Panasonic Projector Pt Lz370u Operating Instructions

							[PROJECTOR SETUP] menu
ENGLISH - 71
Settings
[EMULATE]
When using the control commands for one of our 
projectors that you have previously purchased 
to control this projector using a computer via its 
 input terminal, set up the function as 
follows. This will allow you to use the control software 
etc. designed for our existing projectors.
1) Press ▲▼ to select [EMULA
TE].
2)  
Press the  button.
▶z The  [EMULATE] individual adjustment screen 
is displayed.
3) Press  ▲▼ to select an item.
[DEFAULT]
LZ370 series
[D3500] D3500 series
[D4000] D4000 series
[D/W5k series] DX800 series, DW730 series, 
D5700 series, DW5100 series, 
D5600 series, DW5000 series, 
D5500 series
[D/W/Z6k 
series] DZ6710 series, DZ6700 series, 
DW6300 series, D6000 series, 
D5000 series, DZ570 series, 
DW530 series, DX500 series
[L730] L730 series, L720 series, 
L520
  series
[L780] L780 series, L750 series
[L735] L735 series
[L785] L785 series
[LB/W series] LB3 series, LB2 series, 
LB1
  series, ST10 series, 
LB90
  series, LW80NT series, 
LB80 series, LB75 series
[F/W series] FW430 series, FX400 series, 
FW300 series, F300 series, 
F200
  series, FW100 series, 
F100
  series
4) Press the  button.
Note
 zRefer to “ terminal” ( page 113).
[FUNCTION BUTTON]
The functions assigned to the  to  
buttons are displayed. You can also release the 
assignment settings.
▶■ To cancel assigned functions 
to the  to  
buttons
1) Press  ▲▼ to select [FUNCTION 
BUTT ON].
2)
 
Press the  button.
3)

 
Press  ▲▼ to select [DISABLE] for a 
function button (F1 to F3) you want to 
release the assignment.
4)

 
Press the  button.
5)

 
When the confirmation message is 
displayed, select [OK] and press the 
 button. 
						

							[PROJECTOR SETUP] menu
72 - ENGLISH
Settings
[AUDIO SETTING]
Displays the details of the audio functions.
1) Press ▲▼ to select [AUDIO SETTING].
2)  
Press the  button.
▶z The  [AUDIO SETTING]
 screen is displayed.
3) Press 
▲▼ to select an item, and 
press  ◀▶ to adjust levels or change 
settings.
▶■ [VOLUME]
Adjusts the volume of the speaker.
Operation Adjustment Range
Press  ▶. Increases the 
volume. Maximum 
value 63
Press  ◀. Decreases the 
volume. Minimum 
value 0
▶■ [BALANCE]
You can adjust the balance of left/right audio output.
Operation Adjustment Range
Press  ▶. Increases the 
volume from the 
right.
L16 to R16
Press  ◀. Increases the 
volume from the 
left.
▶■
[IN ST ANDBY MODE]
You can set the audio output during the standby.
 z
The setting will change as follows each time you 
press the button.
[OFF][ON]
[OFF] Disables audio output during the 
standby.
[ON] Enables audio output during the 
standby.
Note
 z Y

ou cannot enable sound output during standby 
if [STANDBY MODE] (
 page 70) of [ECO 
MANAGEMENT] is set [ECO].
▶■ [AUDIO IN SELECT]
You can select the audio input from connected 
external equipment.
 z
The setting will change as follows each time you 
press the button.
▶zTo set [HDMI 1]
[HDMI 1 AUDIO IN][AUDIO IN]
[HDMI 1 AUDIO IN]Outputs HDMI 1 audio when the 
HDMI 1 input is selected.
[AUDIO IN] Outputs audio from the device 
connected to the  
terminal when the HDMI 1 input is 
selected.
▶z
To set [HDMI 2]
[HDMI 2 AUDIO IN][AUDIO IN]
[HDMI 2 AUDIO IN]Outputs HDMI 2 audio when the 
HDMI 2 input is selected.
[AUDIO IN] Outputs audio from the device 
connected to the  
terminal when the HDMI 2 input is 
selected.
Note
 z Sound is output from the device connected to the 
 terminal when you have set an input 
selection item other than [HDMI 1] or [HDMI 2]. 
						

