Panasonic Projector PT-DS12KU User Manual

							Chapter 6 Appendix — Technical information
ENGLISH - 181
ModeResolution
(Dots) Scanning freq.Dot clock 
freq.
(MHz)Format Plug and play
*1
Horizontal
(kHz)Vertical(Hz)RGB2 DVI - D
HDMIEDID1 EDID2 EDID3
1920 x 1080 1   920   x   1   080 55.6 49.9 141.5
R/D/H ― ― ― ― ―
1   920   x   1   080*866.6 59.9 138.5 R/D/H ― ― ― ― ―
1
 
920
 
x
 
1
 
080
*1067.2 60.0 173.0 R― ― ― ― ―
WUXGA 1
 
920
 
x
 
1
 
200 61.8 49.9 158.3 R/D/H ― ― ― ― ―
1
 
920
 
x
 
1
 
200
*874.0 60.0 154.0 R/D/H
l―
l l* 11l* 11
1 920 x 1 200*1074.6 59.9 193.3 R― ― ― ― ―
*1 Signals with l  in the Plug and play columns are signals described in EDID (extended display identification data) of the projector . A signal, which 
has no l in the Plug and play columns but has an entry in the Format column, can be input. For signals without  l in the Plug and play columns, 
resolution may not be selected in the computer even though the projector supports them.
*2
 
For single link connections only
*3

 
Pixel-Repetition signal (dot clock frequency 27.0
   MHz) only
*4
 
When a 1
 125 (1035)/60i signal was input, it is displayed as a 1125 (1080)/60i signal.
*5
 
Only for SDI1
*6

 
For dual link connections only
*7

 
When [3D INPUT
  FORMAT] is set to [AUTO], 3D images in frame sequential format are displayed. To display images in 2D, set [3D INPUT 
FORMAT] to [NATIVE].
*8
 
VESA
  CVT-RB (Reduced Blanking)-compliant
*9
 
Only for PT-
 DW11KU
*10
 
Samples the pixels in the image processing circuit and projects the image.
*1

1  
Only for PT-
 DZ13KU, PT
-
 DZ10KU
Note
 fThere are 1   920   x   1   080 display dots for PT- DZ13KU and PT- DZ10KU, 1   400   x   1   050 for PT- DS12KU, and 1   366   x   768 for PT- DW11KU. A 
signal with a different resolution is converted to the number of display dots.
 f The “i” at the end of the resolution indicates an interlaced signal. fWhen interlaced signals are connected, flickering may occur on the projected image.
List of 3D compatible signals
(Only for PT- DZ13KU, PT- DS12KU, PT- DW11KU)
The following table specifies the 3D compatible video signals that the projector can project.
Items that are applicable to  1 to 10 in the table are as follows.
1
 
Frame packing system
2

 
Side by side system
3

 
T
 op and bottom system
4
 
Line by line system
5

 
Frame sequential system
6

 
3G
 - SDI Level B simultaneous system
7
 
HDMI & DVI
 - D
8
 
RGB1 & RGB2
9

 
SDI1 & SDI2 (only for PT-
 DZ13KU, PT
-
 DS12KU)
10
 
Simultaneous system
3D compatible  signal Resolution
(Dots) Scanning freq.
Dot clock 
freq.
(MHz) HDMI
DVI - DHorizontal
(kHz)Vertical(Hz) 1 2*13 5 2*13 4 5
750 (720)/60p 1
 
280
 
x
 
720 45.0 60.0 74.3 l l l―
l l l ―
750 (720)/50p 1
 
280
 
x
 
720 37.5 50.0 74.3 l l l―
l l l ―
1080/60i 1
 
920
 
x
 
1
 
080i 33.8 60.0 74.3 l l― ―
l l― ―
1080/50i 1
 
920
 
x
 
1
 
080i 28.1 50.0 74.3 l l― ―
l l― ―
1080/24p 1
 
920
 
x
 
1
 
080 27.0 24.0 74.3 l l l―
l l ― ―
1080/24sF 1
 
920
 
x
 
1
 
080i 27.0 48.0 74.3 ― ― ― ― l l― ―
1080/25p 1
 
920
 
x
 
1
 
080 28.1 25.0 74.3 ― ― ― ― l l― ―
1080/30p 1
 
920
 
x
 
1
 
080 33.8 30.0 74.3 ― ― ― ― l l― ―
1080/60p 1
 
920
 
x
 
1
 
080 67.5 60.0 148.5 ― l l―
l l ― ―
1080/50p 1
 
920
 
x
 
1
 
080 56.3 50.0 148.5 ― l l―
l l ― ―
VGA480 640
 
x
 
480 31.5 59.9 25.2 ― ― ― ― l― ― ―
SVGA 800
 
x
 
600 37.9 60.3 40.0 ― ― ― ― l― ― ―   
						

							Chapter 6 Appendix — Technical information
182 - ENGLISH
3D compatible signal Resolution
(Dots) Scanning freq.
Dot clock 
freq.
(MHz) HDMI
DVI - DHorizontal
(kHz)Vertical(Hz) 1 2*13 5 2*13 4 5
XGA 1
 
