Panasonic Projector PT-RS11K User Manual

							Chapter 4 Settings — [SIGNAL LIST] menu
ENGLISH - 151
 fWhen a signal to be input corresponds to multiple signals set in [WIDE], a registered signal with a high memory number receives priority . 
Example: a signal to be input that corresponds to memory numbers  A2, 
A4 and B1 will be determined to be B1.
 fWhen a registration signal is deleted, the settings are also deleted. fIn an environment where multiple types of signals are input to the same \
terminal, signals are sometimes not determined correctly when the 
setting is set to [WIDE].
Sub memory
The projector has a sub memory function that can register the multiple i\
mage adjustment data, even if it is 
recognized as the same signal by the frequency or format of the synchronization signal source.
Use this function when you need to adjust the picture quality such as switching of the aspect ratio or white 
balance by the same signal source. The sub memory includes all the data that can be adjusted for each signa\
l, 
such as the image aspect ratio and data adjusted in the [PICTURE] item ([CONTRAST], [BRIGHTNESS], etc.).
Registering to the sub memory
1) While in the normal screen (where no menu is displayed), press  qw .
 fThe sub memory registration screen is displayed if the sub memory is not\
 registered. Proceed to Step  3)

.
 fA

 list of sub memories registered to the signal currently input is displayed.
 fThe  button on the remote control can be used instead of  qw

 when [SUB MEMORY] is 
selected from the [PROJECTOR SETUP] menu → [FUNCTION BUTTON].
2)
 
Press 
 asqw to select the sub memory number to register in [SUB MEMORY LIST].
3)
 
Press the  button.
 fThe 

[SIGNAL NAME CHANGE] screen is displayed.
4)
 
Press 
 asqw to select [OK], and press the  button.
 fT

o rename the registered signal, follow the procedure in Steps  6) and 7) in “Renaming the registered signal” 
(x
  page   149).
Switching to the sub memory
1) While in the normal screen (where no menu is displayed), press  qw .
 fA

 list of sub memories registered to the signal currently input is displayed.
2)
 
Press 
 asqw to select the signal to switch in [SUB MEMORY LIST].
3)
 
Press the  button.
 fThis switches to the signal selected in Step  2)

.
Deleting the sub memory
1) While in the normal screen (where no menu is displayed), press  qw .
 fThe 

[SUB MEMORY LIST]  screen is displayed.
2)
 
Press 
 asqw to select the sub memory to be deleted, and press the  button on the 
remote control.
 f The 

[REGISTERED SIGNAL DELETE] screen is displayed.
 fT

o cancel the deletion, press the  button to return to the  [SUB MEMORY LIST] screen.
3)
 
Press the  button.
 fThe selected sub memory will be deleted.  
						

							Chapter 4 Settings — [SECURITY] menu
152 - ENGLISH
[SECURITY] menu
On the menu screen, select [SECURITY] from the main menu, and select an item from the sub-menu.
Refer to “Navigating through the menu” (x
  page   76) for the operation of the menu screen.
 fWhen the projector is used for the first time
Initial password: Press  awsqawsq in order

, and press the  button.
Attention
 f When you select the [SECURITY] menu and press the  button, entering a password is required. Enter the preset password and 
then continue operations of the [SECURITY] menu.
 fWhen the password has been changed previously

, enter the changed password, and press the  button.
Note
 fThe entered password is displayed with * marks on the screen. fAn error message is displayed on the screen when the entered password is incorrect. Re-enter the correct password.
[SECURITY PASSWORD]
Display the  [SECURITY PASSWORD] screen when the power is turned on with the  switch set 
to the  side. When the entered password is incorrect, the operation will be restricted to the power standby 
 button, the  button, and the  buttons (, , ).
1)
 
Press 
 as to select [SECURITY PASSWORD].
2)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Disables the security password entry.
[ON] Enables the security password entry.
Note
 fThe [SECURITY  PASSWORD] setting is set to [OFF] by the factory default or when [ALL USER DATA] in [INITIALIZE] ( x   page   144) is 
executed.
 f Change the password periodically that is hard to guess. fThe security password is enabled after setting [SECURITY

