Philips Cbright Xg2 Projector User Manual

							Lamp
When operation time
reaches the last 100 hours
of the average lamplife, the
message ‘Warning: lamplife
has almost expired’ will be
displayed on the screen,
each time the projector is
switched on. The lamp
indicator lights up orange.
The lamplife remaining can
be checked using the OSD
menu.
1.Press the Menu.
–The menu bar appears
on the screen.
2.Use Cursor Control to
move the cursor to
Settings.
3.Use Cursor Control to
select Lamp counter.
–The remaining lamplife
hours are displayed in
the action window at the
bottom of the screen.
–When the lamplife has
expired,the lamp
indicator lights up red
and the message
‘Warning: lamplife has
expired’ is displayed on
the screen.
Lamp Replacement
Caution!
–For cooling purposes the lamp is open. When removing the
lamp do not tilt. If the inner tube is broken glass particles may
fall out.
–Be very careful. The lamp and lampholder may still be too hot
to touch.
–Keep lamp holder opening to your right. Do not touch lamp or
point lamp holder opening at anyone.
–A high-pressure lamp may break if handled improperly.
1.
Press the Stand by button to switch off the projector.
–The standby indicator lights up red.
2.Wait 5 minutes for the lamp to cool down and the cooling fan
to stop and disconnect the mains lead and all other cables.
3.Turn the projector over. Never place the projector on the side
where the connections are located!
4.
Unscrew the screws at the bottom of the cover and remove
the cover.
5.Read the caution and warning labels on the lamp cover.6.Unscrew the lamp holder.
FILTER
FILTER
L
A
M
PL
A
M
P
FILTER
FILTER
Multimedia projectors



Warning:

Lamplife has expired



It is suggested to change the lamp, 

to avoid sudden failure and to improve 

overall picture quality.
Display



Language

Keystone correction

Start-up screen

Lamp counter

System information

Factory reset

(more)



Lamp

5 hours



Lamp counter shows the operating hours of the 

lamp. It is suggested to reset when a new lamp is 

inserted. To reset keep OK key pressed 

for 3 seconds.Picture AudioSettings


Projector

2453 hours



Multimedia projectors



Warning:

Lamplife has almost expired



It is suggested to have a spare lamp available.

The lamp type is indicated in the user guide.
9. Maintenance
21 
						

							7.Grasp the lamp holder handle and carefully pull the lamp
holder out of the projector.
8.Carefully remove the new lamp housing from its package. Do
not touch lamp or point lamp housing opening at anyone. Do
not drop, as the impact may cause the lamp to break.
9.Place the lamp holder in the guiding slots and insert into the
lamp compartment.
10.Tighten the screws.11.Replace the cover and tighten the screws.12.Plug the projector back in by inserting the mains lead in the
Mains socket.
13.Press the Stand by On button to switch on the projector.14.Reset the lamp life time (see ‘Resetting the lamplife time’).15.Properly dispose of the old lamp.
Notes:–When replacing the lamp, always use the same type of lamp
LCA3111/00, 12NC 8670 931 11009).
–Please dispose of lamp in special chemical disposal bins.
Resetting the lamplife time
1.Press Menu.
–The menu bar appears on the screen.
2.Use cursor control to
select Settings in the
menu bar.
3.Use cursor control to
select Lamp counter in
the sub menu.
4.Press OK for 3 seconds to reset the lamp counter.5.If required, select another item you wish to adjust or press
Menu to exit.
Display



Language

Keystone correction

Start-up screen

Lamp counter

System informatyion...

Factory reset

(more)



Lamp

0 hours



Lamp counter shows the operating hours of the 

lamp. It is suggested to reset when a new lamp is 

inserted. To reset keep OK key pressed 

for 3 seconds.Picture AudioSettings


Projector

2453 hours



Settings
Display



Language

Keystone correction

Start-up screen

Lamp counter

System information...

Factory reset

(more)Picture Audio


FILTER
FILTER
FILTER
FILTER
9. Maintenance
22 
						

							If a fault occurs, first check the points listed below 
before taking the projector for repair. If you are unable to remedy
a problem by following these hints, consult your dealer or
service organisation.
Warning:
Under no circumstances should you try to repair the projector
yourself as this could invalidate the guarantee.
PROBLEM
–POSSIBLE CAUSE•SOLUTION
Image is not displayed
–Mains lead is not correctly connected.•Correctly connect mains lead.
–The filter holder is not installed correctly or is damaged.•Install the filter holder correctly (see ‘Cleaning the dust filter’
under ‘Maintenance’).
–Lamp holder cover is not closed correctly or the lamp holder
is damaged.
•Close the cover correctly (see ‘Lamp replacement’ under
‘Maintenance’).
–Signal cable not correctly connected.•Connect signal cable correctly.
–The projector is in Off position.•Press Stand by to switch on the projector.
Poor colour
•Select the correct data input (Computer or Component video)
in the Settings menu.
•Adjust brightness, contrast, saturation or hue (see ‘Display
and picture control’ under ‘Operation’).
Image is blurred
–Image is not focused.•Adjust focus ring.
–Distance between projector and screen is not correct.•Adjust the distance between the projector and the screen.
–Signal cable is not correctly connected.•Connect signal cable correctly.
Image does not match up with the projected screen
–Shift and/or Horizontal size are not adjusted correctly.•Adjust Shift or Horizontal size (See ‘Display and Picture
control’, sections ‘Data only’ and ‘Data and Video/S-Video’).
•Activate the auto-image function via the On Screen menu.
Picture rolls
–Signal cable is not correctly connected.•Connect signal cable correctly.
No sound
–Audio cable is not correctly connected.•Connect audio cable correctly.
–Volume is not adjusted properly.•Adjust volume.
–A/V-mute is active.•Cancel A/V-mute.
Caution!
Always reduce/check the volume setting of connected amplifiers
before switching off A/V mute, to prevent damage to speakers.
The projector does not react to commands from the remotecontrol
–Distance is too great.•Reduce distance.
–Batteries are exhausted.•Replace batteries (see ‘Inserting the batteries in the remote
control’).
–IR sensor is obstructed.•Remove obstacle.
Note: You can check if the projector receives the signal from the
remote control: the ring around the Standby button will
indicate this by fast flashing.
INDICATORS
Lamp indicator
–green:normal lamp condition.–orange: lamp life has almost expired (less than 100 hours to
go).
• See warning messages on the start up screen for details.
–red: lamp life has expired.
• Replace lamp. See ‘Maintenance’.
–red (fast blinking):lamp start has failed.
• Disconnect projector from the mains. Reconnect and
restart. If this does not resolve the problem, replace the
lamp. See ‘Maintenance’.
–slow blinking (green, red or orange):lamp is starting up or
cooling down.
Temperature indicator
–red:temperature error.
• The projector will go into Standby mode. Allow the
projector to cool down; this may take up to 30 minutes.
When the LED goes out press any button to activate the
projector again.
–fast blinking red:fan error.
• The projector will go into Standby mode. Make sure the
filter cover is closed properly; clean air inlets or dust filter
and allow the projector to cool down; this may take up to
30 minutes. When the LED stops flashing press any button
to activate the projector again.
Standby indicator (ring around Standby button).
–red:standby mode or projector cooling down.–green:operation mode or projector warming up
–fast blinking (red or green):remote control signal received.
–slow blinking (green): waiting on retry to start the lamp.
• Do not switch the projector off; it will restart the lamp
automatically within a few seconds.
10. Troubleshooting
23