Panasonic Projector PT-RZ475U User Manual

							Chapter 4 Settings — [NETWORK] menu
ENGLISH - 111
[Authentication set up] page
Set the authentication items when POP authentication or SMTP authentication is necessary to send an E-mail.
Click [Detailed set up] → [Authentication set up].
1
2
3
4
5
6
7
8
1 [Auth]
Select the authentication method specified by your Internet 
service provider
.
2
 
[SMTP
  Auth]
Set when the SMTP authentication is selected.
3
 
[POP
  server name]
Enter the POP server name.
Allowed characters:
Alphanumerics (A to Z, a to z, 0 to 9)
Minus sign (-) and period (.)
4
 
[User name]
Enter the user name for the POP

 server or the SMTP server. 5
 [Password]
Enter the password for the POP
 server or the SMTP server.
6
 
[SMTP
  server port]
Enter the port number of the SMTP server.
(Normally 25)
7
 
[POP
  server port]
Enter the port number of the POP server.
(Normally 110)
8
 
[Submit]
Update the settings.  
						

							Chapter 4 Settings — [NETWORK] menu
112 - ENGLISH
Contents of E-mail sent
Example of E-mail sent when E-mail is set
The following E-mail is sent when the E-mail settings have been establis\
hed.
=== Panasonic projector report(CONFIGURE) ===
Projector Type : RZ475
Serial No  : SW1234567
-----  E-mail setup data -----
TEMPERATURE WARNING SETUP
MINIMUM TIME             at  [  60] minutes interval
INTAKE AIR TEMPERATURE   Over [    46 degC /   114 degF ] 
ERROR  [ ON  ]
INTAKE AIR TEMPERATURE  [ OFF ]
PERIODIC REPORT
Sunday  [ ON  ]  Monday  [ ON  ]  Tuesday  [ ON  ]  Wednesday  [ ON  ]
Thursday  [ ON  ]  Friday  [ ON  ]  Saturday  [ ON  ]
00:00  [ ON  ]  01:00  [ ON  ]  02:00  [ ON  ]  03:00  [ ON  ]
04:00  [ ON  ]  05:00  [ ON  ]  06:00  [ ON  ]  07:00  [ ON  ]
08:00  [ ON  ]  09:00  [ ON  ]  10:00  [ ON  ]  11:00  [ ON  ]
12:00  [ ON  ]  13:00  [ ON  ]  14:00  [ ON  ]  15:00  [ ON  ]
16:00  [ ON  ]  17:00  [ ON  ]  18:00  [ ON  ]  19:00  [ ON  ]
20:00  [ ON  ]  21:00  [ ON  ]  22:00  [ ON  ]  23:00  [ ON  ]
-----  check system -----
MAIN CPU BUS  [   OK    ]
FAN  [   OK    ]
INTAKE AIR TEMPERATURE  [   OK    ]
OPTICS MODULE TEMPERATURE  [   OK    ]
INTERNAL AIR TEMPERATURE  [   OK    ]
LIGHT STATUS  [   OK    ]
INTAKE AIR TEMP.SENSOR  [   OK    ]
OPTICS MODULE TEMP.SENSOR  [   OK    ]
INTERNAL AIR TEMP.SENSOR  [   OK    ]
BATTERY  [   OK    ]
PHOSPHOR WHEEL  [   OK    ]
(Error code  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00)
Intake air temperature  :[    18 degC /    64 degF ]
Optics module temperature  :[    30 degC /    86 degF ]
Internal air temperature  :[    28 degC /    82 degF ]
PROJECTOR RUNTIME  9 H
--------  Current status --------
MAIN VERSION  1.00
NETWORK VERSION  1.00
SUB VERSION  1.00
POWER STATUS  POWER=STANDBY
INPUT SIGNAL  DVI-I
SIGNAL NAME  XGA60
SIGNAL FREQUENCY  48.36kHz / 60.00H
----- Wired Network configuration -----
DHCP Client  OFF
IP address  192.168.0.8
MAC address  04:20:9A:00:00:00
Mon Jul 05 14:11:29 2012
----- Memo -----  
						