 PASSWORD] to [ON] and turning the  switch to .
[SECURITY PASSWORD CHANGE]
Change the security password.
1) 
Press 
 as to select [SECURITY PASSWORD CHANGE].
2)
 
Press the  button.
 fThe 

[SECURITY PASSWORD CHANGE] screen is displayed.
3)
 
Press 
 asqw and the number ( - ) buttons to set the password.
 fUp to eight button operations can be set.
4)

 
Press the  button.
5)

 
Re-enter the password for the confirmation.
6)

 
Press the  button.
Note
 f The entered password is displayed with * marks on the screen. fWhen numerical values are used for the security password, the security password is required to be initialized if the remote control is lost. 
Consult your dealer for the method of initialization.
[DISPLAY SETTING]
Overlap the security message (text or image) over the projecting image.
1)
 
Press 
 as to select [DISPLAY SETTING].  
						

							Chapter 4 Settings — [SECURITY] menu
ENGLISH - 153
2) Press qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Hides the security message.
[TEXT] Displays the text set in the [SECURITY] menu → [TEXT CHANGE].
[USER LOGO] Displays the image registered by the user.
Note
 fTo create/register the [USER LOGO] image, use “Logo Transfer Software” included in the supplied CD-ROM.
[TEXT CHANGE]
Edit the text to be displayed when [TEXT] is selected in [DISPLA Y SETTING].
1)  
Press 
 as to select [TEXT CHANGE].
2)
 
Press the  button.
 fThe 

[TEXT CHANGE] screen is displayed.
3)
 
Press 
 asqw to select the text, and press the  button to enter the text.
4)
 
Press 
 asqw to select [OK], and press the  button.
 fThe text is changed.
[CONTROL DEVICE SETUP]
Enable/disable the button operations on the control panel and the remote\
 control.
1)
 
Press 
 as to select [CONTROL DEVICE SETUP].
2)
 
Press the  button.
 fThe 

[CONTROL DEVICE SETUP] screen is displayed.
3)
 
Press 
 as to select [CONTROL PANEL] or [REMOTE CONTROL].
[CONTROL PANEL] You can set the limitation on the control from the control panel.
[REMOTE CONTROL] You can set the limitation on the control from the remote control.
4) Press the  button.
 fThe 

[CONTROL PANEL] screen or the [REMOTE CONTROL] screen is displayed.
5)
 
Press 
 as to select [CONTROL PANEL] or [REMOTE CONTROL].
6)
 
Press 
 qw to switch the item.
 fY

ou can set the operation restriction from the control panel or the remot\
e control.
[ENABLE] Enables all button operations.
[DISABLE] Disables all button operations.
[USER] Operation of all buttons can be enabled/disabled separately.
Refer to “Enabling/disabling any button” (
x
  page   153) for details.
7) Press as to select [APPLY], and press the  button.
 fThe confirmation screen is displayed.
8)

 
Press 
 qw to select [OK], and press the  button.
Enabling/disabling any button
1) Press  as to select [CONTROL DEVICE SETUP].
2)  
Press the  button.
 fThe 

[CONTROL DEVICE SETUP] screen is displayed.
3)
 
Press 
 as to select [CONTROL PANEL] or [REMOTE CONTROL].  
						

							Chapter 4 Settings — [SECURITY] menu
154 - ENGLISH
4) Press the  button.
 fThe 

[CONTROL PANEL] screen or the [REMOTE CONTROL] screen is displayed.
5)
 
Press 
 as to select [CONTROL PANEL] or [REMOTE CONTROL].
6)
 
Press 
 qw to switch [USER].
7)
 
