Plus He 3200 Projector User Manual

E – 11
Preparing the Remote Control
Inserting the Batteries
When using the remote control for the first time, install the batteries that were supplied.
When replacing batteries, purchase two of the same type of AA battery.
Press and at the same time lift
the battery case cover at the
rear of the remote control to
remove it.
1
Follow the markings on the inside
of the case and insert the batter-
ies in the correct plus (+) and mi-
nus (-) directions.
2
First insert the tabs of the battery
case cover, then...

E – 12
The Procedure Up to Projecting to the Screen
P
O
W
E
R
O
NO
F
F
POWER/STATUSON/STANDBYASPECTSOURCE
1
2
3
4
7
5
9
8
6
Position the projector → Page E-13 Projection Distance and Screen Size
Determine the locations to place the screen and the projector.
Connecting the power cable → Page E-16 Power Cord Connections
Connect the video equipment and personal computer
Connect your equipment to the projector.
→ Page E-17 Connections with VIDEO and S-VIDEO Connectors
→ Page E-18 Connections with YCbCr...

E – 13
Placement Guide
Use this information as a guide to find the rough screen size when the projector is placed at a certain location, or to find out the
approximate size of a screen that will be required.
The projection distance over which focussing is adjustable is 1.2 m (3.9 feet) to 7.6 m (24.9 feet) from the lens surface of the main
unit. The projector should be placed within this range.
 1  Projection Distance and Screen Size
Screens with 4:3 Aspect Ratio (at an output size of 800 x 600)
This...

E – 14
Screens with 16:9 Aspect Ratio (at an output size of 800 x 450)
These are the projection distances for screens of 16:9 aspect ratio used for the viewing
of movie software and other applications.
The screen is placed within the projection distance range that corresponds to the screen
size designation. Within this range, the screen size can be adjusted with the zoom ring.Note:This is the projection distance when an aspect
ratio of [16:9 (LB)] has been selected. Selection of
Full, Auto or other...

E – 15
Screens with 16:9 Aspect Ratio (at an output size of 848 x 480)
These are the projection distances for screens of 16:9 aspect ratio used for the viewing
of DVD and other squeezed screen applications.
This projector uses an output size of 848 x 480 pixels for home theater applications and
enables the projection of a high definition 16:9 aspect ratio.
The screen is placed within the projection distance range that corresponds to the screen
size designation. Within this range, the screen size can be...

E – 16
Power Cable Connections
 2  Power Cable Connections
Use the supplied power cord to connect the power connector of the main unit with the power outlet.
POWER
ON OFF
POWER/STATUSON/STANDBYASPECTSOURCE
4
12
3
POWER switch
POWER/  indicator
Firmly insert all the way.
Power cable (supplied)
Firmly insert all the way.To wall outlet
Attention!
For pluggable equipment, install the projector as near to the power outlet socket that is easily accessible.
Do not switch off the main power or disconnect the...

E – 17
Connecting Video Equipment and Personal Computers
By connecting this unit with video equipment and using a DVD player or other source in combination with an audio/video amplifier
and speaker system will allow you to enjoy convincing home theater. Connecting the unit to a personal computer will permit
presentation data to be projected as a large screen display in conferences and lectures.
 3  Connections with VIDEO and S-VIDEO Connectors
These are connections made with equipment that is equipped...

E – 18
DVI-D RGBCTRL
S-VIDEO VIDEO
Y Pb/Cb
 Pr/CrGBS-VIDEO VIDEO
Y Pb/Cb Pr/Cr
COMPONENT COMPONENT
YCbCr YPbPr
G
BR
G
BR G
BRG
BR
 3  Connections with YCbCr/YPbPr Connectors
These are connections made with equipment such as DVD players that have YCbCr output connectors or YPbPr output connectors.
Make connections with the YPbPr/YCbCr connectors of this projector.
Component signal cable(available as an option)
(order code: 27-062)Make connections to the YCbCr
output jacks marked COMPONENT or...

E – 19
DVI-DRGBCTRL
S-VIDEO VIDEO
Y Pb/Cb
 Pr/Cr
DVI-D RGBVIDEO
Y 
DVI-D
MONITOR OUTPUT MONITOR OUTPUT
 3  Connection with RGB and DVI-D Connector
These connections are made with personal computers that have a monitor output RGB connector (analog signal) or a DVI-D
connector (digital signal). Connect personal computers having a mini D-Sub 15-pin RGB connector to the RGB connector of the
projector and connect personal computers having a DVI standard DVI-D connector to the DVI-D connector of the...

E – 20
Obtaining an External Output Signal from a Notebook Computer.
When projection will be with a notebook computer connected, knowledge will be required for the cable connection and notebook
computer startup procedure as well as the operation that follows notebook startup. Please consult the instruction manual of your
notebook computer or the on-line help while performing the following procedure.
1 Check whether a signal is being sent from the notebook computer to the projector.
An indication...