Panasonic Projector PT-RZ475U User Manual

							Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 91
Setting the audio output during standby
1) Press as to select [AUDIO SETTING].
2)  
Press the  button.
 f The  [AUDIO SETTING]  screen is displayed.
3) Press as to select [IN STANDBY MODE].
4)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Turns off audio output during standby.
[ON] Turns on audio output during standby.
Note
 fWhen [STANDBY MODE] ( x   page   80) in the [PROJECTOR SETUP] menu → [ECO MANAGEMENT] is set to [ECO], audio cannot be 
output during standby.
 f The projector has no built-in speakers. 
Audio can be output via external audio systems connected to the audio ou\
tput terminal.
Setting audio input when HDMI input is selected
1) Press  as to select [AUDIO SETTING].
2)  
Press the  button.
 f The  [AUDIO SETTING]  screen is displayed.
3) Press as to select [HDMI].
4)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[HDMI AUDIO] Outputs HDMI audio.
[AUDIO IN] Outputs audio connected via the  terminal.
Note
 fIf COMPUTER, DVI - I, or VIDEO input is selected, audio connected to the  termina\
l is output.
Setting audio input when DIGITAL LINK input is selected
1) Press as to select [AUDIO SETTING].
2)  
Press the  button.
 f The  [AUDIO SETTING]  screen is displayed.
3) Press as to select [DIGITAL LINK].
4)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[DIGITAL LINK AUDIO] Outputs DIGITAL LINK audio.
[AUDIO IN] Outputs audio connected via the  terminal.
Note
 fIf COMPUTER, DVI - I, or VIDEO input is selected, audio connected to the  termina\
l is output.  
						

							Chapter 4 Settings — [PROJECTOR SETUP] menu
92 - ENGLISH
[STATUS]
Display the status of the projector.
1) Press as to select [STATUS].
2)  
Press the  button.
 f The  [STATUS] screen is displayed.
3) Press  qw to switch the pages.
 fThe page will change each time you press the button.
[INPUT] Displays the input terminal currently selected.
[SIGNAL NAME] Displays the input signal name.
[SIGNAL FREQUENCY] Displays the frequency of the input signal.
[PROJECTOR RUNTIME] Displays the operation times of the projector.
[INTAKE AIR TEMP.] Displays the status of the air intake temperature of the projector.
[OPTICS MODULE TEMP.] Displays the status of the internal temperature of the projector.
[NUMBER OF ENTRY  SIGNAL] Displays the number of registered signals.
[EMULATE] Displays the [EMULATE] settings.
[PROJECTOR TYPE] Displays the type of the projector.
[SERIAL NUMBER] Displays the serial number of the projector.
[MAIN VERSION] Displays the main version of the firmware of the projector.
[SUB VERSION] Displays the sub version of the firmware of the projector.
[NETWORK VERSION] Displays the network version of the projector.
Note
 fThe content of status can be sent via E-mail by pressing the  but\
ton while displaying the  [ST ATUS] screen.
[DATE AND TIME]
Set the time zone, date, and time of the built-in clock of the projector\
.
Setting the time zone
1) Press as to select [DATE AND TIME].
2)  
Press the  button.
 f The  [DATE AND TIME] screen is displayed.
3) Press  as to select [TIME ZONE].
4)  
Press 
 qw to switch the item.
Setting the date and time manually
1) Press as to select [DATE AND TIME].
2)  
Press the  button.
 f The  [DATE AND TIME] screen is displayed.
3) Press  as to select [ADJUST CLOCK].
4)  
Press the  button.
 f The  [ADJUST CLOCK] screen is displayed.
5) Press  as to select an item, and press qw to set the local date and time.
6)  
Press 
 as to select [APPLY], and press the  button.
 fThe setting of the time will be completed.  
						

							Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 93
Setting the date and time automatically
1) Press as to select [DATE AND TIME].
2)  
Press the  button.
 f The  [DATE AND TIME] screen is displayed.
3) Press  as to select [ADJUST CLOCK].
4)  
Press the  button.
 f The  [ADJUST CLOCK] screen is displayed.
5) Press  as to select [NTP SYNCHRONIZATION], and press qw to change the setting to [ON].
 fThe items will switch each time you press the button.
[OFF] Disables [NTP SYNCHRONIZATION].
[ON] Enables [NTP SYNCHRONIZATION].
6) Press as to select [APPLY], and press the  button.
 fThe setting of the time will be completed.
Note
 fTo set the date and time automatically, the projector must be connected to the network. fIf synchronization with the NTP
 server fails just after [NTP SYNCHRONIZATION] is turned [ON], or if [NTP SYNCHRONIZATION] is turned 
[ON] while the NTP server is not set, [NTP SYNCHRONIZATION] will return to [OFF].
 f Access the projector via a web browser to set the NTP