							[PROJECTOR SETUP] menu
ENGLISH - 73
Settings
[DATE AND TIME]
You can set the time zone, date, and time of the built-
in clock of the projector.
By default, the time is set to +09:00.
▶■To set the time zone
1) Press 
▲▼ to select [DA
TE AND TIME].
2)  
Press the  button.
▶z The  [DATE AND TIME] screen is displayed.
3) Press 
▲▼ to select [TIME ZONE].
4)  
Press  ◀▶ to switch [TIME ZONE].
▶■To adjust the date and time 
automatically
1) Press  ▲▼ to select [DA
TE AND TIME].
2)  
Press the  button.
▶z The  [DATE AND TIME] screen is displayed.
3) Press 
▲▼ to select [ADJUST CLOCK].
4)  
Press the  button.
▶z The  [ADJUST CLOCK] screen is displayed.
5) Press 
▲▼ to select [NTP
 
SYNCHRONIZATION], and press  ◀▶ 
to change the setting to [ON].
▶z The setting will change as follows each time 
you press the button.
[OFF][ON]
[OFF]
Does not synchronize NTP server.
[ON] Synchronizes NTP server.
6) Press 
▲▼ to select [OK], and press 
the  button.
▶z The setting of the date and time will be 
completed.
▶■ To adjust the date and time 
manually
1) Press  ▲▼ to select [DA
TE AND TIME].
2)  
Press the  button.
▶z The  [DATE AND TIME] screen is displayed.
3) Select [ADJUST CLOCK].
4)  
Press the  button.
▶z The  [ADJUST CLOCK] screen is displayed.
5) Press 
▲▼ to select [NTP
 
SYNCHRONIZATION], and press  ◀▶ 
to change the setting to [OFF].
6)
 
Press  ▲▼ to select the item to be set, 
and press  ◀▶ to set the local date 
and time.
7)

 
Press  ▲▼ to select [OK], and press 
the  button.
▶z The setting of the date and time will be 
completed.
Note
 z T

o set the date and time automatically, the projector 
must be connected to the network.
 z If synchronization with the NTP

 server fails 
just after [NTP SYNCHRONIZATION] is turned 
[ON], or if [NTP SYNCHRONIZATION] is turned 
[ON] while the NTP server is not set, [NTP 
SYNCHRONIZATION] will return to [OFF].
 z Access the projector via a web browser to set 
the NTP

 server. Refer to “[Adjust clock] page” 
(
 page 87) for details. 
						

							[PROJECTOR SETUP] menu
74 - ENGLISH
Settings
[TEST PATTERN]
Displays the test pattern built-in to the projector.
Settings of position, size, and other factors will not 
be reflected in test patterns. Make sure to display the 
input signal before performing various adjustments.
1) Press ▲▼ to select [TEST P
ATTERN].
2)  
Press the  button.
▶z The test pattern is displayed.
3) Press 
◀▶ to switch the various test 
patterns.
▶z Press the  button or the  
button to return to the sub-menu of 
[PROJECT
OR SETUP].
▶■To display sequence of internal 
test patterns
The setting will change as follows each time you 
press  ◀▶.
Horizontal linesAll white
Vertical lines Color bars
\fotsWhite cross on blac\bk backgro\bnd
Cross hatch
Black cross on whit\be backgro\bnd
Note
 z The default screen is all white. If you assign this to 
the  to  buttons, Cross hatch 
becomes the default.
[INITIALIZE ALL]
You can return various setting values to the factory 
default settings.
When you perform this function, the projector enters 
standby mode to initialize.
1) Press 
▲▼ to select [INITIALIZE 
ALL].
2)  
Press the  button.
▶z [INITIALIZE  ALL] is displayed.
▶z
Password entry is required if you have set [ON] 
in the [SECURITY] menu 
→ [P

ASSWORD] 
(
 page 75).
3) Press  ◀▶ to select [OK].
4)  
Press the  button.
▶z The [NOW INITIALIZING...] screen appears, 
and is followed by [POWER OFF
.].
5) Press the  button.
▶zKey operations other than the  button 
and the power 
 button are unavailable at 
this time.
6) Wait until the power indicator  of the projector 
illuminates or flashes red (the fan 
stops).
7)
 
Press the  side of the  switch to turn off the power

.
▶zThe initial setting screen appears the next time 
the projector is started. (
 page 20)
Note
 z The projector usage time, lamp usage time, and 
[NETWORK] settings are not initialized.
 zAfter performing initialization, the password is 
returned to its factory default and [P

ASSWORD] is 
set to [OFF]. 
						