Press 
 as to select the button item to set.
 fWhen [INPUT

 SELECT BUTTON] is selected, press the  button, and then press as to select 
the button to set.
Buttons that can be set
[CONTROL PANEL] [REMOTE CONTROL]
[POWER BUTTON] Power standby  button, power on  button
[INPUT SELECT BUTTON]  button,  button,  
button,  button,  button, 
 button  button,  button,  
button,  button,  button, 
 button,  button,  
button,  button
[MENU BUTTON]  button
[LENS BUTTON]  button Lens buttons (, , )
[AUTO SETUP BUTTON]  button
[SHUTTER BUTTON]  button
[ASPECT BUTTON] ― button
[ON SCREEN BUTTON] ― button
[OTHER BUTTON] asqw,  button Buttons not listed above
8) Press 
qw to switch the item.
[ENABLE] Enables button operations.
[DISABLE] Disables button operations.
 fFollowing items can be selected only when [SDI BUTT ON] in [INPUT SELECT BUTTON] is selected.
[TOGGLE]Switches between [SDI1] and [SDI2] when the button is operated.
[SDI1] Fixes to [SDI1].
[SDI2] Fixes to [SDI2].
[DISABLE] Disables button operations.
 fPress the  button to return to the  [CONTROL PANEL] screen or the [REMOTE CONTROL]  
screen when [INPUT SELECT BUTTON] is selected in Step 7).
9)
 
Press 
 as to select [APPLY], and press the  button.
 fThe confirmation screen is displayed.
10)

 
Press 
 qw to select [OK], and press the  button.
Note
 f When a button operation is performed on the device set to [DISABLE], the  [CONTROL  DEVICE PASSWORD] screen is displayed.
Enter the control device password.
 f The 

[CONTROL DEVICE PASSWORD] screen will disappear when there is no operation for approx. 10 seconds.
 fIf the operations of both [CONTROL

 PANEL] and [REMOTE CONTROL] are set to [DISABLE], the projector cannot be turned off (cannot 
enter standby).
 f When the setting has completed, the menu screen will disappear

. To operate continuously, press the  button to display the main 
menu.
 f Even when you set button operations on the remote control disabled, operations of the  and  buttons on the remote 
control are kept enabled.
[CONTROL DEVICE PASSWORD CHANGE]
The control device password can be changed.
1)
 
Press 
 as to select [CONTROL DEVICE PASSWORD CHANGE].
2)
 
Press the  button.
 fThe 

[CONTROL DEVICE PASSWORD CHANGE]  screen is displayed.
3)
 
Press 
 asqw to select the text, and press the  button to enter the text.  
						

							Chapter 4 Settings — [SECURITY] menu
ENGLISH - 155
4) Press asqw to select [OK], and press the  button.
 fT

o cancel, select [CANCEL].
Attention
 f The initial password is “AAAA” by the factory default or when [ALL  USER DA TA] in [INITIALIZE] (x   page   144) is executed. fChange the password periodically that is hard to guess.  
						

							Chapter 4 Settings — [NETWORK] menu
156 - ENGLISH
[NETWORK] menu
On the menu screen, select [NETWORK] from the main menu, and select an item from the sub-menu.
Refer to “Navigating through the menu” (x
  page   76) for the operation of the menu screen.
[DIGITAL LINK MODE]
Switch the communication method of the  terminal of the projector.
1)
 
Press 
 as to select [DIGITAL LINK MODE].
2)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[AUTO] Switches the communication method automatically to DIGITAL LINK, long reach, or Ethernet.
[DIGITAL LINK] Fixes the communication method to DIGITAL LINK.
[LONG REACH] Fixes the communication method to long reach.
[ETHERNET] Fixes the communication method to Ethernet.
Possible communication modes
l: Communication possible
―: Communication not possible
Setting Communication possible
Video transfer 
(100
  m (328'1"))Video transfer 
(150
  m (492'2"))Ethernet RS
- 232C
[AUTO] For DIGITAL LINK
l―
ll
For long reach ―
lll
For Ethernet ――
l
*1―
[DIGITAL LINK] l―
ll
[LONG REACH] ―
lll
[ETHERNET] ――
l
*1―
*1 Communication via a twisted-pair-cable transmitter is not available. Con\
nect the projector to the network directly .
Note
 fThe maximum transmission distance when connected with the long-reach communication method is 150   m (492'2"). However, the signal 
that the projector can receive is only up to 1080/60p (148.5   MHz).
 fWhen the communication method of the twist-pair-cable transmitter is set\
 to long reach, the projector will connect with long-reach 
communication method when [DIGIT