 server. Refer to “[Adjust clock] page” (x   page   109) for details.
[SAVE ALL USER DATA]
Save the various setting values as a backup in the built-in memory of th\
e projector.
1) Press as to select [SAVE ALL USER DATA].
2)  
Press the  button.
 f The  [SECURITY PASSWORD] screen is displayed.
3) Enter a security password and press the  button.
4)  
When the confirmation screen is displayed, press  qw

 to select [OK], and press the  button.
 f[PROGRESS] is displayed while saving data.
Note
 fThe image setting registered in [USER LOGO] is not saved.
[LOAD ALL USER DATA]
Load the various setting values saved as a backup in the built-in memory\
 of the projector.
1) Press  as to select [LOAD ALL USER DATA].
2)  
Press the  button.
 f The  [SECURITY PASSWORD] screen is displayed.
3) Enter a security password and press the  button.
4)  
When the confirmation screen is displayed, press  qw

 to select [OK], and press the  button.
Note
 f The projector will go into the standby status to reflect the setting values when [LOAD  ALL  USER DATA] is executed.  
						

							Chapter 4 Settings — [PROJECTOR SETUP] menu
94 - ENGLISH
[INITIALIZE]
Return various setting values to their factory default settings.
1) Press as to select [INITIALIZE].
2)  
Press the  button.
 f The  [SECURITY PASSWORD] screen is displayed.
3) Enter a security password and press the  button.
 fThe  [INITIALIZE]  screen is displayed.
4) Press as to select an item to initialize.
[ALL USER DATA] Returns all setting items including [ENTRY SIGNAL], [NETWORK SETUP], [E-mail set up], and 
[USER LOGO] to factory default settings.
The projector will go into the standby status to reflect the setting values.
[ENTRY SIGNAL] Deletes all the setting values saved for each input signal.
To delete only a part of a registered signal, perform the procedure descr\
ibed in “Deleting the 
registered signal” (
x
  page   120).
[NETWORK/E
- MAIL]Returns [NETWORK SETUP] and [E-mail set up] to factory default settings.\
[LOGO IMAGE] Deletes the image registered in [USER LOGO].
5) Press the  button.
6)  
When the confirmation screen is displayed, press  qw

 to select [OK], and press the  button.
[SERVICE PASSWORD]
This function is used by a service person.  
						

							Chapter 4 Settings — [TEST PATTERN] menu
ENGLISH - 95
[TEST PATTERN] menu
On the menu screen, select [TEST PATTERN] from the main menu.
Refer to “Navigating through the menu” (x
  page   46) for the operation of the menu screen.
 fPress 

qw to switch.
[TEST PATTERN]
Display the test pattern built-in to the projector.
Settings of position, size, and other factors will not be reflected in test patterns. Make sure to display the input signal before performing various 
adjustments.
1) Press  qw to switch the [TEST PATTERN] item.
 fThe items will switch each time you press the button.
Menu screen + All white
Displays test patterns with the menu screen. Select a test pattern so th\
at it is easy to make various 
adjustments.
Menu screen + All black
Menu screen + Window
Menu screen + Window  (inversion)
Menu screen + Color bar  (vertical)
Menu screen + Color bar  (horizontal)
Menu screen + 16:9/4:3  aspect frame
Menu screen + Focus
Menu screen + Entry screen Displays the menu screen and input signal.
Built-in test patterns are not displayed.
Note
 f
Press the  button while the test pattern is displayed to hide the \
on-screen menu. fIf the on-screen display is hidden while displaying the test pattern, th\
e test pattern is not switched even if  qw
 are pressed. To switch the test 
pattern, operate with the on-screen displayed.  
						

							Chapter 4 Settings — [SECURITY] menu
96 - ENGLISH
[SECURITY] menu
On the menu screen, select [SECURITY] from the main menu, and select an \
item from the sub-
menu.
Refer to “Navigating through the menu” (x
  page   46) for the operation of the menu screen.
 fWhen the projector is used for the first time
Initial password: Press  awsqawsq in order

, and press the  button.
 fAfter selecting the item, press 

asqw to set.
Attention
 fWhen you select the [SECURITY] menu and press the  button, entering a password is required. Enter the preset password and 
then continue operations of the [SECURITY] menu.
 fWhen the password has been changed previously

