH
4) Press as to select [STORE], and press the  button.
5)  
When the confirmation screen is displayed, press  qw

 to select [OK], and press the  button.
[NETWORK STATUS]
Display the status of the projector network.
1) Press as to select [NETWORK STATUS].
2)  
Press the  button.
 f The  [NETWORK STATUS] screen is displayed.
[Art-Net SETUP]
Make settings to use the Art-Net function.
1) Press  as to select [Art-Net SETUP].
2)  
Press 
 qw to select an item.
 fThe items will switch each time you press the button.
[OFF] Disables the Art-Net function.
[ON(2.X.X.X)] Enables the Art-Net function and sets the IP address to 2.X.X.X.
[ON(10.X.X.X)] Enables the Art-Net function and sets the IP address to 10.X.X.X.
[ON(MANUAL)] Enables the Art-Net function and uses the IP address set in [NETWORK SETUP].
 fWhen an item other than [OFF] is selected, proceed to Step 

3).
3) Press the  button.
 fThe  [Art-Net SETUP] screen is displayed.
4) Press  as to select an item, and press qw to switch the setting.
[NET] Enter [NET] to be used when the projector processes Art-Net.
[SUB NET] Enter [SUB NET] to be used when the projector processes Art-Net.
[UNIVERSE] Enter [UNIVERSE] to be used when the projector processes Art-Net.
[START ADDRESS] Enter [START ADDRESS] to be used when the projector processes Art-Net.
5) Press as to select [STORE], and press the  button.
6)  
When the confirmation screen is displayed, press  qw

 to select [OK], and press the  button.
Note
 f When [ON(2.X.X.X)] or [ON(10.X.X.X)] is selected, the IP  address is searched and set automatically.
Network connections
The projector has a network function, and the following operations are available from the computer using the web control.
 fSetting and adjustment of the projector
 fDisplay of the projector status
 fSending of E-mail messages when there is a problem with the projector
The projector supports “Crestron RoomV

iew”, and the following application software of Crestron Electronics, Inc. can be used.
 fRoomV

iew Express
 fFusion R

V
 fRoomV

iew Server Edition
Attention
 fWhen a LAN cable is directly connected to the projector , the network connection must be made indoors.
Note
 f“Crestron RoomV iew” is a system of Crestron Electronics, Inc. that collectively manages and controls devices on multiple systems 
connected to a network using a computer.
 f For details of “Crestron RoomV

iew”, refer to the website of Crestron Electronics, Inc. (English only)
URL http://www.crestron.com
To download “RoomView Express”, go to the following website of Crestron Electronics, Inc. (English only)
URL http://www.crestron.com/getroomview
 f A

 LAN cable is required to use the network function.   
						

							Chapter 4 Settings — [NETWORK] menu
ENGLISH - 139
 rExample of a normal network connection
SDI 1/2
Computer
Projector
LAN cable (straight) LAN cable (straight) Hub
 fA web browser is required to use this function. Confirm that the web browser can be used beforehand.
Compatible OS: Windows XP/Windows Vista/Windows 7/Windows 8, Mac OS   X   v10.4/v10.5/v10.6/v10.7/v10.8
Compatible browser: Internet Explorer 7.0/8.0/9.0/10.0, Safari 4.0/5.0/6.0 (Mac OS)
 f Communication with an E-mail server is required to use the E-mail function. Confirm that the E-mail can be used beforehand.
 fUse a LAN cable that is compatible with category 5 or higher

.
 fUse a LAN cable of 100

  m (328'1") or shorter.
Name and function of network function parts
3 2
1
1 LAN LINK/ACT lamp (green)
Lights on when connected.
Flashes when transmitting/receiving data.
2
 
 terminal (10Base
 - T/100Base - TX)
Used to connect the LAN cable here.
3
 
LAN10/100 lamp (yellow)
Lights on when connected to the 100Base

- TX.   
						

							Chapter 4 Settings — [NETWORK] menu
140 - ENGLISH
Accessing from the web browser
1) Start up the web browser on the computer.
2)  
Enter the IP
  address set on the projector into the URL entry field of the web browser.
3)
 
Enter the user name and the password.
 f The factory default setting of the user name is user1 (user rights)/admin1 (administrator rights) and the password is panasonic (lower 
case).
4) Click OK.
 fThe [Projector status] page is displayed.