Proxima Pro Av 9400 Projector User Manual

51
OTHER FUNCTION SETTING
SETTING
DISPLAY MAIN MENU DISPLAY 1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear.
2. Press the POINT LEFT/RIGHT BUTTON(s) to select SETTING and press the SELECT (REAR CLICK) BUTTON.
Another dialog box SETTING DISPLAY will appear.
3. Press the POINT DOWN BUTTON and a red arrow will appear.
4. Move the arrow to an item you want to set by pressing the POINT UP/DOWN BUTTON(s).
5. If you want to change the setting, press the SELECT (REAR CLICK) BUTTON.
6....

52
OTHER FUNCTION SETTING
MAIN MENU DISPLAY
SETTING
DISPLAY NOTE: Do not reset the LAMP REPLACEMENT MONITOR TIMER, except after the lamp is replaced.
1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear.
2. Press the POINT LEFT/RIGHT BUTTON(s) to select SETTING and press the SELECT (REAR CLICK) BUTTON.
Another dialog box SETTING DISPLAY will appear.
3. Press the POINT DOWN BUTTON and a red arrow will appear.
4. Move the arrow by pressing the POINT UP/DOWN BUTTON(s) to select Lamp age...

53
The removable air filter prevents dust from accumulating on the surface of the projection lens and projection mirror. Should
the air filter become clogged with dust particles, it will reduce the cooling fans effectiveness and may result in internal heat
build up and reduce the life of the projector.
To clean the air filter, follow the cleaning procedures below:
1. Turn the LAMP POWER ON/OFF button OFF.
2. Remove the air filter cover.
3. Remove the air filter and sponge from the filter cover.
4. Clean...

54
APPENDIX
NOTE ON THE LAMP REPLACEMENT INDICATOR AND MESSAGE 
The LAMP REPLACEMENT INDICATOR and  the warning message LAMP REPLACEMENT indicates the
guide of the lamp life. 
It is unnecessary to replace the lamp immediately if the projector is operating normally with the indicator on.
If the LAMP REPLACE INDICATOR is lit (and warning message LAMP REPLACEMENT is displayed on the
screen) and the power is not be turned on by pressing the power button (Power is turned off approximately 20
seconds after...

55
Before calling your dealer or service station for assistance, follow these steps, to make sure everything is properly connected.
1. Make sure you have connected the projector to your equipment as described in section CONNECTING THE
PROJECTOR on pages 14 ~ 21.
2. Check cable connections. Verify that all computer, video and power cords are properly connected.
3. Verify that power is switched on.
4. If the projector still does not display an image, restart the computer.
5. If the image still does not...

No sound.
56
Problem:
Check Reverse L/R feature.
(See OTHER FUNCTION SETTING section on pages 50 ~ 51).Picture is L/R Reversed.
Check Reverse T/B feature.
(See OTHER FUNCTION SETTING section on pages 50 ~ 51).Picture is T/B inverted.
Check Display feature.
(See OTHER FUNCTION SETTING section on pages 50 ~ 51).Some displays are not seen
during the operation.
lCheck audio cable connection from audio input source.
lAdjust audio source.
lPress the VOLUME (+) button.
lPress the MUTE button.
lCheck the...

57
TECHNICAL SPECIFICATIONS
Projector Type
Dimensions (W x H x D)
Net Weight
LCD Panel System
Number of Pixels
Colour System
Scanning Frequency
Projection Image Size (Diagonal) 
Contrast Ratio
Horizontal Resolution
Projection Lens
Motorized Lens Shift
Throw Distance
Projection Lamp
Projection Mirror
AV Input Jacks
Computer Audio Input Jack Video Monitor Output Jack
Audio Monitor Output Jacks
Computer Input 1 Jack
Computer Input 2 Jack
Other Jack
Built-in Speaker
Image Elevation Adjustment
Voltage
Power...

Proxima Corporation warrants that the Proxima® Multimedia Projector Model Pro
AV 9400 product manufactured by Proxima is free from defects in materials and
workmanship under normal use during the Warranty Period.  The Warranty Period
commences on the day of purchase by the end-user.  The Warranty Period is two
years.  The projector lamp is not covered by this Warranty.
Each Proxima product is manufactured from new parts, or new and some used
parts.  In some cases, the product may have been delivered to...