Ricoh Aficio MP 6000SP User Manual

Interface Settings
51
2
❖Ethernet Speed
Set the access speed for networks.
Select a speed that matches your network environment. [Auto Select] should
usually be selected.
The default setting is Auto Select.
❖LAN Type
When you have installed the optional IEEE 802.11b interface unit, select inter-
face, IEEE 802.11b (wireless LAN) or Ethernet.
The default setting is Ethernet.
Appears when the IEEE 802.11b interface unit is installed.
If Ethernet and IEEE 802.11b (wireless LAN) are both connected to the...

System Settings
52
2
Parallel Interface
This section describes the user tools in the Parallel Interface menu under Inter-
face Settings.
Default settings are shown in bold type.
❖Parallel Timing
Sets the timing for the control signal of the parallel interface.
The default setting is ACK Outside.
❖Parallel Communication Speed
Sets the communication speed for the parallel interface.
The default setting is High Speed.
❖Selection Signal Status
Sets the level for the select signal of the parallel interface....

Interface Settings
53
2
IEEE 802.11b
This section describes the user tools in the IEEE 802.11b menu under Interface
Settings.
[IEEE 802.11b] is displayed when this machine is installed with the wireless LAN
interface board (optional).
Be sure to make all settings simultaneously.
Default settings are shown in bold type.
❖Communication Mode
Specifies the communication mode of the wireless LAN.
The default setting is Infrastructure Mode.
❖SSID Setting
Specifies SSID to distinguish the access point in...

System Settings
54
2
❖Wireless LAN Signal
Shows the radio wave conditions of the access point connected in infrastruc-
ture mode.
Radio wave status is displayed when you press [Wireless LAN Signal].
❖Transmission Speed
Specifies the communication speed of the IEEE 802.11b (wireless LAN).
The default setting is Auto Select.
❖Restore Factory Defaults
You can return the IEEE 802.11b (wireless LAN) settings to their defaults.
Print List
You can check items related to the network environment.
The...

Interface Settings
55
2
EPress [Exit].
FPress the {User Tools/Counter} key.
Note
❒You can also exit by pressing [Exit] on the User Tools main menu.
Downloaded From ManualsPrinter.com Manuals 

System Settings
56
2File Transfer
This section describes the user tools in the File Transfer menu under System Set-
tings.
Default settings are shown in bold type.
❖Delivery Option
Enables or disables sending stored or scanned documents to the ScanRouter
delivery server.
The default setting is Off.
Set this option when specifying whether or not to use the ScanRouter delivery
server. If you do, you will have to re-register I/O devices in the ScanRouter
delivery server.
❖Capture Server IPv4 Address
Specify...

File Transfer
57
2
 Delivery Failure File
If a received fax document cannot be sent to the ScanRouter delivery soft-
ware, it is stored in memory. To print a stored file, select [Print File], to de-
lete, select [Delete File].
If the machine can send the data to the ScanRouter delivery software, it
does so automatically. If you delete the data, you will not be able to distrib-
ute or print it.
Print File
 Delete File
❖SMTP Server
If DNS is in use, enter the host name.
If DNS is not in use, enter the...

System Settings
58
2
❖POP before SMTP
You can configure POP authentication (POP before SMTP).
When sending e-mail to an SMTP server, you can enhance the SMTP server
security level by connecting to the POP server for authentication.
To enable POP server authentication before sending e-mail via the SMTP
server, set [POP before SMTP] to [On]. E-mail is sent to the SMTP server after the
time specified for [Wait Time after Authent.] has elapsed.
The default setting is Off.
If you select [On], enter [Server...

File Transfer
59
2
❖Administrators E-mail Address
On e-mailed scanned documents, if the sender is not specified this appears as
the senders address.
When sending e-mail under the Internet fax function, administrators e-mail
address will appear as the sender’s address under the following conditions:
 The sender has not been specified and the machine’s e-mail address has
not been registered.
 The specified sender is not registered in the machine’s address book and
the machine’s e-mail address has not...

System Settings
60
2
❖Program / Change / Delete E-mail Message
You can program, change, or delete the e-mail message used when sending
an Internet fax or scan file as an attachment.
 Program / Change
APress [System Settings].
BPress [File Transfer].
CPress [TNext].
DPress [Program / Change / Delete E-mail Message].
ECheck that [Program / Change] is selected.
FPress [Not Programmed].
GPress [Change].
HEnter a name, and then press [OK].
Enter the name using up to 20 alphanumerical characters.
IPress...