							[SECURITY] menu
ENGLISH - 75
Settings
[SECURITY] menu
Select [SECURITY] from the main menu, and 
select the item from the sub-menu.
Refer to “Navigating through the menu” 
(
 page 44) for the operation of the menu 
screen.
 z When the projector is used for the first time
Initial password: Press 
▲▶▼◀▲▶▼◀ in 
order

, and press the  button.
 zAfter selecting the item, press 
▲▼◀▶ to set.
Attention
 z
Make the settings after displaying the 
[SECURITY]

 
screen.
 z When the 

[SECURITY] screen is displayed, 
entering a password is required. Enter the set 
password and then continue operations.
 z When the password has been changed previously

, 
enter the changed password, and press the 
 button.
Note
 z The entered password is displayed with * mark on 
the screen.
[PASSWORD]
You can set to display the security password entry 
screen when the projection starts. If the correct 
password is not entered, any operation other than the 
power 
 button operations becomes unavailable.
1) Press 
▲▼ to select [P
ASSWORD].
2)  
Press  ◀▶ to switch [P

ASSWORD].
▶zThe setting will change as follows each time 
you press the button.
[OFF][ON]
[OFF] Disables the security password 
entry.
[ON] Enables the security password 
entry.
Note
 z
The [P

ASSWORD] is set to [OFF] by default and 
after you perform initialization.
 z Change the password periodically that is hard to 
guess.
 zThe security password will be enabled after setting 
[P

ASSWORD] to [ON] and turning off the power 
(standby mode).
[PASSWORD CHANGE]
You can change the security password.
1) Press  ▲▼ to select [P
ASSWORD 
CHANGE].
2)
 
Press the  button.
▶z The  [PASSWORD CHANGE] screen is 
displayed.
3) Press  ▲▼◀▶  and number ( - ) 
buttons to set the password.
▶z Up to eight button operations can be set.
4) Press the  button.
5)  
Re-enter the password for the 
confirmation.
6)

 
Press the  button.
Note
 z The entered password is displayed with * mark on 
the screen.
 zAn error message is displayed on the screen when 
the entered password is incorrect. Re-enter the 
correct password.
 zWhen numerals are used in the security password, 
initialization of the security password will be 
necessary if the remote control is lost. For the 
method of initialization, consult your dealer

. 
						

							[SECURITY] menu
76 - ENGLISH
Settings
[DISPLAY SETTING]
You can overlap the security message (text or image) 
over the projecting image.
1) Press ▲▼ to select [DISPLA
Y 
SETTING].
2)
 
Press  ◀▶ to switch [DISPLA

Y 
SETTING].
▶z The setting will change as follows each time 
you press the button.
[OFF][TEXT][USER 
LOGO]
[OFF] Disables the text/user logo 
display.
[TEXT] Enables the text display.
[USER LOGO] Projects the logo transferred with 
“Logo Transfer Software”
*1.
*1: “Logo Transfer Software” is included in the attached CD-
ROM.
Note
 zT

o create the image for [USER LOGO], “Logo 
Transfer Software” included in the supplied CD-
ROM is required.
 z Y

ou cannot display both security message and 
closed caption at the same time.
[TEXT CHANGE]
You can change the text displayed when the text 
display is enabled by selecting [TEXT] in [DISPLAY 
SETTING].
1) Press  ▲▼ to select [TEXT CHANGE].
2)  
Press the  button.
▶z The  [TEXT CHANGE] screen is displayed.
3) Press 
▲▼◀▶  to select the text, and 
press the  button to enter the 
text.
▶z Up to 22 characters can be entered.
4) Press 
▲▼◀▶  to select [OK], and 
press the  button.
▶z The text is changed.
[MENU LOCK]
You can set whether to display the menu and perform 
the menu operation when you press the  
button.
1) Press 
▲▼ to select [MENU LOCK].
2)  
Press  ◀▶ to switch [MENU LOCK].
▶z
The setting will change as follows each time 
you press the button.
[OFF][ON]
[OFF] Disables the lock of the menu 
operation.
[ON] Locks the menu operation.
Note
 z If an incorrect menu lock password is entered after 
[MENU LOCK] is set to [ON], the menu operation is 
disabled.
 zThe [MENU LOCK] is set to [OFF] by default and 
after you perform initialization.
 zThe unlock status is maintained until the projector 
is set to the standby mode. 
						