024
 
x
 
768 39.6 50.0 51.9 ― ― ― ― l― ― ―
1
 
024
 
x
 
768 48.4 60.0 65.0 ― ― ― ― l― ― ―
1
 
024
 
x
 
768 81.4 100.0 113.3 ― ― ― l― ― ―
l
1
 
024
 
x
 
768 98.8 120.0 139.1 ― ― ― l― ― ―
l
MXGA 1
 
152
 
x
 
864 53.7 60.0 81.6 ― ― ― ― l― ― ―
1280
 
x
 
720 1
 
280
 
x
 
720 37.1 49.8 60.5 ― ― ― ― l― ― ―
1
 
280
 
x
 
720 44.8 59.9 74.5 ― ― ― ― l― ― ―
1
 
280
 
x
 
720 76.3 100.0 131.8 ― ― ― l― ― ―
l
1
 
280
 
x
 
720 92.6 120.0 161.6 ― ― ― l― ― ―
l
1280
 
x
 
768 1
 
280
 
x
 
768 39.6 49.9 65.3 ― ― ― ― l― ― ―
1
 
280
 
x
 
768 47.8 59.9 79.5 ― ― ― ― l― ― ―
1
 
280
 
x
 
768
*247.4 60.0 68.3 ― ― ― ― l― ― ―
1280
 
x
 
800 1
 
280
 
x
 
800 41.3 50.0 68.0 ― ― ― ― l― ― ―
1
 
280
 
x
 
800 49.7 59.8 83.5 ― ― ― ― l― ― ―
1
 
280
 
x
 
800
*249.3 59.9 71.0 ― ― ― ― l― ― ―
MSXGA 1
 
280
 
x
 
960 60.0 60.0 108.0 ― ― ― ― l― ― ―
SXGA 1
 
280
 
x
 
1
 
024 52.4 50.0 88.0 ― ― ― ― l― ― ―
1
 
280
 
x
 
1
 
024 64.0 60.0 108.0 ― ― ― ― l― ― ―
1366
 
x
 
768 1
 
366
 
x
 
768 47.7 59.8 85.5 ― ― ― ― l― ― ―
1
 
366
 
x
 
768 39.6 49.9 69.0 ― ― ― ― l― ― ―
SXGA+ 1
 
400
 
x
 
1
 
050 54.1 50.0 99.9― ― ― ―
l― ― ―
1
 
400
 
x
 
1
 
050 64.0 60.0 108.0 ― ― ― ― l― ― ―
1
 
400
 
x
 
1
 
050 65.2 60.0 122.6 ― ― ― ― l― ― ―
1
 
400
 
x
 
1
 
050 65.3 60.0 121.8 ― ― ― ― l― ― ―
WXGA+ 1
 
440
 
x
 
900 55.9 59.9 106.5 ― ― ― ― l― ― ―
1
 
440
 
x
 
900 46.3 49.9 86.8 ― ― ― ― l― ― ―
UXGA60 1
 
600
 
x
 
1
 
200 75.0 60.0 162.0 ― ― ― ― l― ― ―
WSXGA+ 1
 
680
 
x
 
1
 
050 65.3 60.0 146.3 ― ― ― ― l― ― ―
1
 
680
 
x
 
1
 
050 54.1 50.0 119.5 ― ― ― ― l― ― ―
1920
 
x
 
1080 1
 
920
 
x
 
1
 
080 55.6 49.9 141.5 ― ― ― ― l― ― ―
1
 
920
 
x
 
1
 
080
*266.6 59.9 138.5 ― ― ― ― l― ― ―
WUXGA 1
 
920
 
x
 
1
 
200 61.8 49.9 158.3 ― ― ― ― l― ― ―
1
 
920
 
x
 
1
 
200
*274.0 60.0 154.0 ― ― ― ― l―
l―
*1 Supports half.
*2  VESA  CVT RB (Reduced Blanking)-compliant   
						

							Chapter 6 Appendix — Technical information
ENGLISH - 183
3D compatible signal Resolution
(Dots) Scanning freq.
Dot clock 
freq.
(MHz) RGB1/RGB2 SDI1/SDI2 7 8 9Horizontal
(kHz)Vertical(Hz)2*13 4 5 2*13 4 6*310 10 10
750 (720)/60p 1
 