AL LINK MODE] is set to [AUTO]. To connect with the optional DIGITAL LINK Switcher (Model No.: 
ET
-

YFB200G) with the long-reach communication method, set [DIGITAL LINK MODE] to [LONG REACH].
 fConnection will not be made correctly if the twist-pair-cable transmitte\
r is not supporting the long-reach communication method even if 
[DIGIT

AL LINK MODE] is set to [LONG REACH].
[DIGITAL LINK SETUP]
Set the communication method of DIGITAL LINK or Ethernet.
When the projector is connected directly via Ethernet
1) Press  as to select [DIGITAL LINK SETUP].
2)  
Press the  button.
 fThe 

[DIGITAL LINK SETUP] screen is displayed.
3)
 
Press 
 as to select [DUPLEX(ETHERNET)].
4)
 
Press 
 qw to switch the communication method.
 fThe items will switch each time you press the button.
[AUTONEGOTIATION] Sets the communication method automatically.
[100BaseTX-Full] Sets full-duplex communication method.
[100BaseTX-Half] Sets half-duplex communication method.  
						

							Chapter 4 Settings — [NETWORK] menu
ENGLISH - 157
5) Press as to select [STORE].
6)  
Press the  button.
7)

 
When the confirmation screen is displayed, press  qw

 to select [OK], and then press the  
button.
Note
 f The projector does not support 10BaseT  Full/Half.
When the projector is connected to a twisted-pair-cable transmitter
1) Press as to select [DIGITAL LINK SETUP].
2)  
Press the  button.
 fThe 

[DIGITAL LINK SETUP] screen is displayed.
3)
 
Press 
 as to select [DUPLEX(DIGITAL LINK)].
4)
 
Press 
 qw to switch the communication method.
 fThe items will switch each time you press the button.
[100BaseTX-Full] Sets full-duplex communication method.
[100BaseTX-Half] Sets half-duplex communication method.
[AUTONEGOTIATION] Sets the communication method automatically.
5) Press as to select [STORE].
6)  
Press the  button.
7)

 
When the confirmation screen is displayed, press  qw

 to select [OK], and then press the  
button.
[DIGITAL LINK STATUS]
Display the DIGITAL LINK connection environment.
1)
 
Press 
 as to select [DIGITAL LINK STATUS].
2)
 
Press the  button.
 fThe 

[DIGITAL LINK STATUS] screen is displayed.
[LINK STATUS] Either [NO LINK], [DIGITAL LINK], [LONG REACH], or [ETHERNET] is displayed.
[HDCP STATUS] Either [NO SIGNAL], [OFF], or [ON] is displayed.
[SIGNAL QUALITY] [SIGNAL QUALITY] is a numerical value of the amount of error, and the display color changes to 
green, yellow, or red depending on that value.
Check the signal quality level while receiving a signal from the twisted-pair-cable transmitter
.
 f[MAX]/[MIN]: Maximum/minimum value of the amount of error
 fGreen (-12 dB or lower)  →  normal signal quality level.
 fY

ellow (
-11 to -8 dB) → caution level that noise may appear on the screen.
 f Red (-7 dB or higher)  →  abnormal level with interrupted synchronization and receiving not 
possible.
[NETWORK SETUP]
Perform the initial setting of the network before using the network func\
tion.
1)
 
Press 
 as to select [NETWORK SETUP].
2)
 
Press the  button.
 fThe 

[NETWORK SETUP] screen is displayed.
3)
 
Press 
 as to select an item, and change the settings according to the operation instructions of the 
menu.
[PROJECTOR NAME] Allows to change the projector name. Enter the host name if it is required to use a DHCP  server.  
						