, enter the changed password, and press the  button.
Note
 fThe entered password is displayed with * mark on the screen. fAn error message is displayed on the screen when the entered password is\
 incorrect. Re-enter the correct password.
[SECURITY PASSWORD]
The [SECURITY PASSWORD] screen is displayed when the power is turned on. If an incorrect passwo\
rd has been entered, operations other 
than the power  button and the  button are not available.
1) Press  as to select [SECURITY PASSWORD].
2)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Disables the security password entry.
[ON] Enables the security password entry.
Note
 f[SECURITY  PASSWORD] is set to [OFF] at the time of purchase or when [ALL USER DATA] has been initialized. fChange the password periodically that is hard to guess. fThe security password is enabled after setting [SECURITY

 PASSWORD] to [ON] and turning the  switch to .
[SECURITY PASSWORD CHANGE]
Change the security password.
1) Press as to select [SECURITY PASSWORD CHANGE].
2)  
Press the  button.
 f The  [SECURITY PASSWORD CHANGE] screen is displayed.
3) Press  asqw and the number ( - ) buttons to set the password.
 fUp to eight button operations can be set.
4) Press the  button.
5)  
Re-enter the password for the confirmation.
6)

 
Press the  button.
Note
 f The entered password is displayed with * mark on the screen. fIf numbers have been used for the security password, the security passwo\
rd will need to be initialized again if the remote control is lost. 
Consult your dealer for the initialization method.  
						

							Chapter 4 Settings — [SECURITY] menu
ENGLISH - 97
[TEXT DISPLAY]
Overlap the security message (text) over the projected image.
1) Press as to select [TEXT DISPLAY].
2)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Hides the security message.
[ON] Displays the security message.
Note
 fIf a closed caption signal of the selected mode is input, the security m\
essage is not displayed.
[TEXT CHANGE]
Change the text displayed when [TEXT DISPLAY] is set to [ON].
1) Press  as to select [TEXT CHANGE].
2)  
Press the  button.
 f The  [TEXT CHANGE] screen is displayed.
3) Press  asqw to select the text, and press the  button to enter the text.
 fUp to 22 characters can be input.
4) Press  asqw to select [OK], and press the  button.
 fThe text is changed.
[MENU LOCK]
Display the menu with the  button, and set whether to enable menu \
operations.
1) Press  as to select [MENU LOCK].
2)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Cancels the lock on menu operations.
[ON] Locks menu operations.
Note
 fAfter setting [MENU LOCK] to [ON], the  button cannot be operated \
if the incorrect password is input. f[MENU LOCK] is set to [OFF] at the time of purchase or when [ALL
 USER DATA] has been initialized.
 fThe lock release is maintained until the projector enters standby

.
[MENU LOCK PASSWORD]
Change the menu lock password.
1) Press as to select [MENU LOCK PASSWORD].
2)  
Press the  button.
 f The  [MENU LOCK PASSWORD] screen is displayed.
3) Press  asqw to select the text, and press the  button to enter the text.
 fUp to 16 characters can be input.
4) Press  asqw to select [OK], and press the  button.
 fTo cancel, select [CANCEL].
Attention
 fThe initial password is “AAAA” at the time of purchase or when [ALL  USER DA TA] has been initialized. fChange the password periodically that is hard to guess.  
						

							Chapter 4 Settings — [SECURITY] menu
98 - ENGLISH
[CONTROL DEVICE SETUP]
Enable/disable the button operations on the control panel and the remote\
 control.
1) Press as to select [CONTROL DEVICE SETUP].
2)  
Press the  button.
 f The  [CONTROL DEVICE SETUP] screen is displayed.
3) Press  as to select [CONTROL PANEL] or [REMOTE CONTROL].
[CONTROL PANEL] Sets the limitation on the control from the control panel.
[REMOTE CONTROL] Sets the limitation on the control from the remote control.
4) Press the  button.
 fThe  [CONTROL PANEL] screen or the [REMOTE CONTROL] screen is displayed.
5) Press  as to select [ENABLE] or [DISABLE].
 fYou can set the operation restriction from the control panel or the remot\
e control.
[ENABLE] Enables all button operations on the projector body or the remote contro\
l.
[DISABLE] Disables all button operations on the projector body or the remote contr\
ol.
6) Press the  button.
 fThe confirmation screen is displayed.
7) Press  qw to select [OK], and press the  button.
Note
 f When a button operation is performed on the device set to [DISABLE], the\
  [SECURITY  PASSWORD] screen is displayed.
To continue operations, enter the security password.
 f The 

[SECURITY PASSWORD] screen will disappear when the  button is pressed, or when there \
is no operation for approximately 
ten seconds.
 f If the operations of both [CONTROL

 PANEL] and [REMOTE CONTROL] are set to [DISABLE], the projector cannot be turned off (cannot 
enter standby).
 f When the setting has completed, the menu screen will disappear

. To operate continuously, press the  button to display the main 
menu.  
						

