Plus He 3200 Projector User Manual

User’s Manual
HE-3200English 

E – 2
Installation
* Allow at least 10 cm (3.9 inch) of space between the projector top
panel and its surroundings.
Also allow at least 10 cm (3.9 inch) of other spaces around the pro-
jector.
* The projector should be placed on a flat, level surface and in a dry
area free from dust and moisture.
* The projector should always be handled with care. Dropping or jar-
ring the projector could damage internal components.
* If you wish to have the projector installed on the ceiling do not attempt
to install...

E – 3
1) Read these instructions.All the safety and operating instructions should be read before the product is operated.
2) Keep these instructions.The safety and operating instructions should be retained for future reference.
3) Heed all warnings.All warnings on the product and in the operating instructions should be adhered to.
4) Follow all instructions.All instructions should be followed.
5) Do not use this apparatus near water.Do not use this product near water, near a bathtub, in a wet basement or...

E – 4
Major Features
High Image Quality
Use of a Digital Micromirror Device (DMDTM) chip that is based on
Texas Instruments Digital Light Processing (DLP
TM) technology
enables images of high contrast and high detail.

DLP technology gives rise to devices that exhibit high response
speed, which in turn enables excellent moving picture character-
istics and smooth images.

Use of a high-performance progressive scan converter provides
reproduction of film-like images.

Built-in color filters of high purity...

E – 5
Table of Contents
Important Safety Information ................................ E-2
IMPORTANT SAFETY INSTRUCTIONS ...................... E-3
Major Features ................................................. E-4
Accessories Check ............................................ E-6
Names of the Main Unit Parts ............................... E-7
Using the Storage Case ......................................................... E-9
Attaching the Supplied Adjusters .............................................

E – 6
Accessories Check
Remove the main unit and the accessories from the box and check that the following items are included.
Should an accessory be missing, please contact your store of purchase.
SET
ESC
MENU
ASPECT
VIDEO
     /YPbPrON/STANDBY
S-VIDEORGBDVISV
CV
RGB
DV
I
Remote control1
Controls the projector.
AA Batteries2
These batteries are for the remote control. Insert the batteries
at time of purchase.
See → Page E-11.
Power cable (1.8 m / 5.9 feet)
This power cord supplies power to the unit....

E – 7
Names of the Main Unit Parts
POWER
ON OFF
POWER/STATUSON/STANDBYASPECTSOURCE
Ventilation outflow holesThese ventilation outflow holes used for cooling
the main unit and discharge the heat of the lamp.
Attention!
Pay special attention to the ventilation outflow
holes. The heat from the lamp is discharged
from the ventilation outflow holes.
Remote control sensorThe remote control signal is received
here. → Page E-11
Air intake holeThis is an air intake hole used for
cooling the main unit.
Air intake...

E – 8
Names of the Main Unit Parts
ON/STANDBYASPECTSOURCE
POWER/STATUS
DVI-DRGBS-VIDEO VIDEO
Y Pb/Cb
 Pr/Cr
Theft prevention locking hole(See below)
Air intake holeThis is an air intake hole used for cooling the main unit.
Ventilation outflow holeThis ventilation outflow hole is used for cooling the
main unit and discharges the heat of the lamp.
DVI-D RGBS-VIDEO VIDEO
Y Pb/Cb Pr/Cr
S-VIDEO connectorThis is connected with the S-VIDEO output connector of the
equipment to be connected. → Page E-17
DVI-D...

E – 9
Names of the Main Unit Parts
Attaching the Supplied Adjusters
The supplied adjusters are required for vertical adjustment of the projector.
See → Page E-22 about Using the Adjusters
1. Remove a rubber pad of each front foot.
Note: The rubber pads are bonded. Being carful not to mar the plasticpart of the front feet, remove the rubber pads.
2. After putting projections on the back of the supplied adjuster into
depressions of the front feet, tighten the screws.
Front adjusterThese feet are used for...

E – 10
Names of the Remote Control Parts
S
E
T
ESC
MENU
ASPECT
VIDEO
     /YPbPrON/STANDBY
S-VIDEORGBDVISVCV
RGB
DV
I
Remote control transmitterThe infrared signal is sent from this part.
SET
ESC
MENU
ASPECT
VIDEO
     /YPbPrON/STANDBY
S
-VIDEORGBDVI
SV CV RGB DV I
ASPECT buttonThis button selects the vertical and horizontal ratio
of the screen of the input video. → Page E-23
These buttons are used for the
selection of the input.
For further information about input selection, see→ Page E-23
S-VIDEO...