280
 
x
 
720 45.0 60.0 74.3 l l l―
l l l l l l l
750 (720)/50p 1
 
280
 
x
 
720 37.5 50.0 74.3 l l l―
l l l l l l l
1080/60i 1
 
920
 
x
 
1
 
080i 33.8 60.0 74.3 l l― ―
l l―
l l l l
1080/50i 1
 
920
 
x
 
1
 
080i 28.1 50.0 74.3 l l― ―
l l―
l l l l
1080/24p 1
 
920
 
x
 
1
 
080 27.0 24.0 74.3 l l― ―
l l―
l l l l
1080/24sF 1
 
920
 
x
 
1
 
080i 27.0 48.0 74.3 l l― ―
l l―
l l l l
1080/25p 1
 
920
 
x
 
1
 
080 28.1 25.0 74.3 l l― ―
l l―
l l l l
1080/30p 1
 
920
 
x
 
1
 
080 33.8 30.0 74.3 l l― ―
l l―
l l l l
1080/60p 1
 
920
 
x
 
1
 
080 67.5 60.0 148.5 l l― ―
l
*3l*3― ― l l―
1080/50p 1
 
920
 
x
 
1
 
080 56.3 50.0 148.5 l l― ―
l
*3l*3― ― l l―
VGA480 640
 
x
 
480 31.5 59.9 25.2 l― ― ― ― ― ― ― ― ― ―
SVGA 800
 
x
 
600 37.9 60.3 40.0 l― ― ― ― ― ― ― ― ― ―
XGA 1
 
024
 
x
 
768 39.6 50.0 51.9 l― ― ― ― ― ― ― ― ― ―
1
 
024
 
x
 
768 48.4 60.0 65.0 l― ― ― ― ― ― ― ― ― ―
1
 
024
 
x
 
768 81.4 100.0 113.3 ― ― ― l― ― ― ― ― ― ―
1
 
024
 
x
 
768 98.8 120.0 139.1 ― ― ― l― ― ― ― ― ― ―
MXGA 1
 
152
 
x
 
864 53.7 60.0 81.6 l― ― ― ― ― ― ― ― ― ―
1280
 
x
 
720 1
 
280
 
x
 
720 37.1 49.8 60.5 l― ― ― ― ― ― ― ― ― ―
1
 
280
 
x
 
720 44.8 59.9 74.5 l― ― ― ― ― ― ― ― ― ―
1
 
280
 
x
 
720 76.3 100.0 131.8 ― ― ― l― ― ― ― ― ― ―
1
 
280
 
x
 
720 92.6 120.0 161.6 ― ― ― l― ― ― ― ― ― ―
1280
 
x
 
768 1
 
280
 
x
 
768 39.6 49.9 65.3 l― ― ― ― ― ― ― ― ― ―
1
 
280
 
x
 
768 47.8 59.9 79.5 l― ― ― ― ― ― ― ― ― ―
1
 
280
 
x
 
768
*247.4 60.0 68.3 l― ― ― ― ― ― ― ― ― ―
1280
 
x
 
800 1
 
280
 
x
 
800 41.3 50.0 68.0 l― ― ― ― ― ― ― ― ― ―
1
 
280
 
x
 
800 49.7 59.8 83.5 l― ― ― ― ― ― ― ― ― ―
1
 
280
 
x
 
800
*249.3 59.9 71.0 l― ― ― ― ― ― ― ― ― ―
MSXGA 1
 
280
 
x
 
960 60.0 60.0 108.0 l― ― ― ― ― ― ― ― ― ―
SXGA 1
 
280
 
x
 
1
 
024 52.4 50.0 88.0 l― ― ― ― ― ― ― ― ― ―
1
 
280
 
x
 
1
 
024 64.0 60.0 108.0 l― ― ― ― ― ― ― ― ― ―
1366
 
x
 
768 1
 
366
 
x
 
768 47.7 59.8 85.5 l― ― ― ― ― ― ― ― ― ―
1
 
366
 
x
 
768 39.6 49.9 69.0 l― ― ― ― ― ― ― ― ― ―
SXGA+ 1
 
400
 
x
 
1
 
050 54.1 50.0 99.9
l― ― ― ― ― ― ―
l l―
1
 
400
 
x
 
1
 
050 64.0 60.0 108.0 l― ― ― ― ― ― ―
l l―
1
 
400
 
x
 
1
 
050 65.2 60.0 122.6 l― ― ― ― ― ― ―
l l―
1
 
400
 
x
 
1
 
050 65.3 60.0 121.8 l― ― ― ― ― ― ―
l l―
WXGA+ 1
 
440
 
x
 
900 55.9 59.9 106.5 l― ― ― ― ― ― ― ― ― ―
1
 
440
 
x
 
900 46.3 49.9 86.8 l― ― ― ― ― ― ― ― ― ―
UXGA60 1
 
600
 
x
 
1
 
200 75.0 60.0 162.0 l― ― ― ― ― ― ― ― ― ―
WSXGA+ 1
 
680
 
x
 
1
 
050 65.3 60.0 146.3 l― ― ― ― ― ― ― ― ― ―
1
 
680
 
x
 
1
 
050 54.1 50.0 119.5 l― ― ― ― ― ― ― ― ― ―
1920
 
x
 
1080 1
 
920
 
x
 
1
 
080 55.6 49.9 141.5 l― ― ― ― ― ― ― ― ― ―
1
 
920
 
x
 
1
 
080
*266.6 59.9 138.5 l― ― ― ― ― ― ― ― ― ―
WUXGA 1
 
920
 
x
 
1
 