							[SECURITY] menu
ENGLISH - 77
Settings
[MENU LOCK PASSWORD]
You can change the MENU LOCK PASSWORD.
1) Press ▲▼ to select [MENU LOCK 
P ASSWORD].
2)
 
Press the  button.
▶z The  [MENU LOCK PASSWORD] screen is 
displayed.
3) Press  ▲▼◀▶  to select the text, and 
press the  button to enter the 
text.
▶z Up to 16 characters can be entered.
4) Press 
▲▼◀▶  to select [OK], and 
press the  button.
▶z Select [CANCEL] to stop.
Attention
 z The initial password when used for the first time or 
after initializing is “AAAA”.
 zChange the password periodically that is hard to 
guess.
[CONTROL DEVICE SETUP]
You can enable/disable the button operations on the 
control panel and the remote control.
1) Press 
▲▼ to select [CONTROL
 
DEVICE SETUP].
2)
 
Press the  button.
▶z The  [CONTROL DEVICE SETUP] screen is 
displayed.
3) Press  ▲▼ to select an item, and press 
◀▶  to change the setting.
▶z
When the confirmation message is displayed 
after setting [DISABLE], select [OK] and press 
the  button.
▶■ [CONTROL  PANEL]
▶z
You can set the limitation on the control from 
the control panel.
[ENABLE] Enables the button operation from 
the main unit.
[DISABLE] Disables the button operation from 
the main unit.
▶■
[REMOTE CONTROLLER]
▶z
You can set the limitation on the control from 
the remote control.
[ENABLE] Enables the button operation from 
the remote control.
[DISABLE] Disables the button operation from 
the remote control.
Note
 z It will not be possible to turn of

f the power (standby 
status) if the operations of both of [CONTROL 
PANEL] and [REMOTE CONTROLLER] are set to 
[DISABLE].
Canceling [DISABLE] setting: Press the  button while holding down 
the  button for at least two seconds on 
the main unit controls to reset the [DISABLE] 
setting on [CONTROL PANEL] to [ENABLE].
Use the control panel of the projector to change 
the setting of [REMOTE CONTROLLER]. 
						

							[NETWORK] menu
78 - ENGLISH
Settings
[NETWORK] menu
Select [NETWORK] from the main menu, and 
select the item from the sub-menu.
Refer to “Navigating through the menu” 
(
 page 44) for the operation of the menu 
screen.
 z After selecting the item, press 
▲▼◀▶ to set.
[WIRED LAN]
Perform the initial setting of the network before using 
the network function.
1) Press 
▲▼ to select [WIRED LAN].
2)  
Press the  button.
▶z The  [WIRED DETAILED SETUP] screen is 
displayed.
3) Press  ▲▼ to select an item, and 
change the settings according to the 
operation instructions of the menu.
[DHCP] Set the item to [ON] when using 
a DHCP server to automatically 
acquire the IP address. Set to 
[OFF] when not using a DHCP 
server.
[IP ADDRESS] Enter the IP address when not 
using a DHCP server.
[SUBNET  MASK] Enter the subnet mask when not 
using a DHCP server.
[DEFAULT 
GATEWAY] Enter the default gateway address 
when not using a DHCP server.
4) Press 
▲▼◀▶  to select [OK], and 
press the  button.
▶z Save the current network settings.
Note
 zWhen using a DHCP

 server, confirm that the DHCP 
server is running.
 z Consult your network administrator regarding the IP