							Chapter 4 Settings — [NETWORK] menu
158 - ENGLISH
[DHCP][ON]
If a DHCP server exists in the network where the projector is to be 
connected, obtains the IP address automatically.
[OFF] If a DHCP server does not exist in the network where the projector 
is to be connected, set [IP ADDRESS], [SUBNET MASK], and 
[DEFAULT GATEWAY].
[IP ADDRESS] Enter the IP address when a DHCP server is not used.
[SUBNET MASK] Enter the subnet mask when a DHCP server is not used.
[DEFAULT GATEWAY] Enter the default gateway address when a DHCP server is not used.
4) Press as to select [STORE], and press the  button.
5)  
When the confirmation screen is displayed, press  qw

 to select [OK], and press the  button.
Note
 f When using a DHCP  server, confirm that the DHCP server is running. fConsult your network administrator regarding the IP
 address, subnet mask, and default gateway.
 fWhen [Art-Net SETUP] is set to [ON(2.X.X.X)] or [ON(10.X.X.X)], [NETWORK SETUP] cannot be selected.
[NETWORK CONTROL]
Set up the control method of the network.
1)
 
Press 
 as to select [NETWORK CONTROL].
2)
 
Press the  button.
 fThe 

[NETWORK CONTROL] screen is displayed.
3)
 
Press 
 as to select an item, and press qw to change the setting.
[WEB CONTROL] Set to [ON] to control with the web browser.
[PJLink CONTROL] Set to [ON] to control with the PJLink protocol.
[COMMAND CONTROL] Set to [ON] to control with the / terminal control command format 
(x
  page   202). Refer to “Control commands via LAN” ( x
  page   196).
[COMMAND PORT] Set the port number used for command control.
[Crestron Connected(TM)] Set to [ON] to control with Crestron Connected
TM of Crestron Electronics, Inc.
[AMX D.D.] Set to [ON] to control with the controller of AMX Corporation.
Setting this function to [ON] enables detection through “AMX Device Discovery”. For details, visit the 
website of AMX Corporation.
URL http://www.amx.com/
[EXTRON XTP] Set to [ON] when connecting the “XTP transmitter” of Extron Electronics to the  
terminal.
The [EXTRON XTP] setting must be set to [OFF] when connecting the optional DIGIT
AL LINK output 
supported device (Model No.: ET
-

YFB100G, ET
-

YFB200G).
For details of the “XTP transmitter”, visit the website of Extron Electronics.
URL http://www.extron.com/
4) Press  as to select [STORE], and press the  button.
5)  
When the confirmation screen is displayed, press  qw

 to select [OK], and press the  button.
[NETWORK STATUS]
Display the status of the projector network.
1) 
Press 
 as to select [NETWORK STATUS].
2)
 
Press the  button.
 fThe 

[NETWORK STATUS] screen is displayed.
[DHCP] Displays the status of use of the DHCP server.
[IP ADDRESS] Displays the [IP ADDRESS].
[SUBNET MASK] Displays the [SUBNET MASK].
[DEFAULT GATEWAY] Displays the [DEFAULT GATEWAY].
[DNS1] Displays the address of the preferred DNS server.
[DNS2] Displays the address of the alternate DNS server.
[MAC ADDRESS] Displays the [MAC ADDRESS].  
						

							Chapter 4 Settings — [NETWORK] menu
ENGLISH - 159
[DIGITAL LINK MENU]
When the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET- YFB200G) is connected 
to the  terminal, the main menu of the connected DIGITAL LINK output supported device is 
displayed. Refer to the Operating Instructions of the DIGITAL LINK output supported device for details.
Note
 f [DIGITAL LINK MENU] cannot be selected when [EXTRON XTP] is set to [ON]. fThe operation guidance for the “RETURN” button is in the menu screen of the Digital Interface Box and DIGIT AL
 LINK Switcher. The 
projector does not have the “RETURN” button, but the same operation is available with the  button.
[Art-Net SETUP]
Make settings to use the Art-Net function.
1)
 
Press 
 as to select [Art-Net SETUP].
2)
 
Press 
 qw to select an item.
 fThe items will switch each time you press the button.
[OFF] Disables the Art-Net function.
[ON(2.X.X.X)] Enables the Art-Net function and sets the IP address to 2.X.X.X.
[ON(10.X.X.X)] Enables the Art-Net function and sets the IP address to 10.X.X.X.
[ON(MANUAL)] Enables the Art-Net function and uses the IP address set in [NETWORK SETUP].
 fWhen other than [OFF] is selected, proceed to Step  3).
3)
 
Press the  button.
 f The 

[Art-Net SETUP] screen is displayed.
4)
 