200 61.8 49.9 158.3 l― ― ― ― ― ― ―
l l―
1
 
920
 
x
 
1
 
200
*274.0 60.0 154.0 l―
l― ― ― ― ―
l l―
*1 Supports half.
*2  VESA  CVT RB (Reduced Blanking)-compliant
*3
 
Only supports SDI1   
						

							Chapter 6 Appendix — Specifications
184 - ENGLISH
Specifications
The specifications of the projector are as follows.
Power supplyAC 120   V, 50   Hz/60   Hz
Power consumption PT
-

DZ13KU1
  000   W (9.3  
A)
PT
-

DS12KU, PT
-
 DW11KU980
  W (9.1  
A)
PT
-

DZ10KU925
  W (9  
A)
0.2

  W when [STANDBY MODE] is set to [ECO]
6
  W when [STANDBY MODE] is set to [NORMAL]
DLP chip Size
PT
-

DZ13KU, PT
-
 DZ10KU24.4
  mm (0.96") (aspect ratio 16:10)
PT
-

DS12KU24.1
  mm (0.95") (aspect ratio 4:3)
PT
-

DW11KU21.6
  mm (0.85") (aspect ratio 16:9)
Display system 3-unit DLP chips, DLP type
Number of pixels PT
-

DZ13KU, PT
-
 DZ10KU2
  304   000 pixels (1   920   x   1   200 dots)
PT
-

DS12KU1
  470   000 pixels (1   400   x   1   050 dots)
PT
-

DW11KU1
  049   088 pixels (1   366   x   768 dots)
Lens Optional
Luminous lamp PT
-

DZ13KU, PT
-
 DS12KU, 
PT
-

DW11KU380
  W UHM lamp x 2
PT
-

DZ10KU355
  W UHM lamp x 2
Light output
*1
PT- DZ13KU, PT- DS12KU 12   000   lm*2 (ANSI)
PT
-

DW11KU 11
 
000
 
lm
*2 (ANSI)
PT
-

DZ10KU 10
 
600
 
lm (ANSI)
Contrast ratio
*110 000:1 (when [DYNAMIC IRIS] is set to [3])
Color system 7 standards (NTSC/NTSC4.43/P
AL/PAL - N/PAL - M/SECAM/PAL60)
Projection screen size 1.78
  m (70") to 25.40   m (1   000")
Screen aspect ratio PT
-

DZ13KU, PT
-
 DZ10KU 16:10
PT
-

DS12KU 4:3
PT
-

DW11KU 16:9
Projection method [FRONT/CEILING], [FRONT/FLOOR], [REAR/CEILING], [REAR/FLOOR]
Power cable length 3.0
  m (118-1/8")
Outer case Molded plastic
Dimensions Width
530
  mm (20-7/8")
Height 200
  mm (7-7/8") (with legs at shortest position)
Depth 548.5
  mm (21-19/32") (excluding the lens)
Weight Approx. 24.0
  k] (52.9   lbs.)
*3
Noise level*1PT-DZ13KU, PT- DS12KU, 
PT- DW11KU 45
  dB
PT
-

DZ10KU 43
  dB
Operating 
environment
Operating 
environment 
temperature
*40 °C (32 °F) to 45 °C (113 °F)
Operating 
environment 
humidity 10
  % to 80   % (no condensation)
Remote 
control Power supply
DC 3
  V (AA/R6 battery x 2)
Operating range Within approx. 30
  m (98'5") (when operated directly in front of signal receiver)
Weight 134
  ] (4.7   ozs.) (including batteries)
Dimensions Width: 51
  mm (2"), Height: 176   mm (6-15/16"), Depth: 28   mm (1-3/32")
*1 Measurement, measuring conditions and method of notation all comply with ISO21 1 18 international standards.
*2  In the portrait setting, the light output is 10   600   lm for PT- DZ13KU and PT- DS12KU, and 9   600   lm for PT- DW11KU.
*3
 