							Chapter 4 Settings — [NETWORK] menu
ENGLISH - 99
[NETWORK] menu
On the menu screen, select [NETWORK] from the main menu, and select an i\
tem from the sub-
menu.
Refer to “Navigating through the menu” (x
  page   46) for the operation of the menu screen.
 fAfter selecting the item, press 

asqw to set.
[DIGITAL LINK MODE]
Switch the communication method of the  terminal of the projector.
1) Press  as to select [DIGITAL LINK MODE].
2)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[AUTO] Switches the communication method automatically to DIGITAL LINK or Ethernet.
[DIGITAL LINK] Fixes the communication method to DIGITAL LINK.
[ETHERNET] Fixes the communication method to Ethernet.
Possible communication modes
Setting Communication possible
HDMI Ethernet RS
- 232C
[AUTO] For DIGITAL LINK
lll
For Ethernet ―
l―
[DIGITAL LINK] lll
[ETHERNET] ―
l―
l: Communication possible
―: Communication not possible
[DIGITAL LINK SETUP]
Set the communication method of DIGITAL LINK.
When the projector is connected directly via Ethernet
1) Press  as to select [DIGITAL LINK SETUP].
2)  
Press the  button.
 f The  [DIGITAL LINK SETUP] screen is displayed.
3) Press  as to select [DUPLEX(ETHERNET)].
4)  
Press 
 qw to switch the communication method.
 fThe items will switch each time you press the button.
[AUTONEGOTIATION] The communication method is set automatically.
[100BaseTX - Full]Full-duplex communication method is set.
[100BaseTX
- Half]Half-duplex communication method is set.
5) Press as to select [STORE].
6)  
Press the  button.
7)

 
When the confirmation screen is displayed, press  qw

 to select [OK], and press the  button.  
						

							Chapter 4 Settings — [NETWORK] menu
100 - ENGLISH
Note
 fThe projector does not support 10BaseT  Full/Half.
When the projector is connected to a twisted-pair-cable transmitter
1) Press as to select [DIGITAL LINK SETUP].
2)  
Press the  button.
 f The  [DIGITAL LINK SETUP] screen is displayed.
3) Press  as to select [DUPLEX(DIGITAL LINK)].
4)  
Press 
 qw to switch the communication method.
 fThe items will switch each time you press the button.
[100BaseTX-Full] Full duplex communication method is set.
[100BaseTX - Half]Half-duplex communication method is set.
[AUTONEGOTIATION] The communication method is set automatically.
5) Press as to select [STORE].
6)  
Press the  button.
7)

 
When the confirmation screen is displayed, press  qw

 to select [OK], and press the  button.
[DIGITAL LINK STATUS]
Display DIGITAL LINK connection environment.
1) Press as to select [DIGITAL LINK STATUS].
2)  
Press the  button.
 f The  [DIGITAL LINK STATUS] screen is displayed.
[LINK STATUS] Either [NO LINK], [DIGITAL LINK], or [ETHERNET] is displayed.
[HDMI STATUS] Either [NO HDMI], [HDMI ON], or [HDCP ON] is displayed.
[SIGNAL QUALITY] [SIGNAL QUALITY] is a numerical value of the amount of error, and the display color changes to 
green, yellow, or red depending on that value.
Check the signal quality level while receiving a signal from the twisted-pair-cable transmitter
.
 fMAX/MIN: Maximum/minimum value of the amount of error

.
 fGreen (-12 dB or lower)  →  Normal signal quality level.
 fY

ellow (
-11 to -8 dB) → Warning level where there is the possibility of noise introduced on the 
screen.
 f Red (-7 dB or higher) → Abnormal level where synchronization may be interrupted, or a signal may 
not be received.
[NETWORK SETUP]
Perform the initial setting of the network before using the network func\
tion.
1) Press  as to select [NETWORK SETUP].
2)  
Press the  button.
 f The  [NETWORK SETUP] screen is displayed.
3) Press  as to select an item, and change the settings according to the operation i\
nstructions of the 
menu.
[PROJECTOR NAME] Change the setting when using a DHCP server.
[DHCP] Set to [ON] when obtaining an IP address automatically using a DHCP server. Set to [OFF] when not 
using a DHCP server.
[IP ADDRESS] Enter the IP address when not using a DHCP server.
[SUBNET MASK] Enter the subnet mask when not using a DHCP server.
[DEFAULT GATEWAY] Enter the default gateway address when not using a DHCP server.
4) Press as to select [STORE], and press the  button.