							Chapter 4 Settings — [NETWORK] menu
ENGLISH - 113
Example of the E-mail sent for an error
The following E-mail is sent when an error has occurred.
=== Panasonic projector report(ERROR) ===
Projector Type  : RZ475
Serial No  : SW1234567
-----  check system -----
MAIN CPU BUS [   OK    ]
FAN  [   OK    ]
INTAKE AIR TEMPERATURE  [   OK    ]
OPTICS MODULE TEMPERATURE  [   OK    ]
INTERNAL AIR TEMPERATURE  [   OK    ]
LIGHT STATUS  [   OK    ]
INTAKE AIR TEMP.SENSOR  [   OK    ]
OPTICS MODULE TEMP.SENSOR  [ FAILED  ]
INTERNAL AIR TEMP.SENSOR  [   OK    ]
BATTERY  [   OK    ]
PHOSPHOR WHEEL  [   OK    ]
(Error code  00 00 00 00 00 00 00 00 00 00 00 02 00 00 00 00)
Intake air temperature  :[    18 degC /    64 degF ]
Optics module temperature  :[    30 degC /    86 degF ]
Internal air temperature  :[    28 degC /    82 degF ]
PROJECTOR RUNTIME  9 H
--------  Current status --------
MAIN VERSION  1.00
NETWORK VERSION  1.00
SUB VERSION  1.00
POWER STATUS  POWER=STANDBY
INPUT SIGNAL  DVI-I
SIGNAL NAME  XGA60
SIGNAL FREQUENCY  48.36kHz / 60.00H
----- Wired Network configuration -----
DHCP Client  OFF
IP address  192.168.0.8
MAC address  04:20:9A:00:00:00
Mon Jul 05 14:11:29 2012
----- Memo -----
[ECO management set up] page
You can perform settings for the ECO management function of the projector\
.
Click [Detailed set up]  → [ECO management set up].
1
2
3
4
5
6
7
1 [LIGHT POWER]
Select the light source power setting.
2
 
[AUT
 O POWER SAVE]
Select [ON] to set [AMBIENT LIGHT DETECTION], [SIGNAL 
DETECTION], and [AV MUTE DETECTION].
3
 
[AMBIENT LIGHT DETECTION]
Enable ([ON])/disable ([OFF]) the ambient light detection 
function. 4

 [SIGNAL  DETECTION]
Enable ([ON])/disable ([OFF]) the signal detection function.
5
 
[A
 V MUTE DETECTION]
Enable ([ON])/disable ([OFF]) the AV mute detection function.
6
 
[NO SIGNAL
  SHUT-OFF]
Select the time until the projector enters the standby mode 
when the signal detection function is used.
7
 
[Submit]
Update the settings.
Note
 fFor detailed description of each setting item, refer to the [PROJECT OR SETUP] menu of the projector → [ECO MANAGEMENT] 
(x   page   79).  
						

							Chapter 4 Settings — [NETWORK] menu
114 - ENGLISH
[Change password] page
Click [Change password].
1
2
3
1 [Administrator]
Used to change the setting of the [Administrator].
2
 
[User]
Used to change the setting of the [User]. 3

 [Next]
Used to change the setting of the password.
[Administrator] account
1
2
3
4
5
6
7
1 [Account]
Displays the account to change.
2
 
[Current][User name]
Enter the user name before the change.
3

 
[Current][Password]
Enter the current password.
4

 
[New][User name]
Enter the desired new user name. (Up to 16 characters in single 
byte) 5

 [New][Password]
Enter the desired new password. (Up to 16 characters in single 
byte)
6
 
[New][Password(Retype)]
Enter the desired new password again.
7

 
[OK]
Determines the change of password.  
						

							Chapter 4 Settings — [NETWORK] menu
ENGLISH - 115
[User] account
1
2
3
5 4
1 [Account]
Displays the account to change.
2
 
[New][User name]
Enter the desired new user name. (Up to 16 characters in single 
byte) 3

 [New][Password]
Enter the desired new password. (Up to 16 characters in single 
byte)
4
 
[New][Password(Retype)]
Enter the desired new password again.
5

 
[OK]
Determines the change of password.
[Change password] (For user rights)
Only the change of password is enabled under the user rights.
1
2
4 3
1 [Old Password]
Enter the current password.
2
 
[New Password]
Enter the desired new password. (Up to 16 characters in single 
byte) 3

 [Retype]
Enter the desired new password again.
4
 
[OK]
Determines the change of password.
Note
 fTo change the account of the administrator, you must enter the [User name] and [Password] in [Current].  
						

							Chapter 4 Settings — [NETWORK] menu
116 - ENGLISH
[CRESTRON RoomView] page
The projector can be monitored/controlled with RoomView.
To start the RoomView control page from the web control screen, you need to access with the administrator rights. (For user rights, the 
[CRESTRON RoomView] button is not displayed on the web control screen.)
The control page of RoomView is displayed by clicking [CRESTRON RoomView].
It is not displayed if Adobe Flash Player is not installed on the computer used, or the browser\
 used does not support Flash. In that case, click 
[Back] on the control page to go back to the previous page.
Control page
1
2
3
4
5
6
7
1 [Tools]/[Info]/[Help]Tabs for selecting the setting, information, or help page of the 
projector.
2
 
[POWER]
Switches on/of

f the power.
3
 
[VOL
  DOWN]/[AV MUTE]/[VOL UP]
Operate the volume/AV mute.
These operations are not available when the power of the 
projector is turned off. 4
 [Input Select]
Controls input selection.
Not available when the power of the projector is turned of
f.
5
 
Menu screen control buttons
Navigates the menu screen.
6

 
Freeze/image quality adjustment
Controls items related to freeze/image quality

.
7
 
[Back]
Performs return to the previous page.
[Tools] page
Click [Tools] on the control page.
1
2
3
4
5
1 [Control System]
Set the information required for communicating with the 
controller to be connected with the projector.
2
 
[User Password]
Set the user rights password for the RoomV

iew control page.
3
 
[Admin Password]
Set the administrator rights password for the RoomV

iew control 
page. 4
 Network status
Displays the settings of wired LAN.
[DHCP]
Displays the current setting.
[IpAddress]
Displays the current setting.
[SubnetMask]
Displays the current setting.
[DefaultGateway]
Displays the current setting.
[DNSServer]
Displays the current setting.
5
 
[Exit]
Returns to the control page.  
						