A
 verage value. Weight varies for each product.
*4
 
When using the projector at high altitudes (1
   400   m (4   593') or higher – lower than 2   700   m (8   858') above sea level), the operating environment 
temperature should be between 0
  °C (32   °F) and 40   °C (104   °F).
If you use the Smoke cut filter, the operating environment temperature should be between 0
  °C (32   °F) and 35   °C (95   °F). However, it cannot be 
used at high altitudes.
If you use the Replacement lamp unit (for portrait mode), the operating environment temperature should be between 0
  °C (32   °F) and 40   °C 
(104
  °F) when using the projector at elevations lower than 1   400   m (4   593') above sea level, and between 0   °C (32   °F) and 35   °C (95   °F) when 
using the projector at high altitudes. If you use the Smoke cut filter together , the operating environment temperature should be between 0
  °C (32   °F) 
and 30
  °C (86   °F).
If the [PROJECTOR SETUP] menu → [LAMP POWER] is set to [HIGH], [MIDDLE], or [NORMAL], and an ambient temperature reaches 40
  °C 
(104
  °F) or higher (35   °C (95   °F) or higher when [HIGH ALTITUDE MODE] is set to [ON] or the Smoke cut filter is used), the light output may 
decrease by approx. 20
  % to protect the projector.   
						

							Chapter 6 Appendix — Specifications
ENGLISH - 185
 rApplicable scanning frequency
Refer to “List of compatible signals” ( x   page   179) for the types of video signals that can be used with the projector .
For video signal
(including Y/C signal)Horizontal: 15.75
  kHz/15.63   kHz, Vertical: 50   Hz/60   Hz
For RGB signal Horizontal: 15
  kHz to 100   kHz, Vertical: 24   Hz to 120   Hz
PIAS (Panasonic Intelligent Auto Scanning) system
 f Dot clock frequency: 162

  MHz or less
For YC
BCR/YPBPR signal
 f 525i (480i)
Horizontal: 15.75
   kHz, Vertical: 60   Hz
 f
525p (480p)
Horizontal: 31.5
   kHz, Vertical: 60   Hz
 f
750 (720)/60p
Horizontal: 45
   kHz, Vertical: 60   Hz
 f
1
 125 (1035)/60i
Horizontal: 33.75   kHz, Vertical: 60   Hz f
1 125 (1080)/50i
Horizontal: 28.13   kHz, Vertical: 50   Hz
 f1

125 (1080)/24sF
Horizontal: 27
  kHz, Vertical: 48   Hz
 f1

125 (1080)/30p
Horizontal: 33.75
  kHz, Vertical: 30   Hz
 f1

125 (1080)/50p
Horizontal: 56.25
  kHz, Vertical: 50   Hz
 f625i (576i)
Horizontal: 15.63
   kHz, Vertical: 50   Hz
 f
625p (576p)
Horizontal: 31.25
   kHz, Vertical: 50   Hz
 f
750 (720)/50p
Horizontal: 37.5
   kHz, Vertical: 50   Hz
 f
1
 125 (1080)/60i
Horizontal: 33.75   kHz, Vertical: 60   Hz f
1 125 (1080)/24p
Horizontal: 27   kHz, Vertical: 24   Hz
 f1

125 (1080)/25p
Horizontal: 28.13
  kHz, Vertical: 25   Hz
 f1

125 (1080)/60p
Horizontal: 67.5
  kHz, Vertical: 60   Hz
 fThe SYNC/HD and VD terminals do not support 3 value SYNC.
For DVI

-
D signal 525i (480i)
*1, 625i (576i)*1, 525p (480p), 625p (576p), 750 (720)/60p, 750 (720)/50p, 
 
1125 (1080)/60i, 1125 (1080)/50i, 1125 (1080)/24p,  
1125 (1080)/24sF, 1125 (1080)/25p, 1125 (1080)/30p,  
1125 (1080)/60p, 1125 (1080)/50p
 f Displayable resolution: VGA

 to WUXGA (non-interlaced)
 fDot clock frequency: 25

  MHz to 162   MHz
For HDMI signal 525i (480i)
*1, 625i (576i)*1, 525p (480p), 625p (576p), 750 (720)/60p, 750 (720)/50p, 
 