 
address, subnet mask, and default gateway.
 z The following settings are applied by default.
[DHCP]
[OFF]
[IP ADDRESS] 192.168.10.100
[SUBNET MASK] 255.255.255.0
[DEFAULT GATEWAY] 192.168.10.1
[NAME CHANGE]
You can change the name of the projector displayed 
on the network.
1) Press 
▲▼ to select [NAME CHANGE].
2)  
Press the  button.
▶z The  [NAME CHANGE]
 screen is displayed.
3) Press 
▲▼◀▶  to select the text, and 
press the  button to enter the 
text.
▶z Select [ALL  DELETE] to delete all the entered 
characters, or press the  button on 
the remote control to delete a character on the 
cursor in the entry field.
4) After entering the name, press  ▲▼
◀▶  to select [OK], and press the 
 button.
▶z To cancel the change of the name, select 
[CANCEL] and press the  button.
Note
 z The projector name is set to Name0000 by default. 
						

							[NETWORK] menu
ENGLISH - 79
Settings
[NETWORK CONTROL]
You can set this function to control the projector from 
a computer connected via the network.
1) Press ▲▼ to select [NETWORK 
CONTROL].
2)
 
Press  ◀▶ to switch [NETWORK 
CONTROL].
▶z Each time you press the button, the settings 
change as follows.
[ON][OFF]
[ON] Enables the control function from 
a computer connected via the 
network.
[OFF] Disables the control function from 
a computer connected via the 
network.
[STATUS]
You can display the network status of the projector.
1) Press 
▲▼ to select [ST
ATUS].
2)  
Press the  button.
▶z The  [STATUS] screen is displayed.
[INITIALIZE]
You can restore the network settings to the factory 
default settings.
1) Press 
▲▼ to select [INITIALIZE].
2)  
Press the  button.
▶z [INITIALIZE] is displayed.
Note
 z The security password entry is required if you have 
s

et [ON] in the [SECURITY] menu  → [PASSWORD] 
(
 page 75).
3) Press  ◀▶ to select [OK], and press 
the  button. 
						

							[NETWORK] menu
80 - ENGLISH
Settings
Network connections
The projector has a network function, and the following operations are available from the computer using the Web 
browser control.
 zSetting and adjustment of the projector
 zDisplay of the projector status
 zSetting of E-mail notification
“Crestron RoomV

iew” is a system developed by Crestron Electronics, Inc. which collectively manage and 
control multiple system devices connected via the network, from a computer . This projector supports “Crestron 
RoomView”.
 z For details of “Crestron RoomV

iew”, refer to the Crestron Electronics, Inc. website. (Provided only in English.)
URL http://www.crestron.com
For the download of “Crestron RoomView Express”, refer to the Crestron Electronics, Inc. website. (Provided 
only in English.)
URL http://www.crestron.com/getroomview
Note
 z A

 LAN cable is required to use the network function.
 zThe information and the URL

 of the website may be changed or deleted without notice.
 zA Web browser is required to use this function. Confirm that the Web browser can be used beforehand.
Compatible OS: Windows XP/Windows Vista/Windows 7, Mac OS X v10.4/v10.5/v10.6/v10.7
Compatible browser: Internet Explorer 7.0/8.0/9.0, Safari 4.0/5.0 or later (Mac OS)
 z Communication with an E-mail server is required to use the E-mail function. Confirm that the E-mail can be 
used beforehand.
 zUse a LAN cable that is straight-through or crossover*1 and compatible with category 5 or higher.*1: Depending on the system configuration, the type of the LAN cable that can be used may be either straight-through, 
crossover
, or both. Consult your network administrator for the details.
 zUse a LAN cable with the length of 100 m (328'1") or shorter
.
Required environment for computer connection
 zCheck if your computer is equipped with wired LAN beforehand.
 zBefore connecting the projector to your computer

, be sure to check the following settings.
▶■Check 1: LAN cable
▶z
Is the cable connected correctly?
▶zUse a LAN cable compatible with category 5 or higher

.
▶■Check 2: W ired LAN settings
A computer equipped with wired LAN function
▶z
Is the wired LAN function activated?
A

 computer not equipped with wired LAN function
▶z Is the wired LAN adapter recognized correctly?
▶zIs the wired LAN adapter activated?
▶zInstall the wired LAN adapter driver before you use the network function.
R

efer to the instruction manual of the wired LAN adapter for the installation of the driver.