							Chapter 4 Settings — [NETWORK] menu
ENGLISH - 117
[Info] page
Click [Info] on the control page.
45
6
7
1
2
3
8
1 [Projector Name]
Displays the projector name.
2
 
[Mac Address]
Displays the MAC address.
3

 
[Lamp Hours]
Displays the runtime of the projector (converted value).
4

 
[Power Status]
Displays the status of the power

. 5
 [Source]
Displays the selected image input.
6
 
[Lamp Mode]
Displays the light source mode.
7

 
[Error Status]
Displays the error status.
8

 
[Exit]
Returns to the control page.
[Help] page
Click [Help] on the control page.
The [Help Desk] window is displayed.
1
1 [Help Desk]
Send/receive messages to/from an administrator who uses 
Crestron RoomView.  
						

							Chapter 4 Settings — [DIGITAL LINK] menu
118 - ENGLISH
[DIGITAL LINK] menu
On the menu screen, select [DIGITAL LINK] from the main menu.
Refer to “Navigating through the menu” (x
  page   46) for the operation of the menu screen.
Switch the input to DIGITAL LINK.
Note
 fWhen the optional Digital Interface Box (Model No.: ET- YFB100G) is connected to the  terminal, the main menu of 
ET- YFB100G is displayed. Refer to the Operating Instructions of ET- YFB100G for details.
 fWhen a twisted-pair-cable transmitter of other manufacturer is connected\
 to the projector

, the main menu of the projector is displayed.  
						

							Chapter 4 Settings — [FOCUS] menu
ENGLISH - 119
[FOCUS] menu
On the menu screen, select [FOCUS] from the main menu.
Refer to “Navigating through the menu” (x
  page   46) for the operation of the menu screen.
The focus adjustment screen is displayed. Press asqw to adjust the focus.
Note
 fThe focus adjustment screen can be displayed by pressing the  but\
ton on the remote control.  
						

							Chapter 4 Settings — [SIGNAL LIST] menu
120 - ENGLISH
[SIGNAL LIST] menu
On the menu screen, select [SIGNAL LIST] from the main menu.
Refer to “Navigating through the menu” (x
  page   46) for the operation of the menu screen.
 rRegistered signal details
A1 (1-2)
When the signal of the address number (A1, A2, ...L7, L8) is registered. Sub memory number
Memory number:
 f
A name can be set for each sub memory (x   page   76).
Registering new signals
After a new signal is input and the  button on the remote control \
or the control panel is pressed, the registration is completed and the 
[MAIN MENU] screen is displayed.
Note
 fUp to 96 signals, including sub memories, can be registered to the proje\
ctor . fThere are 12 pages (eight memories of 
A through L, with eight memories possible on each page) for memory numbers, and the signal is 
registered to the lowest number that is available. If there is no availa\
ble memory number it will be overwritten from the oldest signal.
 f The names to be registered are automatically determined by the input sig\
nals and memory numbers. fIf a menu is being displayed, the new signals will be registered at the \
instant they are input.
Renaming the registered signal
Registered signals can be renamed.
1) Press  asqw to select the signal of which name is to be changed.
2)  
Press the  button.
 f The  [REGISTERED SIGNAL STATUS] screen is displayed.
 fThe input signal name, memory number

, input terminal, frequency, synchronization signal, etc., are displayed.
 fPress the  button or the  button to return to the 

[REGISTERED SIGNAL LIST] screen.
3) Press the  button.
 fThe  [RENAME] screen is displayed.
4) Press  asqw to select the text, and press the  button to enter the text.
5)  
After the name is changed, press 
 asqw to select [OK], and press the  button.
 fThe registration is completed and the  [REGISTERED SIGNAL  STATUS] screen returns.
 fWhen pressing  asqw to select [CANCEL] and pressing the  button, the changed signal \
name will not be registered and 
an automatically registered signal name will be used.
Deleting the registered signal
Registered signals can be deleted.
1) Press  asqw to select the signal to delete.
2)  
Press the  button.
 fThe  [ENTRY SIGNAL DELETE] screen is displayed.
 fT

o cancel deletion, press the  button or the  button to ret\
urn to the  [REGISTERED SIGNAL LIST] screen.
3) Press the  button.
 fThe selected signal will be deleted.