1125 (1080)/60i, 1125 (1080)/50i, 1125 (1080)/24p,  
1125 (1080)/24sF, 1125 (1080)/25p, 1125 (1080)/30p,  
1125 (1080)/60p, 1125 (1080)/50p
 f Displayable resolution: VGA

 to WUXGA (non-interlaced)
 fDot clock frequency: 25

  MHz to 162   MHz
For SDI signal
(Only for PT
-

DZ13KU, 
PT
-

DS12KU, PT
-

DZ10KU) SD
-
SDI signal SMPTE ST 259 compliant
YC
BCR 4:2:2 10-bit
480i, 576i
Single link HD
-
SDI signal SMPTE ST 292 compliant
YP
BPR 4:2:2 10-bit
720/50p, 720/60p, 1035/60i, 1080/50i, 1080/60i, 1080/25p, 
1080/24p, 1080/24sF
, 1080/30p
Dual link HD
-
SDI signal
*2SMPTE ST 372 compliant
RGB 4:4:4 12 - bit/10 - bit
1080/50i, 1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p
X'Y'Z' 4:4:4 12
- bit
2048
  x   1080/24p, 2048   x   1080/24sF
3G
-
SDI signal SMPTE ST 424 compliant
YP
BPR 4:2:2 10-bit
1080/50p, 1080/60p
RGB 4:4:4 12
- bit/10 - bit
1080/50i, 1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p
 f The 3G

-
SDI signal is only compatible with SDI1.
*1 Pixel-Repetition signal (dot clock frequency 27.0   MHz) only
*2  Only for PT- DZ13KU, PT- DS12KU   
						

							Chapter 6 Appendix — Specifications
186 - ENGLISH
 rTerminal
 terminal 1 set (BNC x 5 (RGB/YP
BPR/YCBCR/YC x 1))
RGB signal 0.7
 
V [p-p] 75   Ω (SYNC ON GREEN: 1.0   V [p-p] 75   Ω)
SYNC/HD TTL high impedance, automatic positive/negative 
polarity compatible
VD TTL high impedance, automatic positive/negative 
polarity compatible
YP
BPR signal Y: 1.0   V [p-p] including synchronization signal, PBPR: 0.7 V [p-p] 75 Ω
Y/C signal Y
: 1.0
 
V [p-p], C: 0.286
 
V [p-p] 75
 
Ω
 terminal 1 set, high-density D
-
Sub 15
 
p (female)
RGB signal 0.7
 
V [p-p] 75
 
Ω (SYNC ON GREEN: 1.0
 
V [p-p] 75
 
Ω)
SYNC/HD TTL high impedance, automatic positive/negative 
polarity compatible
VD TTL high impedance, automatic positive/negative 
polarity compatible
YP
BPR signal Y: 1.0   V [p-p] including synchronization signal, PBPR: 0.7 V [p-p] 75 Ω
 terminal 1 set, DVI
-
D 24
 
p, single link, DVI 1.0 compliant, HDCP compatible
 terminal 1 set, HDMI 19 pin, HDCP compatible, Deep Color compatible
 terminal 1 set, BNC 1.0
 
V [p-p] 75
 
Ω
 terminal (Only for 
PT
-

DZ13KU, PT
-

DS12KU)
 terminal (Only for 
PT
-

DZ10KU) 1 set (BNC)
SD
-
SDI signal SMPTE ST 259 compliant
HD
-
SDI signal SMPTE ST 292 compliant
3G
-
SDI signal SMPTE ST 424 compliant
Dual link HD
-
SDI 
(LINK
-
A) signal
*1SMPTE ST 372 compliant
 terminal
(Only for PT
-

DZ13KU, 
PT
-

DS12KU) 1 set (BNC)
SD
-
SDI signal SMPTE ST 259 compliant
HD
-
SDI signal SMPTE ST 292 compliant
Dual link HD
-
SDI 
(LINK
-
B) signal SMPTE ST 372 compliant
 terminal
(Only for PT
-

DZ13KU, 
PT
-

DS12KU, PT
-

DW11KU) 1 set (BNC)
During input setting TTL high impedance
During output setting TTL output: Maximum 10
  mA
 terminal
(Only for PT
-

DZ13KU, 
PT
-

DS12KU, PT
-

DW11KU) 1 set (BNC)
TTL output: Maximum 10
 
mA
/  
terminal D
-
Sub 9
 
p, 1 set each, RS
-
232C compliant, for computer control
/  terminal M3 stereo mini jack cable, 1 set each, for remote control (wired)/projector connection control
 terminal 1 set, D
-
Sub 9
 
p, for contact control
 terminal 1 set, RJ
-
45, for network connection, PJLink compatible, 10Base - T/100Base - TX, Art-Net compatible
*1 Only for PT-DZ13KU, PT- DS12KU
Note
 fThe model numbers of accessories and optional components are subject to change without prior notice.   
						

							Chapter 6 Appendix — Dimensions
ENGLISH - 187
Dimensions
Unit: mm
540 (21-1/4)
200 (7-7/8) 8.5 (11/32)
100 (3-15/16)
462 (18-3/16)
26 (1-1/32)
530 (20-7/8) 468 (18-7/16)
* Actual dimensions may differ depending on the product.   
						