Press 
 as to select an item, and press qw to switch the setting.
[NET] Enter [NET] to be used when the projector processes Art-Net.
[SUB NET] Enter [SUB NET] to be used when the projector processes Art-Net.
[UNIVERSE] Enter [UNIVERSE] to be used when the projector processes Art-Net.
[START ADDRESS] Enter [START ADDRESS] to be used when the projector processes Art-Net.
5) Press as to select [STORE], and press the  button.
6)  
When the confirmation screen is displayed, press  qw

 to select [OK], and press the  button.
Note
 f If [ON(2.X.X.X)] or [ON(10.X.X.X)] is selected, IP  address is calculated and set automatically.
[Art-Net CHANNEL SETTING]
Set the assignment of the channel.
For the channel definitions used for controlling the projector with the  Art-Net function, refer to “Using Art-Net 
function” (x
  page   193).
1)
 
Press 
 as to select [Art-Net CHANNEL SETTING].
2)
 
Press 
 qw to switch the item.
[2] Uses the channel assignment in standard setting.
[USER] Changes the channel assignment.
[1] Uses the channel assignment with DZ21K series compatible.
DZ21K series: DZ21K series, DS20K series, DW17K series, DZ16K series
 f
When [2] or [1] is selected, pressing the  button displays the function assigned to the channel.
 fWhen [USER] is selected, proceed to Step  3)

.
3)
 
Press the  button.
 f The 

[Art-Net CHANNEL SETTING]  screen is displayed.
4)
 
Press 
 as to select the channel to set, and pressqw to switch the item.  
						

							Chapter 4 Settings — [NETWORK] menu
160 - ENGLISH
[LIGHT OUTPUT]Adjusts the amount of light.
[INPUT SELECT] Switches the input.
[LENS POSITION] Moves the lens position.
[LENS H SHIFT] Adjusts the lens shift in the horizontal direction.
[LENS V SHIFT] Adjusts the lens shift in the vertical direction.
[LENS FOCUS] Adjusts the focus.
[LENS ZOOM] Adjusts the zoom.
[POWER] Controls the power status.
[SHUTTER] Controls the shutter.
[GEOMETRY] Performs geometric adjustment.
[CUSTOM MASKING] Performs geometric adjustment using the computer.
To use PC-1, PC-2, and PC-3, the optional Upgrade Kit (Model No.: ET
-

UK20) is required.
[FREEZE] Freezes the projected image.
[COLOR] Adjusts the color saturation.
[TINT] Adjusts the tint.
[RASTER PATTERN] Displays the raster pattern.
[ENABLE/DISABLE] Enables/disables the control of the projector with the Art-Net function.
[NONE] No definition
 fThe setting can be also made by pressing  as  to select the channel, pressing the  button to 
display the item list, pressing  asqw to select the item, and pressing the  button.
 fSame item cannot be set for multiple channels, except for [NONE].
[Art-Net STATUS]
Display the content of control assigned to each channel and the received\
 data of that channel.
1)
 
Press 
 as to select [Art-Net STATUS].
2)
 
Press the  button.
 fThe 

[Art-Net STATUS] screen is displayed.
Network connection
The projector has a network function, and the following operations are a\
vailable from the computer using the web 
control.
 fSetting and adjustment of the projector
 fDisplay of the projector status
 fSending E-mail messages when there is a problem with the projector
The projector supports “Crestron Connected
TM”, and the following application software of Crestron Electronics, 
Inc. can be used.
 f RoomV

iew Express
 f Fusion R

V
 f RoomV

iew Server Edition
Attention
 f When a LAN cable is directly connected to the projector , the network connection must be made indoors.
Note
 f“Crestron ConnectedTM” is a system of Crestron Electronics, Inc. that collectively manages and controls devices on multiple systems 
connected to a network using a computer.
 f For details of the “Crestron ConnectedTM”, visit the website of Crestron Electronics, Inc. (English only .)
URL http://www.crestron.com
Download “RoomView Express” from the Crestron Electronics, Inc. website. (English only.)
URL http://www.crestron.com/getroomview
 f A

 LAN cable is required to use the network function.