							Chapter 6 Appendix — Precautions for Ceiling Mount Bracket for Projectors
188 - ENGLISH
Precautions for Ceiling Mount Bracket for Projectors
 fWhen installing the projector to a ceiling, be sure to use the specified optional Ceiling Mount Bracket for Projectors (Model No.: 
ET-
PKD310H (for High Ceilings), ET- PKD310S (for Low Ceilings), ET- PAD310 (Projector ceiling mount bracket)).
 fWhen installing the projector

, attach the drop-prevention kit included with the Ceiling Mount Bracket for Projectors.
 fAsk a qualified technician to do the installation work such as mounting the projector on the ceiling.
 fPanasonic takes no responsibility for any damage to the projector resulting from use of a ceiling mount bracket not manufactured by 
Panasonic or the inappropriate choice of location for installation, even if the warranty period of the projector has not expired.
 fUnused products must be removed promptly by a qualified technician.
 fUse a torque screwdriver or 

Allen torque wrench to tighten bolts to their specified tightening torques. Do not use electric screwdrivers or 
impact screwdrivers.
 f Read the Installation Instructions for the Ceiling Mount Bracket for Projectors for details.
 fThe model numbers of accessories and optional accessories are subject to change without prior notice.


M6
16 mm (5/8)
Bottom view
Model No. of Ceiling Mount Bracket for Projectors: ET-PKD310H (for High Ceilings) ET-PKD310S (for Low Ceilings)
ET-PAD310 (Projector ceiling mount bracket)
Torque: 4 ± 0.5 N·m   
						

							Index
ENGLISH - 189
0 – 9[3D COLOR MATCHING]    9 3
[3D FRAME DELA
Y]
     9 4
[3D INPUT
 FORMAT]
     92
[3D PICTURE BALANCE]
     9 3
[3D SAFETY
 PRECAUTIONS]
     9 5
[3D SETTINGS]
     68,   91
[3D SIMUL INPUT SETTING]
     92
[3D SYNC SETTING]
     9 1
[3D SYSTEM SETTING]
     9 1
[3D 
TEST MODE]
     9 4
[3D 
TEST PATTERN]
     9 5
AAccessories     2 0
 terminal
     26,   52
Adjusting adjustable feet
     4 5
[ADV
ANCED MENU]
     67,   85
Air filter unit
     160
Air filter unit compartment
     162
Art-Net
     18,   170
[Art-Net SETUP]
     138
[ASPECT]
     7 9
 button Remote control
    
 24,   63
Aspect function
     6 3
Attaching/removing the projection lens
     4 6
Automatic setup function
     6 2
[AUT
O SETUP]
     9 8
 button
Projector body
    
 26,   62
Remote control
     24,   62
[AUTO SIGNAL]
     9 8
B[BACK COLOR]    104
[BACKUP
 INPUT SETTING]
     99
[BLANKING]
     8 5
[BRIGHTNESS]
     7 2
[BRIGHTNESS CONTROL]
     11 2
CCautions on use      1 8
Cautions when installing
     1 6
Cautions when transporting
     1 6
Ceiling Mount Bracket for Projectors
     188
[CLAMP
 POSITION]
     8 6
[CLOCK PHASE]
     8 1
[COLOR]
     7 2
[COLOR MA
TCHING]
     9 6
[COLOR 
TEMPERATURE]
     7 2
Connecting the power cord
     5 2
Connecting to the projector with a cable
     29
Connection
     4 8
[CONTRAST]
     7 1
[CONTROL
 DEVICE PASSWORD CHANGE]
     135
[CONTROL
 DEVICE SETUP]
     134
[COOLING CONDITION]
     11 0
Crestron RoomV
iew
     138,   154
[CUT OFF]
     108
D[DARK TIME SETTING]    9 4
[DA
TE AND TIME]
     122
 button
Remote control
    
 24,   66
Deleting the registered signal
     130
[DIGIT
AL CINEMA REALITY]
     8 5
Dimensions
     187
Display language
     68,   90
[DISPLAY OPTION]
     68,   96
[DISPLAY SETTING]
     134
Disposal
     1 8
 button Projector body
    
 26,   62
Remote control
     2 4
[DVI-D IN]
     101
[DYNAMIC IRIS]
     7 6
E[EDGE BLENDING]    8 7
 button Projector body
    
 2 6
Remote control
     2 4
Expanding signal lock-in range
     131
FFilter indicator    158  button
Remote control  
  
 24,   56
[FRAME LOCK]
     8 9
[FRAME RESPONSE]
     8 8
[FREEZE]
     106
 button Remote control
    
 24,   63
Function button
     6 3
[FUNCTION BUTT
ON]
     122
G[GAMMA]    7 4
[GEOMETR
Y]
     8 1
H button
Projector body     26,   62
Remote control
     24,   62
[HDMI IN]
     101
[HIGH 
ALTITUDE MODE]
     11 0
I button
Remote control     24,   28
 button Remote control
    
 24,   28
[INITIALIZE]
     125
Initial setting
     22
[INPUT
 RESOLUTION]
     8 6
Installation mode
     3 1
K[KEYSTONE]    8 4
LLamp indicator      158
[LAMP
 POWER]
     11 2
[LAMP
 RELAY]
     111
[LAMP
 SELECT]
     11 0
Lamp unit cover
     2 5
[LARGE SCREEN CORRECTION]
     9 7
[LEFT/RIGHT
 SWAP]
     9 3
 button Projector body
    
 2 6
[LENS CALIBRA
TION]
     123
[LENS MEMOR
Y]
     123
 button Remote control
    
 2 4
List of compatible signals
     179
[LOAD 
ALL USER DATA]
     125
 button Remote control
    
 2 4
MMain menu    6 6
Main power switch
     26,   53
Maintenance
     160
 button Projector body
    
 26,   65
Remote control
     24,   65
Menu item
     6 7
NNavigating through the menu     6 5
[NETWORK]
     70,   137
Network connections
     138
[NETWORK CONTROL]
     137
[NETWORK SETUP]
     137
[NETWORK ST
ATUS]
     138
[NOISE REDUCTION]
     7 6
[NO SIGNAL
 SHUT-OFF]
     121
O button
Remote control     24,   61
[ON-SCREEN DISPLAY]
     103
On-screen menu
     6 5
Optional accessories
     2 1
P[PICTURE]    67,   71
[PICTURE MODE]
     7 1
[P
 IN P]
     69,   127
P IN P function
     127
[POSITION]
     67,   79
Power cord
     5 2
Power indicator 
     5 2 Power on button
Projector body  
   2 6
Remote control
    2 4
Power standby button Projector body
 
   2 6
Remote control
    2 4
Precautions for Ceiling Mount Bracket for 
Projectors
 
   188
Precautions for use
    1 6
Projecting
    5 6
[PROJECTION METHOD]
     109
Projector body
    2 5
[PROJECT
OR ID]
    109
[PROJECT
OR SETUP]
     69,   109
Protecting the registered signal
     131
R[RASTER POSITION]    8 9
Read this first!
    2
Registering new signals
    130
 terminal
    2 7
 terminal
     2 7
 terminal
     177
[REMOTE2 MODE]
    122
Remote control
    2 4
Remote control operations
    6 1
Renaming the registered signal
     130
Replacing the air filter unit
     162
Replacing the lamp unit
    162
Replacing the unit
    162
Resetting to the factory default
     6 6
 button Projector body
 
   26,   62
Remote control
    24,   62
 button Projector body
 
   26,   62
Remote control
    24,   62
[RGB IN]
    100
RoomV
iew
    154
[RS-232C]
    119,   173
S[SAFETY PRECAUTIONS MESSAGE]    9 5
[SA
VE ALL USER DATA]
    125
[SCHEDULE]
    11 7
[SCREEN SETTING]
    9 7
 button Projector body
 
   26,   62
Remote control
    24,   62
[SDI IN]
    101
Security
    1 8
[SECURITY]
    69,   133
[SECURITY PASSWORD]
     133
[SECURITY
 PASSWORD CHANGE]
     133
Selecting the input signal
    5 6
 terminal
    173
 terminal
    173
[SER
VICE PASSWORD]
    126
Setting remote control ID numbers
     2 8
Setting up
    3 1
[SHARPNESS]
    7 5
[SHIFT]
    7 9
 button Remote control
 
   24,   56
 button Projector body
 
   26,   61
Remote control
    24,   61
[SHUTTER SETTING]
    106
[SIGNAL
 LIST]
    69,   130
Specifications
    184
sRGB-compliant video
    7 8
[ST
ANDBY MODE]
    11 6
[ST
ARTUP INPUT SELECT]
     11 8
[ST
ARTUP LOGO]
    105
[ST
ATUS]
    120
 button
Remote control
 
   24,   62
Sub memory
    132
Switching of
f the projector
    5 5
Switching on the projector
    5 3
Switching the input signal
    6 2
[SYSTEM DA
YLIGHT VIEW]
     7 5
[SYSTEM SELECT
OR]
    7 7
TTemperature indicator    158
 button Remote control
 
   24,   63
[TEST PATTERN]
    69,   129
Index   
						

							Index
190 - ENGLISH
[TEXT CHANGE]    134
[TINT]
     7 2
T
roubleshooting
     166
T
wo window
     178
U[UNIFORMITY]    105
Upgrade Kit
     179
V button
Projector body     26,   62
Remote control
     24,   62
W[WAVEFORM MONITOR]    106
Z[ZOOM]     8 0
 button Remote control
    
 24,   56